Table of Contents
Advertisement
P
R O T O C O L A N D A D D R E S S S E L E C T I O N
7KHý5RER6FDQý3URýäìåýKDVýéý'0;ýRSHUDWLQJýPRGHVñýRUýSURWRFROVñýDQGýDý0DUWLQýPRGHïý7KHVHýDUHýGHVFULEHGýLQýPRUH
GHWDLOýRQýSDJH ìéï
(DFKýIL[WXUHýPXVWýEHýDVVLJQHGýLWVýRZQýFKDQQHOVýWRýUHFHLYHýLQVWUXFWLRQVýIURPýWKHýFRQWUROOHUïý7KHýDGGUHVVñýDOVRýNQRZQýDV
WKHýVWDUWýFKDQQHOñýLVýWKHýILUVWýFKDQQHOýXVHGïý$GGUHVVHVýDUHýLQGHSHQGHQWýRIýWKHýSK\VLFDOýRUGHUýRQýWKHýOLQNãýWKH\ýPD\ýEHýVHW
LQýDQ\ýFRQYHQLHQWýRUGHUïý7ZRý3URýäìåVýPD\ýVKDUHýWKHýVDPHýDGGUHVVâýKRZHYHUñýWKH\ýZLOOýUHFHLYHýWKHýVDPHýLQVWUXFWLRQV
DQGýLQGHSHQGHQWýFRQWUROýZLOOýQRWýEHýSRVVLEOHï
Mode
Control
Pan/tilt resolution
Channels required
1. Apply power to the RoboScan Pro 918. Press the [MENU] key and then press [↑] or [↓] until the display
shows
P SET
2. Press [↑] or [↓] until the desired protocol appears on the display. Press [ENTER] to confirm.
3. Press [↑] or [↓] until the display shows
address). Press [ENTER] to confirm.
4. Press [↑] or [↓] to select a DMX address from 1 to 512 or a Martin address from 1 to 31. Press
[ENTER] to confirm.
5. Press [MENU] to return to the main menu. Depending on the protocol selected, the DMX or Martin
address is displayed.
R
E A D O U T S
U s a g e r e a d o u t s (
Read the total number of power-on hours (
lamp hours since last reset (
reset (
RLS T
The resettable counters may be used to track overall usage and lamp life. To reset to zero, display the readout and then
press >↑@ for 5 seconds.
D M X v a l u e r e a d o u t s (
Read the DMX start code (
ture is receiving the expected commands. This feature is not applicable in Martin mode.
S o f t w a r e v e r s i o n r e a d o u t s (
Read the version number of the CPU software (
(
dIS P
). The CPU software version is also displayed for a moment at power up.
Te m p e r a t u r e r e a d o u t s (
Read temperature at the main printed circuit board (
below 25° C are shown as
The temperature sensors are calibrated at the factory and adjustment should not be necessary. The following procedure
calibrates the sensors if they give no or faulty readings.
1. Allow the unit to cool to room temperature (powered off for at least 4 hours).
2. Measure the room temperature in Celsius. (To convert F° to C°, subtract 32° and then multiply by 0.555.)
3. Power up the unit and allow it to reset.
4. Press the [MENU] and [↓] keys at the same time and hold them for 3 seconds until "25" shows in the display.
5. Press the [↑] and [↓] keys until the display shows the temperature measured.
6. Press [ENTER] to save the setting.
11
Martin
Vector
16 bit
2
. Press [ENTER].
)
T IME
R LAH
), total number of lamp strikes (
).
d MXL
ST CO
) and DMX values received for each effect. This is an easy way to check if the fix-
SPE C
- 25
; temperatures above 100° C are shown as
RoboScan Pro 918
DMX 1
DMX 2
Tracking
8 bit
16 bit
12
(to set a DMX address) or
dAd r
Po H
), power-on hours since last reset (
L STR
)
)
VE R
CPU
), 2051 microprocessor (
/
)
TEM P
PC b
) and in the effects section (
DMX 3
Tracking and/or Vector
8 bit
ìé
14
MAd r
RPo H
), total lamp hours (
), and the number of lamp strikes since last
20 51
), and display module software
F X
) in Celsius. Temperatures
+10 0
.
DMX 4
16 bit
ìç
(to set a Martin
LA H
),
Hide quick links:
Advertisement
Table of Contents
