Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Martin MAC 700 WASH
Summary of Contents for Martin MAC 700 WASH
- Page 1 MAC 700 Wash user manual...
- Page 2 270° 270° © 2006 Martin Professional A/S, Denmark. All rights reserved. No part of this manual may be reproduced, in any form or by any means, without permission in writing from Martin Professional A/S, Denmark. Printed in Denmark. P/N 35000185, Rev. C...
-
Page 3: Safety Information
If you have questions about how to operate the fixture safely, please contact your Martin dealer or call the Martin 24-hour service hotline at +45 70 200 201. - Page 4 Parliament and of the Council of the European Union on WEEE (Waste Electrical and Electronic Equipment), as amended by Directive 2003/108/EC, where applicable. Help preserve the environment! Ensure that this product is recycled at the end of its life. Your supplier can give details of local arrangements for the disposal of Martin products.
-
Page 5: Table Of Contents
Software installation..............22 MAC 700 Wash DMX protocol . -
Page 6: Introduction
Unpacking The MAC 700 Wash is packaged in either a cardboard box or a two-unit flight case that is designed to protect the product during shipment. The following items are included: • OSRAM HTI 700/D4/75 lamp (installed) •... -
Page 7: Ac Power
15 A fuse. Power connection Important! Connect the MAC 700 Wash directly to AC power. Do not connect it to a dimmer system; doing so may damage the fixture. You may need to fit the power cable with a power plug that is suitable for your AC power outlets. If so, install a grounding-type (earthed) plug following the plug manufacturer’s instructions. -
Page 8: Lamp
Lamp About the discharge lamp The MAC 700 Wash is designed for use with an OSRAM SharXS HTI 700 W/D4/75 lamp. This highly efficient double-ended short-arc source provides a color temperature of 7500 K, a color rendering index greater than 85, an average service life of 750 hours and hot restrike. - Page 9 Important! Align the lamp carefully. An excessive hot-spot will damage optical components. 1. Apply power and allow the MAC 700 Wash to reset. Using either a controller or the control menu, strike the lamp and project an open white beam on a flat surface.
-
Page 10: Dmx Data Link
Important! Never connect more than 1 data input and 1 data output. The MAC 700 Wash has both 3-pin and 5-pin XLR sockets for DMX input and output. The pin-out on all sockets is pin 1 to shield, pin 2 to cold (-), and pin 3 to hot (+). There is no connection to pins 4 and 5. -
Page 11: Rigging
Rigging The MAC 700 Wash can be placed on stage or clamped to a truss in any orientation. The mounting points allow the clamp brackets to be fastened parallel or perpendicular to the front as shown Figure 6. Figure 6: Clamp bracket positions and safety wire attachment point Warning! Always use 2 clamps to rig the fixture. -
Page 12: Control Panel
The DMX address and any status messages (see page 31) are displayed on the control panel when the MAC 700 Wash is powered on. To enter the menu, press [Menu]. Press [Up] and [Down] to move within the menu. To select a function or submenu, press [Enter]. To escape a function or menu, press [Menu]. -
Page 13: Readouts
D I M M E R → The dimmer curve setting ( ) provides two options for dimmer behavior. Select for a near-linear dimming curve or to simulate tungsten lamp dimming characteristics. D I S P L A Y The display intensity ( →... -
Page 14: Service Messages
10 seconds, feedback is automatically disabled. A D J U S T M E N T The adjustment menu ( → ) provides manual control for making mechanical adjustments. See page 29. MAC 700 Wash... - Page 15 C A L I B R A T I O N → The calibration menu ( ) provides utilities to define offsets in software that are relative to the mechanical reset or home positions. This allows you to fine tune optical alignment and achieve uniform performance between fixtures.
-
Page 16: Effects
Effects This section describes the effects in the MAC 700 Wash with reference to the DMX channels used to control them. See page 23 for the complete DMX protocol. The MAC 700 Wash has two DMX operating modes, 16-bit basic and 16-bit extended. The 16-bit basic mode uses 16 DMX channels, and 16-bit extended mode uses 23 channels. -
Page 17: Cyan, Magenta, Yellow And Color Temperature Control
channel 16 (in basic mode) or 23 (in extended mode) if you want to obtain instant snap dimming to/from intermediate values (e.g. if you want a snap from 100% to 50% or from 20% to 70%). Fine control of the dimmer is available on channel 3 in extended mode. Cyan, magenta, yellow and color temperature control Cyan, magenta, yellow and CTC can be added on channels 3, 4, 5 and 6 respectively (4, 6, 8 and 10 in extended mode). - Page 18 P E R S O N A L I T Y O V E R R I D E S The pan/tilt speed channel provides tracking values that allow you to override the pan/tilt speed setting from the controller. The effects speed channel provides values for overriding the shortcuts setting for the color wheel. MAC 700 Wash...
-
Page 19: Optical Configuration
The MAC 700 Wash features a color wheel with 8 interchangeable dichroic color filters and an open position. As standard the MAC 700 Wash is supplied with six color filters, a 3200 - 4100 K CTC filter and a UV transmitter filter that gives ultraviolet ‘black light’ installed. The illustration shows the filter positions as seen from the lamp side. -
Page 20: Routine Maintenance
Routine maintenance The MAC 700 Wash requires routine cleaning. The schedule depends heavily on the operating environment. It is essential to follow the cleaning guidelines given later in this section. Refer any service operation that is not described here to a qualified Martin technician. -
Page 21: Cleaning
Cleaning schedules for lighting fixtures vary greatly depending on the operating environment. It is therefore impossible to specify precise cleaning intervals for the MAC 700 Wash. Cooling fans suck in airborne dust and smoke particles, and in extreme cases fixtures may require cleaning after surprisingly few hours of operation. -
Page 22: Replacing The Lamp Socket
The following are required in order to install software. • The MAC 700 Wash update file, available for download from the User Support Area of the Martin web site (http://www.martin.com). • The Martin Software Uploader program, version 5.0 or later, available for download from the User Support Area of the Martin web site. -
Page 23: Mac 700 Wash Dmx Protocol
MAC 700 Wash DMX protocol 16-bit 16-bit Basic Extended Mode Mode DMX Value Percent Function Shutter, strobe, reset, lamp on/off 0 - 19 0 - 7 Shutter closed (lamp switches to 400 W mode after 10 seconds while shutter is closed) - Page 24 6 and 8 in extended mode) 136 - 175 54 - 69 Fast 176 - 215 70 - 84 Medium 216 - 255 85 - 100 Slow Zoom (MSB) Flood → spot 0 - 255 0 - 100 MAC 700 Wash...
- Page 25 249 - 251 Tracking, (menu override) 252 - 255 99 - 100 Blackout while moving Beam shaper 0 - 251 0 - 98 Normal (no blackout) 252 - 255 99 - 100 Blackout while moving MAC 700 Wash DMX protocol...
-
Page 26: Control Menu
Dimmer curve simulates tungsten incandescent bulb characteristics Disable CMY blackout Enable CMY blackout Return all settings (except calibrations) to factory defaults , , Load custom configuration Save current custom configuration Table 2: Control menu MAC 700 Wash... - Page 27 Menu Item Options Notes (Default settings in bold print) Total hours of operation since manufacture Hours of operation since counter reset (see page 13) Total hours of operation with lamp on since manufacture ...
- Page 28 Set all effects to calibration value 128 PCB test: for service use only Cooling fans: full speed Cooling fans: temperature regulated Manually set fixture to software update mode Table 2: Control menu MAC 700 Wash...
-
Page 29: Adjustment Submenu
Adjustment submenu menu is for use by service technicians when performing adjustments. Menu Item Item Options Notes Reset fixture Strike lamp Douse lamp Dimmer blades against stop Close dimmer Dimmer to open position ... -
Page 30: Control Menu Shortcuts
Control menu shortcuts The following shortcuts are available using the buttons in the MAC 700 Wash control panel: Shortcut Function Hold [Menu] and press [Up] Resets fixture Hold [Enter] and press [Up] Strikes lamp Hold [Enter] and press [Down] Douses lamp... -
Page 31: Display Messages
Check lamp. Check that local voltage is (Lamp error) reasons are a missing or defective lamp, or within specification. insufficient AC voltage. Contact Martin service personnel for (Memory error) ...the EEPROM memory cannot be read. assistance. last character in display rotates ...a software upload is unsuccessful. -
Page 32: Troubleshooting
Time out error after fixture reset. Effect requires mechanical adjustment. Martin technician for service. Mechanical effect loses Mechanical train requires cleaning, Contact Martin technician for service. position. adjustment, or lubrication. Send LAMP OFF command before sending another Lamp fails to strike after turning LAMP ON command. -
Page 33: Circuit Board Connections
Circuit board connections Circuit board connections... -
Page 34: Mac 700 Wash Specifications
MAC 700 Wash specifications P H Y S I C A L Length ..............450 mm (17.7 in) Width . - Page 35 MAC 700 Wash in cardboard packing case ........
- Page 36 Gradav Hire and Sales Ltd Unit C6 Hastingwood Trading Estate Harbet Road London N18 3HU Phone 020 8803 7400 FAX 020 8803 5060 email office@gradav.co.uk Web www.gradav.co.uk...
Need help?
Do you have a question about the MAC 700 WASH and is the answer not in the manual?
Questions and answers