(800) 523-9361 or (888) 2-FOLLETT, or (610) 252-7301. Operation Before you begin Check your paperwork to determine which model you have. See the explanation of 110 series model numbers below. C110R5A Condenser type – A = air-cooled, W = water-cooled Icemaker capacity –...
How dispenser works Follett's 110 series ice dispensers are available as either manual load models (using ice from another source) or automatic load models fed from one or two Follett 400 lbs (181kg)/day icemakers. Depending on the model, the icemaker may be located in the base of the dispenser, mounted on top or remoted to a location up to 20 feet (6m) from the dispenser.
Page 4
How chilled water accessory works Follett’s chilled water accessory uses ice from the dispenser’s storage hopper to chill the incoming water supplied to the water station. The water chiller assembly is located in the dispenser cabinet under the storage hopper. As ice is dispensed, or the wheelmotor is energized during the level fill cycle, ice is automatically fed into the water chiller assembly to chill the water coil inside the assembly.
Page 5
SensorSAFE ™ dispensers – Deactivate dispenser by depressing and releasing clean switch located on left side of unit under top front cover. Clean lens using soft cloth and mild, non-abrasive cleaner. Reactivate dispenser by depressing and releasing clean switch a second time. Recommended quarterly cleaning of dispenser hopper 1.
Replace switch. c. Wheel motor malfunction. c. Check motor and capacitor and replace as required. d. Non-compatible ice used in d. Load compatible ice. (Call Follett for dispenser. guidance.) e. Faulty dispense solenoid. e. Check solenoid and replace if faulty.
Page 7
Troubleshooting SensorSAFE ™ board and sensors Problem: Does not dispense ice and/or water ACTION LED STATUS SOLUTION ICE/WTR Check LEDs on control Check circuit breakers and power switch; board restore power or replace defective switch. Depress clean switch located under left side of front cover to return board to normal operation Place cup under drop Troubleshoot appropriate lens/sensor and...
Parts removal Dispense chute removal 1. Remove stainless front cover. 2. Turn power to unit off (ON/OFF switch is located at right side of electrical box). 3. Slide plastic dispense chute cover up and out to remove. 4. Remove four (4) fasteners holding dispense chute and bracket assembly in place and remove chute. Dispense wheel removal 1.
Wiring diagrams How unit works — lever actuated model The wheel motor and dispense solenoid are energized through the power and ice dispense switches. The water solenoid is energized through the power and water dispense switches. Automatic load units with either top-mounted or remote icemakers are equipped with a level fill circuit to maximize fill in the ice storage area by rotating the wheel at intervals until the bin is completely filled.
Page 10
How unit works — SensorSAFE models ™ When a container is placed within the actuation zone below the ice or water chute on the SensorSAFE dispenser models, an invisible, randomly-generated infra-red signal is emitted, reflected off the container and detected by the sensor.
Page 11
Thermostat locations – freestanding units and units with remote icemakers Top view bin thermostat Thermostat locations – units with top-mounted icemakers Top view hand bend cap Detail A–A tube end to approx. 45˚ as shown in Detail A–A. Approx. 3/4" 45˚...
Page 12
Replacement of ice transport tube – Units with top-mounted icemakers If preparing tubing not supplied by Follett, dispenser end of ice tube tube must be fitted with mounting pins as shown in drawing. ice tube mounting pin bracket plate 1. Slip a hose clamp on end of transport tube without pins, immerse this end...
Page 13
Parts cold drinks Part # Description Reference # 501445 Top, dispenser 501819 Lid, top Not shown 501502 Cover, front, stainless steel, with “cold drink” graphics 501596 Cover, front, stainless steel, with “ice” graphics 500089 Leg kit, 6" (153mm) for F1105A/W units only 501478 Leg kit, 4"...
Hopper components Dispense wheel - top view Side view cutaway Dispense wheel - bottom view Part # Description Reference # 501493 Wheel, dispense (includes 501320, 501494, 501441) 501346 Agitator, fixed 501603 Thumbnut, fixed agitator rod 501802 Baffle, ice 501340 Capacitor, run, dispense motor 501803 Motor, wheel (includes 501340) 501804...
Page 18
Top view - units with Top view – freestanding units and units top-mounted icemakers with remote icemakers Side view - units with top-mounted icemakers Side view - freestanding units and units with remote icemakers Back wall Part # Description Reference # 502056 Bracket, ice tube 501842...