Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for DKS 1601
Summary of Contents for DKS 1601
- Page 1 1601/1602 barrier gate operator - installation guide...
-
Page 2: Table Of Contents
.....................4 1601-080/081 glossary ........................5 1602-080/081 specifications ......................6 with circuit board 1601-010 rev. V or higher operator installation surface operator ......................7 supplemental manual available (P/N 2340-065) for 1601-081, 1601-088 electrical installation and 1602-081 for optional battery main terminal wiring ....................9... -
Page 3: Safety Information
ARDS; Pinch Points, Entrapment, Ab- with a separate access. sence of Controlled Pedestrian Access, All electrical connections should be made Traffic Backup. in accordance with local electrical codes. 1610 Speed Bumps Operator Danger Zone L I M Speed Limit Sign 4 installation guide 1601-065-M-05-07... -
Page 4: Glossary
ENTRAPMENT - The condition when an object is caught or held in a position that increases the risk of injury. 1601-065-M-05-07 installation guide 5... -
Page 5: Specifications
The 1601 operator has been designed for high usage single lane (14 feet maximum) vehicular traffi c control. class: II, III, IV horsepower: 1/2 or 1 HP housing: G90 galvanized steel, painted white. mechanical: worm gear running in a continuous oil bath. -
Page 6: Surface Operator
•Loop Lead Conduit Run conduits from the operator to their •Sequencing Control or corrsesponding source . Primary/Secondary Conduit Mix and pour concrete into the trench, al- low the concrete to cure and place the op- erator into position. 1601-065-M-05-07 installation guide 7... - Page 7 3/8 x 3 or 1/2 x 3, anchors are not included. Place the operator into position and bolt down using the sleeve anchors. The operator’s access door must face the opposite side of traffic. 8 installation guide 1601-065-M-05-07...
-
Page 8: Electrical Installation
11. ENABLE UP INPUT - This input is used when sequencing the 1601 with a slide or swing gate operator in PAMS applications. This input is only active after a MOMENTARY UP input is received. -
Page 9: High Voltage Wiring
WIRE SIZE / DISTANCE IN FEET MODEL VOLTS AMPS 12 AWG 10 AWG 8 AWG 6 AWG 1601/1603 1601/1603 1100 1830 2750 1601/1603 1.35 2875 4600 7665 11500 The distance shown in the chart is measured in feet from the operator to the power source. -
Page 10: Low Voltage Wirng
1000 feet. All inputs to the terminal strip must be NORMALLY OPEN. If this operator is part of a Perimeter Access Management System (PAMS), refer to your PAMS wiring manual and section 2.3.3 for interface wiring to the swing or slide gate operator. 1601-065-M-05-07 installation guide 11... -
Page 11: Primary/Secondary Control Wiring
1 2 3 4 5 6 7 8 9 10 11 12 13 14 1 2 3 4 5 6 7 8 9 10 11 12 13 14 3 4 5 6 7 8 9 10 11 12 13 14 12 installation guide 1601-065-M-05-07... -
Page 12: Pams Wiring
1 2 3 4 5 6 7 8 9 10 11 12 13 14 9 10 11 12 13 14 15 16 17 18 19 20 9 10 11 12 13 14 15 16 17 18 19 20 1601-065-M-05-07 installation guide 13... -
Page 13: Gate Tracker Wiring
Wire connection from the tracker board terminal P1-6 to the terminal 6 is optional if the barrier operator is not to be activated by the tracker output relay. For more detailed information on Gate Tracker™ and wiring to the Tracker expansion boards, refer to the Tracker Installation and Wiring Manual, DoorKing P/N 2351-010. 14 installation guide 1601-065-M-05-07... -
Page 14: Loop Detector Wiring
If using other loop detectors, refer to the separate. Loop layouts shown are for typical barrier gate applications. If using other loop detectors refer to the separate Loop Information Manual for installation instructions, loops/preformed loops and wiring diagrams. 1601-065-M-05-07 installation guide 15... -
Page 15: Entry Lane Application
TB-1 and the ARMING loop to terminals TB-2. If the optional arming loop is not used, use a 9406 detector plugged into the DOWN port on the 1601 circuit board and connect the DOWN loop to terminals TB-1 on this detector. -
Page 16: Exit Lane Application
Use a 9406 detector plugged into the DOWN port on the 1601 circuit board and connect the DOWN loop to terminals TB-1 on this detector. Use a second 9406 detector plugged into the UP port on the 1601 circuit board and connect the EXIT loop to terminals TB-1 on the detector. -
Page 17: Ticket Spitter Application
Use a 9405 loop detector plugged into the DOWN port on the 1601 circuit board. Connect the DOWN loop to terminals TB-1 and the TICKET EJECT loop to terminals TB-2. The timer (SW-1, switch 7) should be OFF. The arm will rotate down after the vehicle clears the down loop. -
Page 18: Two-Way Lane Application
TB-1 and the ARMING loop to terminals TB-2. If the optional arming loop is not used, use a 9406 detector plugged into the DOWN port on the 1601 circuit board and connect the DOWN loops, wired in series, to terminals TB-1 on this detector. -
Page 19: Timer Down Application
TB-1 and the ARMING loop to terminals TB-2. If the optional arming loop is not used, use a 9406 detector plugged into the DOWN port on the 1601 circuit board and connect the REVERSE loops, wired in series, to terminals TB-1 on this detector. -
Page 20: Hub
(2) Hex Bolt (1) Mounting Hub Install the arm hub with the mounting holes in a X pattern when the operator is in the down position. (3) Locking Plate (4)Screw 1601-065-M-05-07 installation guide 21... -
Page 21: Aluminum-Plastic-Wood
Attach the mounting bracket to the hub using the supplied hardware, DO NOT TIGHTEN BOLTS. Slide the barrier arm into the mounting bracket. Tighten the mounting bracket to the hub as shown. ALUMINUM PLASTIC WOOD 22 installation guide 1601-065-M-05-07... -
Page 22: Wishbone
Install the 10’ ft. barrier arm between the two 14’ ft. arms us- ing the supplied hardware. Install the inside/outside counterweight plates on the barrier arms using the supplied hardware. Check for correct shaft rotation. Refer to page 21 when installing the hubs. 1601-065-M-05-07 installation guide 23... -
Page 23: Control Board
8. GATE OPERATOR DATA TERMINAL - Operator status reporting; cycle count, shorted inputs, loop detector problems, power interrup- tions, etc. 24 installation guide 1601-065-M-05-07... -
Page 24: Magnetic Limit
MAGNETIC LIMIT ADJUSTMENT 1 2 3 4 5 6 7 8 9 10 11 12 13 14 POWER AUTO DOWN 6 7 8 9 10 11 12 13 14 1 12 1 POWER AUTO DOWN 1601-065-M-05-07 installation guide 25... -
Page 25: Direction Check
Reinstall the plastic circuit board cover and repeat step 1 to check rotation. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 13 14 POWER AUTO DOWN POWER AUTO DOWN 26 installation guide 1601-065-M-05-07... -
Page 26: Reverse Sensitivity
1 12 1 external reversing devices such as loops, photo electric eyes, or reversing edges. It POWER AUTO is important that these devices be in- DOWN stalled according to the needs and re- quirements of your particular application. 1601-065-M-05-07 installation guide 27... -
Page 27: Switch Descriptions & Functions
Remember multiple inputs. SW 1, switch 4 must also be on. Multiple Input Second Car Down – If a vehicle is on the down loop when the 1601 receives Memory Options another UP command, the operator will ignore the close command when the first vehicle clears the down loop and will require the second vehicle to clear the down loop to lower the arm. -
Page 28: Reversing Edge
Route the lead-in wire through the hole and connect to terminals 9 and 14 without interfering with any moving parts. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 1601-065-M-05-07 installation guide 29... -
Page 29: Fan Kit
ON - Turns the fan on continuously. AUTO - Normal setting. The fan will automatically turn on when the temperature inside the cabinet rises above 90°F, and will turn off when the temperature drops below 90°F. 30 installation guide 1601-065-M-05-07... -
Page 30: Heater Kit
AUTO - Normal setting. The heater will automatically turn on when the tem- perature inside the cabinet falls below 40°F, and will turn off when the tem- perature rises above 40°F. 1601-065-M-05-07 installation guide 31... -
Page 31: Wiring Diagram
32 installation guide 1601-065-M-05-07... -
Page 32: Wiring Diagram-Convenience Open
1601-065-M-05-07 installation guide 33... -
Page 33: Maintenance Schedule
2. Place the AC power switch to the OFF position. The arm should rotate to the UP position approximately two seconds after the AC power switch is shut off. 3. Turn the AC power switch to the ON position. The operator will re- sume normal operation. 34 installation guide 1601-065-M-05-07... -
Page 34: Technical Information
Check that the back-up system toggle switch is in the ON position. raise arm upon malfunction. Refer to the wire size chart · power outage. Check the batteries for proper voltage, replace if necessary. on page 10. · Replace the 2340-010 control board. 1601-065-M-05-07 installation guide 35... -
Page 35: Accessories
The following accessories are available for 1601 operators. Loop Detector /plug directly into ports on circuit board simplifying wiring. P/N 9406-010 - Single channel detector. P/N 9405-010 - Two channel detector. Loop Wire /with XLPE insulation is available in 500 and 1000 foot rolls, available in Black, Blue and Red insulation. - Page 36 DKS DoorKing, Inc 1601-065-M-05-07 Designed by DKS, DoorKing in California...