Related Manuals for Premier Mounts UFM-4
Summary of Contents for Premier Mounts UFM-4
-
Page 1: Installation Manual
INSTALLATION MANUAL UFM-4 Premier Mounts 3130 E. Miraloma Avenue Anaheim, CA 92806 Phone: (800) 368-9700 Fax: (800) 832-4888 mounts@mounts.com www.mounts.com Rev. 02... - Page 2 PBL-110 Projector Mount Page - 2 - Installation Manual...
-
Page 3: Table Of Contents
Mounting Bracket Installation ...........................- 9 - Wall Stud Location ............................- 12 - Installing the Flat Panel Display ........................- 17 - Technical Specifications ..........................- 19 - Warranty ................................- 20 - Contact Premier Mounts ..........................- 20 - Notes ................................- 21 - Installation Manual Page - 3 -... -
Page 4: Warning Statements
UFM-4 Warning Statements THE WALL STRUCTURE MUST BE CAPABLE OF SUPPORTING 210 LBS. IF NOT, THE WALL WARNING: STRUCTURE MUST BE REINFORCED. PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN, AS OUTLINED IN THE INSTALLATION INSTRUCTIONS, MUST BE ADHERED TO. FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY, OR EVEN DEATH. -
Page 5: Parts List
This wall mount is shipped with all proper installation hardware and components. Make sure that none of these parts are missing and/or damaged before beginning installation. If there are parts missing and/or damaged, please stop the installation and contact Premier Mounts (800-368-9700). - Page 6 UFM-4 M5 x 25 (Qty 8) M8 x 20 (Qty 8) M5 x 30 (Qty 8) M8 x 25 (Qty 8) M6 x 20 (Qty 8) M8 x 30 (Qty 8) M6 x 25 (Qty 8) M8 x 35 (Qty 8)
- Page 7 UFM-4 Nylon spacers and flat washers actual size NOTE: The nylon spacers may be staked to achieve proper spacing. M8 Nylon M5 Nylon (Qty 8) (Qty 8) Spacers Spacers 442 Nylon M6 Nylon (Qty 12) (Qty 8) Spacers Spacers 5/16” Flat...
-
Page 8: Thread Depth Indicator
UFM-4 Thread Depth Indicator Insert the thread depth indicator (supplied) through the thread inserts found on the back of the flat panel to make sure the inserts measure the same full depth and mark it (Figure 1). Locate the correct diameter screw for the thread insert. Compare your marking to the screws (supplied). -
Page 9: Mounting Bracket Installation
UFM-4 Mounting Bracket Installation NOTE: Proper installation procedure by qualified personnel as outlined in the installation instructions must be adhered to. Failure to do so could result in serious personal injury and possible damage to the flat panel. WARNING: INVERT THE FLAT PANEL AND PLACE IT ON A SOFT, FLAT SUFRACE TO PREVENT DAMAGE TO THE FLAT PANEL. - Page 10 UFM-4 If needed, install the nylon spacers to the mounting points on the flat panel (Figure 6). Lay the left and right mounting brackets (stamped arrows facing out) - (Figure 7). Nylon Spacers, If Applicable Mounting Brackets Center Mark Inverted Flat Panel...
- Page 11 UFM-4 Mounting Bracket Bottom of Flat Panel Center of Viewing Guide Center of Flat Bottom of the Align the Mounting Flat Panel Panel Brackets Figure 8 Figure 9 The Griplates™ have M4, M5, M6 and M8 hole patterns to fit the hardware that your flat panel requires.
-
Page 12: Wall Stud Location
UFM-4 Wall Stud Location Using a (commercially available) wood stud finder, locate four 16" or 24" stud centers behind the wall. Once found, make a pencil marking on the center of the wood studs (Figure 12). NOTE: The wall plates have (3) 16" and (1) 24" mounting slot positions (see Technical Specifications on Page 17) Measure from the floor to the desired viewing height and mark the wall. - Page 13 UFM-4 To connect the two wall plates, lay them on a flat surface, end to end. Make sure that the holes line up (Figure 14). Insert two (2) M8 x 16mm Hex Head bolts through the two holes and secure with two (2) M8 Hex nuts (Figure 14).
- Page 14 UFM-4 Place the bottom portion of the wall plate to the reference line and mark the eight (8) lag bolt mounting points through the wall plate slots on the wall. Level the wall plate with the reference arrow pointing up to the ceiling (Figure 14).
- Page 15 UFM-4 Level and secure the plate to the wall with the reference arrow facing up to the ceiling. Secure the plate using the eight (8) 5/16" lag bolts and flat washers (supplied) – (Figure 17). CAUTION: Do not over tighten the lag bolts.
- Page 16 UFM-4 Level and secure the plate to the wall with the reference arrow facing up to the ceiling. 10. Use a minimum diameter of 5/16” x 2 ¼” large concrete wedge anchors (commercially available) – (Figure 18). CAUTION: Do not over tighten the wedge anchors bolts.
-
Page 17: Installing The Flat Panel Display
UFM-4 Installing the Flat Panel Display WARNING: AT LEAST (2) QUALIFIED PERSONNEL ARE STRONGLY RECOMMENDED FOR INSTALLATION OF THIS PRODUCT. FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY AND POSSIBLE DAMAGE TO THE FLAT PANEL. Raise the flat panel with the LEFT and RIGHT mounting brackets secured to the flat panel and insert the top hooks from each bracket to the rod from the wall plates (Figure 19). - Page 18 UFM-4 Make any lateral shift adjustment and lock it by tightening the two (2) ¼”-20 Phillips screws found on the bottom of the mounting brackets. Use the wall bumper to adjust your flat panel. CAUTION: Do not over tighten the ¼”-20 screws to the rods (Figure 20).
-
Page 19: Technical Specifications
UFM-4 Technical Specifications Figure 21 Installation Manual Page 19... -
Page 20: Warranty
Warranty Limited Lifetime Warranty All Premier Mounts products carry a limited lifetime warranty from ship date against defects in materials and workmanship. Premier Mounts is not liable for improper installation that results in damage to mounts, adapters, display equipment or personal injury. -
Page 21: Notes
Shilton, Coventry, England CV79JY Gunma-ken 370-3524, Japan Phone: 800-368-9700 Phone: +44 (0) 2476 614700 Phone: 81.27.371.6998 Fax: 800-832-4888 Fax: +44 (0) 2476 614710 Fax: 81.27.371.6308 Other Locations – Phone: 001.714.632.7100; Fax: 001.714.632.1044 ©Premier Mounts 2005 Rev. 02 Installation Manual Page - 21 -...
Need help?
Do you have a question about the UFM-4 and is the answer not in the manual?
Questions and answers