Page 1
Device of this mark is a trademark of Sharp Corporation. Plasmacluster is a registered trademark or a trademark of Sharp Corporation. IG-ETC1A...
Page 6
FILTER UNIT CLEAN RESET (Press 3sec.) SWING 10 1(( TIMER AIR VOLUME POWER HIGH FINE ADJUSTMENT TIMER RHYTHM WIND ION MODE • • POWER ION MODE VOLUME FINE ADJUSTMENT SWING TIMER RHYTHM WIND...
Page 7
IG-ETC1A • • • • POWER ION MODE VOLUME FINE ADJUSTMENT SWING TIMER RHYTHM WIND •...
Page 10
• POWER POWER POWER HIGH • • • POWER VOLUME • HIGH • • FILTER UNIT CLEAN RESET (Press 3sec.) SWING POWER HIGH FINE ADJUSTMENT TIMER RHYTHM WIND ION MODE 60° • 90° 120° • •...
Device of this mark is a trademark of Sharp Corporation. Plasmacluster is a registered trademark or a trademark of Sharp Corporation. Plasmacluster Ion Generator IG-ETC1A OPERATION MANUAL IG-ETC1E *1 "High-Density 25000" is the approximate amount of ions that a Plasmacluser Ion Generator equipped with a PCI Ion Generating Unit generates per cubic centimeter;...
SPECIFICATIONS ............. E-19 TROUBLESHOOTING • While IG-ETC1A/IG-ETC1E can remove suspended viruses and other contaminants, it cannot create a completely sterile environment. SHARP does not guarantee its ability to prevent microbial infection. • To enable stable emission of high-density Plasmacluster ions, the Plasmacluster Ion Generating Unit mounted in IG-ETC1A/IG-ETC1E will need to be replaced periodically*.
• Do not connect other appliances to the same socket using an extension cord, and do not bundle the cord. (Doing so could cause ¿ re.) • Use only a 220V outlet for IG-ETC1A, 220-240V outlet for IG-ETC1E. • Use the AC adapter designed exclusively for this product, and insert the AC adapter securely all the way into the power socket until it stops.
IG-ETC1A/E CAUTIONS CONCERNING OPERATION: • Do not pull on the cord when unplugging the AC adapter. (Doing so could lead to fire or electric shock.) • Pull out the AC adapter from an outlet when the product is not in use. (To avoid possibility of electric shock, short circuit or ¿...
Unit holder Fan cover Filter Accessories • AC adapter • Remote control • Unit cleaning brush (Wirelessly) (Installed inside the body) < IG-ETC1A > Plug for connecting POWER ION MODE Plug the main unit VOLUME FINE ADJUSTMENT SWING TIMER...
PREPARATION Set batteries in the remote control (Replacement of batteries) Remove a cover on the rear side of the remote control. Cover Set batteries following indications properly. (AAA dry-cell battery DC1.5V x2) Attach the cover. Operation of the remote control Receiver window •...
Page 31
Connecting the AC adapter Insert the plug for connecting the main unit to the end of power input terminal of the main unit securely. Insert the plug of AC adapter main unit securely. < IG-ETC1A > < IG-ETC1E > Power supply input terminal...
OPERATION Power ON Press the Operation Button. Main unit Remote control Note: Beep Control panel • I m m e d i a t e l y a f t e r t h e A C POWER adapter is plugged in, the unit wil operate at air volume level 1 POWER POWER...
Page 33
IG-ETC1A/E Adjust the vertical swing angle (When the vertical swing operation OFF) Press the Vertical Swing Button. Main unit Remote control • Every time when you press the Vertical Swing Button, the louver operation switches to "ON" Beep or "OFF".
Page 34
OPERATION Adjust the air volume ¿ nely Press the Air Volume Fine Adjustment Main unit Remote control Button. Beep • The air volume can be ¿ nely adjusted to 32 levels with the Air Volume Fine Adjustment Button. FINE FINE •...
Page 35
IG-ETC1A/E Timer operation Timer ON and Timer OFF cannot be set together. [ Timer OFF (When power ON) ] (The operation is automatically stopped at the set time) Select your favorite timer time. Main unit Remote control TIMER • The Timer Indication Light and OFF Timer Light (white) Beep light up.
Page 36
OPERATION Ion mode operation During operation, select your favorite Main unit Remote control Ion mode. ION MODE Beep • There are 4 modes shown below. ION MODE Beep Beep Beep Beep Beep Cool Wind Ion Mode • Usually, use the product in the Cool Wind Ion Mode. Room Cleaning Mode •...
IG-ETC1A/E CARE AND CLEANING Main unit (Or more often if necessary) Every month Wipe with a dry soft cloth. <For Stubborn Dirt> Use water and a mild detergent. And then, wipe with a wet cloth. Make sure to dry out the main unit.
CARE AND CLEANING Inside of Air trunk Every 6 months (Or more often if necessary) Remove the air suction port cover. Unscrew the coin screws (x2) on the main unit using a coin. Coin screw Note: • Do not lose the screws. Air suction port cover Disconnect the nail (x1) at lower left Press the upper part of...
Page 39
IG-ETC1A/E Vacuum off the dust attached to the air trunk with a vacuum sweeper. • For stubborn dirt, wipe with a dry soft cloth. Attach the air trunk cover and secure the coin screws (x2) on the air trunk cover.
CARE AND CLEANING Plasmacluster Ion Generating Unit (Electrode section) (Or more often if necessary) (When operated 24 hours a day) Every 6 months Remove the dust attached to the electrode section of the unit with an included unit cleaning brush or commercially-available cotton applicator. Remove the air suction port cover.
IG-ETC1A/E PLASMACLUSTER ION GENERATING UNIT REPLACEMENT If the total operating time passes approximately 17,500 hours (approx. 2 years if the product is operated 24 hours a day), Unit Replacing Light À ashes to notify you of the replacement time of the unit.
• The unit holder can be opened by 45 degrees only. If you open if forcibly, it may be damaged. SPECIFICATIONS Model IG-ETC1A/IG-ETC1E Power source system AC Adapter IG-ETC1A: AC 220V, 0.9A, 50Hz Power input IG-ETC1E: AC 220-240V, 0.9A, 50/60Hz Power output DC 12V, 2.5A Applicable À oor area 19.83...
IG-ETC1A/E TROUBLESHOOTING Before calling for service, please review the TROUBLESHOOTING chart below. The problem may not be unit malfunctions. Problem WHAT TO DO [ For Main unit ] The Plasmacluster Ion Generator • Is a AC Adapter inserted properly? Please insert AC Adapter correctly.
Page 44
• Pull out the AC adapter and insert it again in approx. 1 minute, and then operate the product again. • If an error is displayed repeatedly, please contact the store you purchased the product or Sharp Service Centre. E-20...
Need help?
Do you have a question about the IG-ETC1A and is the answer not in the manual?
Questions and answers