SkyLink SC-100 Quick Setup Manual

Daily Operation
Function Keypad Keychain
Command Transmitter
Disarm 000# Button #3
Chime 000A#
Away 000BC Button #1
Sequence
Home 000C Button #2
Sequence
Night 000AB
Sequence
CUSTOMER SERVICE
17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3
+800-304-1187 EST 9:00 to 17:00 (from Monday to Friday)
Fax: +800-286-1320
Email:support@skylinkhome.com (Reply within 24 hrs)
http://www.skylinkhome.com
US Patent D410633, 6243000B1
©2004 SKYLINK GROUP
Remark
Set the system to DISARM from ARM
CHIME
1 2 3 4
DELAY
INSTANT
AC PWR LO BATT. ARM
Set the system to Chime Mode for testing
CHIME
1 2 3 4
DELAY
INSTANT
AC PWR LO BATT. ARM
Arm your system when you are the last person leaving
CHIME
1 2 3 4
DELAY
INSTANT
AC PWR LO BATT. ARM
After 45 seconds:
CHIME
1 2 3 4
DELAY
INSTANT
AC PWR LO BATT. ARM
Arm your system when someone remains
CHIME
1 2 3 4 DELAY
INSTANT
AC PWR LO BATT. ARM
After 45 seconds:
CHIME
1 2 3 4 DELAY
INSTANT
AC PWR LO BATT. ARM
Arm your system when there are people in your house
but no one is expected to enter or exit
CHIME
1 2 3 4 DELAY
INSTANT
AC PWR LO BATT. ARM
102A110
The Complete Alarm System
QUICK SETUP GUIDE
Congratulations!
You have just purchased one of the most reliable and up-to-date wireless security systems on the market today.
We recommended you go through the User's Instructions to fully understand the system and plan your installation. If you
wish to set up the system immediately, please read this guide first.
This quick guide describes the basic steps to install your SC-100 Total Protection Alarm System (control panel, two door/
window sensors, motion sensor and keychain transmitter).
STEP 1
TEST THE COMPONENTS
It is advisable to test the function of each component and the system before they are
mounted to the desired position.
Control Panel
1. Remove the Control Panel from the box.
2. Open the Control Panel by pressing the two tabs on top with the front facing you.
(Diagram 1)
3. Pull open the front.
4. Thread the AC adapter cord through the hole in the back of the unit and plug into
the circuit board as shown. (Diagram 2)
5. Insert the 9 volt alkaline battery. (Diagram 3)
6. Rotate the antenna from the inside position to a vertical position.
7. Close the cover carefully so that the cord and antenna are not cut.
8. Plug in the AC adapter into the power outlet.
The red {ACPWR}light and keypad backlight will go on.
9. Press [0][0][0][A][#] to set the Control Panel to Chime
Mode for testing. The red {ARM} light and all 4 green
lights above the numbers will go on.
Door/Window Sensors
1. Remove the transmitter from the box. Pull out the battery protective strap.
2. Put the magnetic switch and magnet next to each other.
3. Separate the magnetic switch and magnet by more
than 1cm (3/8 inch), you should hear a two-tone chime
from the Control Panel. The green light 1 will flash.
4. The door/window sensor is working. Put the magnetic switch and magnet together.
Motion Sensor
1. Remove the motion sensor from the box.
2. Undo the screw on the back of the motion sensor and remove the cover
of the battery compartment. Connect a 9V alkaline battery to the connector
wire. Then close the battery cover and re-insert the screw. (Diagram 4)
Model SC-100
Diagram 1
Diagram 2
Diagram 3
CHIME
AC Power is
1 2 3 4
DELAY
connected.
INSTANT
AC PWR LO BATT. ARM
CHIME
Press 000# to
1 2 3 4
DELAY
test your system.
INSTANT
AC PWR LO BATT. ARM
CHIME
Separate the
1 2 3 4 DELAY
magnetic contact.
INSTANT
AC PWR LO BATT. ARM
Diagram 4