Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for SkyLink DIAL-ALERT AD-433S
Summary of Contents for SkyLink DIAL-ALERT AD-433S
- Page 1 Emergency Dialer DIAL-ALERT MODEL : AD-433S CUSTOMER SERVICE 17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3 Tel : (800) 304-1187 Fax : (800) 286-1320 PAT. D410633 101A320 JUNE, 2004 Email : support@skylinkhome.com 6243000B1...
- Page 2 SKYLINK TECHNOLOGIES INC. Your Guide to the Emergency Dialer DIAL-ALERT MODEL: AD-433S Emergency Dialer DIAL-ALERT AD-433S USER'S INSTRUCTIONS The AD-433S Emergency Dialer contains all the above items. – –...
-
Page 3: Table Of Contents
PACKAGE CONTENTS TABLE OF CONTENTS All materials required for installation are included with this package PACKAGE CONTENTS....................4 OVERVIEW......................5 1 Dial-Alert (AD-433S) INSTALLATION........................6 1 Telephone Line LIGHTS AND SOUNDS......................9 1 antenna (installed) STANDARD PROGRAMMING...................10-14 1 AC adapter -Program the Time Clock....................10 1 9 volt alkaline battery -Recording a Message....................10... -
Page 4: Overview
The Dial-Alert works in conjunction with Skylink's Security Systems (SC-5, 2. Screw part way into the surface where the holes are marked SC-10, SC-100 series, SC-200 series) and all the Skylink Sensors / Trans mitters. 4. Unscrew the screws and remove the template When the alarm sounds on the control panel on any of our security systems, 5. - Page 5 INSTALLATION INSTALLATION Switch Setting 2. Thread the telephone line through the top hole in the back of the unit and plug it into 1. Tone/Pulse Switch the "LINE" jack. If you want to have an This dialer supports both Tone and Pulse answering machine on the same line as dialing.
-
Page 6: Lights And Sounds
LIGHTS AND SOUNDS STANDARD PROGRAMMING Below is an explanation of the lights and sounds of the Dial-Alert When you plug in the dialer for the first time, you will hear a double beep and all the lights will be on for 2 seconds, the keypad will continue to flash and LIGHTS the clock will be set to 12:00. -
Page 7: Playback Pre-Recorded Message
1. Press the [MEM] key, the display will show a letter “M” on the upper left Cautions: corner. If nothing is entered within 5 seconds, the display will return to Skylink recommends that the telephone or pager numbers of your relatives, the clock mode. neighbors, office/work, friends or doctor be programmed into your Dial-Alert. Do 2. -
Page 8: Storing Telephone Numbers In Memory (Sends The Numeric Information To Pager Only)
STANDARD PROGRAMMING STANDARD PROGRAMMING TO REVIEW OR MODIFY THE PRE-PROGRAMMED PHONE NUM- C. Storing telephone numbers in memory (Sends the numeric BERS, THE REDIAL COUNT AND/OR THE REPEAT TIMES OF A information to pager only) PHONE NUMBER. 1. Press the [MEM] key, the display will show a letter “M” on the upper left corner. -
Page 9: Advanced Programming
ADVANCED PROGRAMMING ADVANCED PROGRAMMING PROGRAM THE CALLING TIME and before you can enter the numeric information (i.e. phone number). The display will show a "P" if a pause period is entered. This pause period is The calling time is the amount of time the phone will ring until the call is dis- factory set at 5 seconds but can be changed from 1 - 9 seconds. -
Page 10: Program The Id Code Of A Transmitter
[7] key . When the dialer is disabled, the display will read “ L 7 2 ”. To program control panel (SC-001, SC-002) to the Dial-Alert (AD-433S): When the dialer is disarmed, the disarm LED light will be on. 1. Press the [L] key, display will show “L”. -
Page 11: Universal Dial Tone
ADVANCED PROGRAMMING ADVANCED PROGRAMMING Entering a premises using the delay dialing When the universal dial tone is turned off, and no dial tone is detected within 1 minute (after the dialer is activated), the display will show “no LInE” and the If entering a premises through a door that is monitored with a door sensor, the backlit keypad will flash. -
Page 12: Connect The Dial-Alert With Your Existing Alarm System
Follow the diagram below for hardwiring the dialer with the existing alarm system. Every time the alarm system is activated, it will automatically trigger the dialer to dial out all the preset telephone numbers and play the pre-recorded message. PANEL OR SENSOR AD-433S N.C.. LATCHING DRY CONTACT* (NORMALLY CLOSED... -
Page 13: Battery Maintenance
BATTERY MAINTENANCE ADDITIONAL ACCESSORIES The AD-433S Dial-Alert comes with 1 battery that at some point you may have Additional sensors and transmitters as well as add on accessories are available to replace: to work with your Dial-Alert. 9 volt alkaline battery for the Dial-Alert... - Page 14 (AA-433) - Notifies Security Control Panel (SC-001) or - Eliminates the need to walk through your premises Emergency Dialer (AD-433S) when water is detected to your Security Systems Control Panel - 12V alkaline battery included - Operates using lithium batteries (included) –...
Need help?
Do you have a question about the DIAL-ALERT AD-433S and is the answer not in the manual?
Questions and answers