Related Manuals for PTN WHD4
Summary of Contents for PTN WHD4
- Page 1 HDMI Selection Switcher 4x1 USER MANUAL WHD4 PTN HDMI Selection Switcher 4x1 Version: WHD42013V1.1 PTN Electronics Limited www.PTN-electronics.com...
- Page 2 Please refer to the dealers for the latest details. This manual is copyright PTN Electronics Limited. All rights reserved. No part of this publication may be copied or reproduced without the prior written consent of PTN Electronics Limited.
-
Page 3: Table Of Contents
HDMI Selection Switcher 4x1 Table of Contents 1. Introduction ....................... 1 1.1. Introduction to WHD4 ..................1 1.2. Package Contents ..................1 2. Features ........................1 3. Specification ......................1 4. Operations of the Control Panel and the Remote Controller ........2 4.1. -
Page 4: Introduction
HDMI Selection Switcher 4x1 1. Introduction 1.1. Introduction to WHD4 WHD4 is a 4x1 selection switcher, which enables easy manual or RS232/infrared remote switching within different HDMI sources. It is a high performance HDMI device with resolution up to 1920*1200@60Hz, 1080p &... -
Page 5: Operations Of The Control Panel And The Remote Controller
4.1. Operations of the Control Panel Name Description ① Auto-sw Switching modes Status indicator. ② Infrared Remote Controller. ③ INPUT HDMI input channels, from 1 to 4. ④ RS232 RS232 control port. ⑤ Power indicator. ⑥ Power interface. PTN Electronics Limited www.PTN-electronics.com... -
Page 6: Operations Of The Remote Controller
Unused F5-3 9HDF 5.2. Connection with Computer Please connect reference to the following contents. 1) Use a RS232 control line to connect the COM1 or COM2 port of the computer to the RS232 interface of WHD4. PTN Electronics Limited www.PTN-electronics.com... -
Page 7: System Diagram
2) Install the serial driver. 3) Run the COM software and check the connecting state. 4) If it’s OK, then we can control WHD4 by sending RS232 command codes. If not, probably the control line is bad contact. 6. System Diagram... -
Page 8: Auto-Switching Function
WHD4 detects the signal from the port input 1 to input 4 one by one. When it detects that input 1 is not available, and then it turns to detect input 2. When it detects that input 2 has a higher priority and it is available, then it will choose input 2 to output. -
Page 9: Panel Drawing
(auto switching mode is our factory default), operations are as below: 1) Button control: a) By pressing key “INPUT 1” for 3 seconds, you can set WHD4 from auto switching mode to manual-switching mode (“Auto-SW” LED will be off). -
Page 10: Communication Protocol And Command Codes
If not the problem mentioned above, probably there is something broken inside the unit, please send it to the dealer for repairing. 5) If the POWER indicator doesn’t work or no respond to any operation, please make PTN Electronics Limited www.PTN-electronics.com... -
Page 11: Safety Operation Guide
DO NOT repair it on your own, in case of accident or increasing the damage of the equipment. 7) DO NOT splash any chemistry substance or liquid in the equipment or around. PTN Electronics Limited www.PTN-electronics.com... -
Page 12: After-Sales Service
HDMI Selection Switcher 4x1 12. After-sales Service 1) If there appear some problems when running WHD4, please check and deal with the problems reference to this user manual. Any transport costs are borne by the users during the warranty. 2) You can email to our after-sales department or make a call, please tell us the following information about your cases.
Need help?
Do you have a question about the WHD4 and is the answer not in the manual?
Questions and answers