DSC Power832PC5010 CP-01 Installation Manual page 32

Option Definition
7 Telephone Line
Monitor
8 Telephone Line
Monitor Audible
Trouble
[016] - FOURTH SYSTEM OPTION CODES
Option Definition
1 AC Trouble Display
2 AC Trouble Flash
3 Keypad Blanking
4 Keypad Blanking
Restore
5 Keypad Backlight-
ing
6 Power Save Mode
7 Bypass Status
Display
8 Keypad Tampers
[017] - FIFTH SYSTEM OPTION CODES
Option Definition
1 Wireless Key
Disarming
2 RF Jam Event Log
Options
On/Off Description
ON Telephone Line Monitor enabled. The TLM function will be active and the system will indicate a
Trouble #3 condition when using the [*][2] View Trouble Conditions command.
OFF Telephone Line Monitor disabled. The TLM function will be shut off and telephone line troubles
will not be indicated by the system.
ON TLM Audible When Armed. When the system is disarmed, a Telephone Line Monitor Trouble will
generate a Trouble indication as described above. If the system is armed, a Telephone Line Monitor
Trouble will generate an audible alarm on the bell or siren for the duration programmed for Bell
Time-out or until an access code is entered to disarm.
OFF TLM Trouble Only. A Telephone Line Trouble will generate a Trouble indication, the Trouble LED will
come ON, and the keypad sounder will beep until a key is pressed.
On/Off Description
ON AC Trouble Displayed. If AC power fails, the condition will be reported to the monitoring station
and will be indicated as a Trouble condition on the system keypads.
OFF AC Trouble Not Displayed. If AC power fails, the condition will be reported, but the Trouble light
will not be indicated on the system keypads. If [*][2] is entered to view the system troubles, Trouble
#2 will still be displayed.
ON Trouble Light Flashes if AC Fails. When AC power is lost from the system, the Trouble light will
flash in the base Ready and Armed mode within 30 seconds after power is lost. When AC restores,
the Trouble light will stop flashing within 30 seconds. If enabled, this option will override the AC dis-
play option.
OFF Trouble Light Does Not Flash on AC Fail.
ON Blank Keypad When Not Used. If no keys are pressed for 30 seconds, all keypad lights except
backlighting (if enabled) will be shut OFF until the next keypress, Entry Delay, Audible Alarm or Key-
pad Buzzer condition.
NOTE: Keypad function keys will still operate when the keypad is blank, unless the func-
tion key is programmed to require an access code.
OFF Keypad Always Active. The keypad lights will remain ON at all times.
ON Access Code Required to remove Keypad Blanking. A valid access code must be entered before
a blanked Keypad can be used
OFF Access Code Not Required. Pressing any key on a blanked keypad will remove the blanking.
ON Keypad Backlighting is Enabled. All keypads on the system will have backlighting on all of the
time.
OFF Keypad Backlighting is Disabled.
ON Power Save Mode Enabled. If AC power fails, all keypad lights including backlighting will be shut
OFF. The keypad lights will come back ON after a keypress, Entry Delay, Audible Alarm or Keypad
Buzzer condition (except Door Chime). The keypad lights will return to the off state after 30 seconds
of keypad inactivity.
OFF Power Save Mode Disabled.
ON Bypass Status Displayed While Armed. The Bypass status light will be ON if there are zones
bypassed when the system is armed.
OFF Bypass Status Not Displayed While Armed. The Bypass light will be ON only while the system is
disarmed to indicate that there are bypassed zones on the system. When the system is armed, the
Bypass light will be OFF.
NOTE: The Bypass status LED will be ON if there are Stay/Away zones auto-bypassed at the
time of arming regardless of whether or not this option is enabled. This option only
enables and disables manual bypass display.
ON Keypad Tampers are Enabled. All keypads containing Tamper switches will generate Tamper
Alarms and Restorals (Sect 338). NOTE: Not used in North America; ensure that it is disabled.
OFF Keypad Tampers are Disabled.
NOTE: If this option is used, all keypads should be properly installed and secured (Tamper
restored) before enabling the option.
On/Off Description
ON WLS Keys Do Not Use Access Codes. The panel will accept the disarm keycode from an unidenti-
fied wireless key, allowing arming/disarming without a code.
NOTE: Wireless keys can only be assigned access codes when used with PC5132 (refer to
the PC5132 Installation Manual for information on programming wireless keys.)
NOTE: This option must be enabled when using a PC5132 v2.1 or earlier.
OFF NOTE: WLS Keys Uses Access Codes. The panel will NOT accept the disarm keycode from an uniden-
tified wireless key. An Access code must be associated with a WLS key for proper operation (refer to the
PC5132 manual for information on programming wireless keys).
NOTE: This option must be ON when using a PC5132 older than v3.00.
ON RF Jam Log After 5 Minutes. The RF Jam Trouble will not log to the event buffer until the 5- minute
delay has elapsed.
OFF RF Jam Log After 30 Seconds. The RF Jam Trouble will log to the event buffer after the initial 30
second delay has elapsed.
WWW.DIYALARMFORUM.COM
26