DSC Power832PC5010 CP-01 Installation Manual page 22

Installer Programming - Codes and Options
There are three codes which can be programmed by the
installer in Installer Programming: the Master Code
Installer Code Installer Code, and a Maintenance Code Installer Code Installer Code Maintenance Code Maintenance Code Maintenance Code. All other access
codes can be programmed through the [*][5] command, as
described previously in this section.
The master code can also be programmed by the user as
access code (40). However, if the Master Code Not Change-
able option is enabled, the Master Code can only be able
able able
changed in Installer programming.
The Maintenance Code can only be used to arm and dis-
arm the system. The Maintenance Code cannot bypass
zones, use [*][9] to arm the system, cancel auto-arming, or
perform [*][7] command functions. There will be no arm/
disarm bell squawks when the Maintenance Code is used.
General access codes can arm and disarm the system.
When the Code Required for Bypassing Code Required for Bypassing Code Required for Bypassing Code Required for Bypassing option is enabled,
users will need to enter a valid access code in order to
bypass zones. Individual access codes can have the Zone
Bypassing attribute
Attribute programming, as described previously in this
section.
Installer Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section [006]
Master Code. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section [007]
Maintenance Code . . . . . . . . . . . . . . . . . . . . . . . . . . Section [008]
Master Code Not Changeable. . . . . . . . . . . . . . . Section [015]: [6]
Code Required for Bypassing . . . . . . . . . . . . . . . Section [015]: [5]
NOTE: Only one partition at a time can use [*][5]
programming.
[*] [6] User Functions
NOTE: Only one partition at a time can use [*][6]
programming.
To program user functions, perform the following:
1. Press [*] [6] [Master Code]. The keypad will flash the
'Program' light.
2. Press the number [1] to [6] for the item to be pro-
grammed.
• [1] - Time and Date [1] - Time and Date
[1] - Time and Date [1] - Time and Date
See the Power Series User Guide for instructions on
setting the time and date ('Setting the Time and Date').
• [2] - Auto-arm Enable/Disable [2] - Auto-arm Enable/Disable [2] - Auto-arm Enable/Disable [2] - Auto-arm Enable/Disable
Enter [2] to enable (three keypad beeps) or disable (one
long beep) the auto-arm feature.
• [3] - Auto-arm Schedule [3] - Auto-arm Schedule [3] - Auto-arm Schedule [3] - Auto-arm Schedule
Enter [3] to change the auto-arm time for each day of
the week.
Scroll to the day of the week you want to change, or
enter the number of the day (1-7 for Sunday to Satur-
day). On an LED keypad, zone lights 1-7 will represent
Sunday to Saturday.
When you have selected a day, enter the auto-arm time
in 24-hr format (i.e., enter a 4-digit number in [hhmm]
format).
The system will return you to the day selection menu.
Scroll to the next day you want to program, or to exit
auto-arm programming, press [#].
NOTE:
To change the Auto-arm schedule at another parti-
tion, users with access to that partition will have to select
the partition on the keypad, before entering the Auto-arm
Schedule menu. See section 4.4 'Global and Partition Key-
pad Operation' for more information.
NOTE: Only PKP-LCD v2.0 or greater keypads support the
[*][6][3] menu option.
• [4] - System Test [4] - System Test
[4] - System Test [4] - System Test
When [4] is pressed the panel will perform the following.
- sound the alarm output for two seconds
- light all lights and display pixels on the keypad
Master Code, the Master Code Master Code
Master Code Not Change- Master Code Not Change- Master Code Not Change-
disabled under Access
WWW.DIYALARMFORUM.COM
- sound the keypad buzzer for two seconds
- test the main panel/PC5200/PC5204 battery
- send a System Test Reporting code, if programmed.
For step-by-step instructions on performing a system test,
see the Power Series User's Guide ('Full System Test').
• [5] - Enable DLS (Downloading) [5] - Enable DLS (Downloading)
[5] - Enable DLS (Downloading) [5] - Enable DLS (Downloading)
When [5] is pressed the panel will turn on the down-
loading option for 6 hours. During this time the panel
will answer incoming downloading calls (see Section
5.7 Downloading Options PWS Sect 7)
• • • • [6] – User-initiated Call-Up [6] – User-initiated Call-Up [6] – User-initiated Call-Up [6] – User-initiated Call-Up
When [6] is pressed, the panel will initiate a call to the
downloading computer.
LCD Keypad User Functions
Additional features are available using on the LCD key-
pad. These features do not have numbers assigned. Use
the arrow keys (< >) to scroll through the [
and press the [
View Event Buffer View Event Buffer: The 256 event buffer can be viewed
View Event Buffer View Event Buffer
Code
through any LCD keypad.
• Brightness Control Brightness Control: When this option is selected the
Brightness Control Brightness Control
keypad will allow you to scroll through 10 different
backlight level options. Use the arrow keys (<>) to
scroll to the desired backlight level and press the [#]
key to exit.
• Contrast Control Contrast Control Contrast Control: When this option is selected the key- Contrast Control
pad will allow you to scroll through 10 different con-
trast level options. Use the arrow keys (<>) to scroll to
the desired contrast level and press the [#] key to exit.
• Keypad Buzzer Control: Keypad Buzzer Control: Keypad Buzzer Control: When this option is selected Keypad Buzzer Control:
the keypad will allow you to scroll through 21 different
keypad sounder tone options. Use the arrow keys (<>)
to scroll to the desired keypad beeper level and press
the [#] key to exit. This function can be achieved on
LED keypads by holding the [*] key.
[*] [7] Command Output Functions
There are four output functions available to the user.
Entering [*] [7] [1-4] [Access Code, if required] will acti-
vate any output programmed for options [19]-[22]
(respectively). Each function can be performed when the
system is either armed or disarmed.
For more information regarding these output types, ( see
Section 5.8 Programmable Output Programming).
[*] [8] Installer Programming
Enter [*][8] followed by the Installer Code to enter
Installer Programming.
[*] [9] Arming Without Entry Delay
When a partition is armed with the [*][9] command the
panel will remove the entry delay from the partition. After
the Exit Delay, Delay 1 and Delay 2 type zones will be
instant and Stay/Away zones will remain bypassed. ( see
section 'Basic Programming PWS Sect 3' ).
For more information regarding this feature, see the Pow-
erSeries User's Guide .
The entry delay can be activated or deactivated at any
time while the system is armed by pressing [*][9].
NOTE: Global Delay zones will always have an entry delay,
even if the system is armed using [*][9].
16
✱
] key to select the following commands.
✱
] [6] menu