1. Manuals
  2. Brands
  3. Pyronix Manuals
  4. Control Panel
  5. STERLING 10
  6. User manual

Pyronix STERLING 10 User Manual

Control panel with remote keypads
Hide thumbs Also See for STERLING 10:
Table of Contents

Advertisement

Quick Links

See also: Installation Manual
STERLING 10
Control Panel with Remote Keypads
USER MANUAL (ICON and LCD)
Pyronix Limited
Pyronix House
Braithwell Way
Hellaby, Rotherham
S66 8QY, UK
www.pyronix.com/installer
IMPORTANT:
Please note the Sterling 10 LCD keypad is not compatible
for use with the Sterling 10 ICON keypad.
RINS415-9

Advertisement

Table of Contents
loading

Related Manuals for Pyronix STERLING 10

Summary of Contents for Pyronix STERLING 10

  • Page 1 Control Panel with Remote Keypads USER MANUAL (ICON and LCD) Pyronix Limited Pyronix House Braithwell Way Hellaby, Rotherham S66 8QY, UK www.pyronix.com/installer IMPORTANT: Please note the Sterling 10 LCD keypad is not compatible for use with the Sterling 10 ICON keypad. RINS415-9...

  • Page 2: Table Of Contents

    CONTENTS 1. INTRODUCTION .............................1 1.1 Sterling 10 LCD Keypad ........................1 1.2 Sterling 10 ICON Keypad ........................2 2. MASTER AND LIMITED USER FUNCTIONS....................3 2.1 Arming The Panel ..........................3 Arming Different Arm Modes .........................3 2.2 Silent Arming The Panel ........................4 2.3 Arming the panel when the Mains Fails ....................4 2.4 Arm with Omits...........................5...

  • Page 3: Introduction

    5. NOTES 1. INTRODUCTION Thank you for buying the Sterling 10 control panel. The Sterling panel uses the latest technology in design and manufacture. As the end user of the Sterling you will have been provided with either an LCD or ICON keypad. This manual is written to help you use the functions of your alarm system, enabling you to get the best out of your system.

  • Page 4: Sterling 10 Icon Keypad

    Where functionality for both keypads is the same, only one set of instructions for both are described. IMPORTANT: Please note the Sterling 10 LCD keypad is not compatible for use with the Sterling 10 ICON keypad. Page: 2 RINS415-9...

  • Page 5: Master And Limited User Functions

    The following operations can be performed by both Master and Limited Users. 2.1 Arming The Panel Situation Label At the time of arming the Sterling 10, any four arm modes can be selected. i.e. SYSTEM DISARMED System Disarmed ARM MODE A: Whole system armed, nobody on premises.

  • Page 6: Silent Arming The Panel

    USER 1 2.2 Silent Arming The Panel STERLING If you wish to silent arm the Sterling 10, so the entry and exit timer is silent: Press the key (on the ICON press the ) then the arm mode you require: P.A.

  • Page 7: Arm With Omits

    2.4 Arm with Omits There are 4 fault conditions automatically detected by the Sterling 10. The user is informed of a fault It is possible to arm the panel with one or more zones omitted (that is, not activated). The sensors for these zones will not activate the alarm system under any circumstances for that arm procedure.

  • Page 8: Duress Arm/Disarm

    Sterling 10 User Manual Sterling 10 User Manual Once entered, the zone that was activated will be displayed (as above). To reset the system, enter Deleting a Limited User Code you user code again, and “SYSTEM DISARMED” will be shown.

  • Page 9: Turning Chime On And Off

    The Sterling 10 control panel incorporates a memory log of the last 100 alarm events and is accessible to both Users and the Engineer. It will record Fire, Intruder, Personal Attack and Tamper ICON Keypad alarms and will also show if any of the 8 alarm zones have been triggered or omitted.
  • Page 10 Sterling 10 User Manual Sterling 10 User Manual Changing the Master Code SYSTEM DISARMED LCD Keypad UNSET USER 1 STERLING Func Press the Enter Then the key and scroll to ‘CHANGE CODES’. Func Press the key to accept. Enter P.A.
  • Page 11 Set Backlight. Changing display user name text. The default master code is 1234. Pyronix recommends that this should be changed as soon as your panel is up and running. Please also note that the Master Code cannot be deleted and is needed to change any other code.

  • Page 12: Master User Only Functions

    Sterling 10 User Manual Sterling 10 User Manual 3. MASTER USER ONLY FUNCTIONS Func Press the key to perform the next test: ‘STROBE TEST’ will then be displayed. Enter Func Press the key to perform the next test: ‘BELL TEST’ will then be displayed.

Table of Contents