Chroma Studio Force D Compact User Manual page 21

To activate the wireless DMX connection between a Compact PSU unit as the Transmitter and the next Compact
PSU unit as the Receiver:
A. Setup the Compact PSU unit as the Receiver unit:
1. From the main menu, scroll and select Wireless
2. In Wireless Wireless, select Receiver
Wireless Wireless
3. Press Enter for 2 seconds to save and display shows Wireless
4. Press Enter, display shows Receiver
5. Press Enter, display shows Unlink frm Trnsm
6. Press Enter, Unlink frm Trnsm Unlink frm Trnsm Unlink frm Trnsm blinks for a few seconds until the display goes back to the previous menu and Unlink frm Trnsm
then the main menu. This will unlink previous signal connections.
Proceed to setup next Compact PSU as the transmitter unit.
B. Setup the Compact PSU as the Transmitter unit:
Connect DMX control to the Compact PSU unit via XLR5 cable.
1. From the main menu, scroll and select Wireless
2. In Wir Wire e e e less Wir Wir less, , , , select Tra less less
3. Press Enter for 2 seconds to save and display will show Wireless
4. Press Enter, display shows Transmitter
5. Press Enter, display shows Add Receivers
6. Press Enter, Add Receivers Add Receivers Add Receivers blinks for a few seconds until the display goes back to the previous menu and then Add Receivers
the main menu. The unit is initiating signal/link search.
Note:
The Compact PSU transmitter unit that is not connected to DMX control console continues to send wireless signal
link to the Compact PSU receiver units.
C. To unlink receivers from the Compact PSU transmitter unit:
From the main menu of the Compact PSU transmitter unit,
1. From the main menu, scroll and select Wireless
2. In Wireless Wireless Wireless Wireless, select Transmitter
3. Press Enter and then select Unlink Receivers
4. Press Enter, Unli Unli Unlink Receivers Unli
then the main menu.
Technical Technical Technical Technical
In this mode, the frequency settings of the unit can be changed, and addressing software for the Compact LED
engines can be uploaded.
1. From the main menu, scroll and select Technical
2. In Technical, select either Frequency
Frequency: Frequency: Frequency: Frequency:
The power supply unit has four frequency settings available - 1200, 2400, 4800, 9600. This allows for the LED
scan rate to be synchronised with the video camera and avoid a flickering effect. Press the Up/Down buttons to
select the desired frequency, press Enter for 2 seconds to save.
Upload Heads: Upload Heads: Upload Heads: Upload Heads:
The LED engine/s addressing software for the Compact fixture can be uploaded to the power supply unit from the
Chroma-Q Uploader:
1. Connect the Compact fixture/s to the PSU.
2. In Technical, select Upload Heads
3. Connect an XLR 5-pin cable from the Uploader to the unit
4. Power-up the Uploader - display shows the file name, and Ready
5. Press the GO GO GO button once to execute the uploading - red indicator light on the GO GO
6. The Uploader display shows a simulated arrow moving from left to right indicating the uploading process
7. The Green LED circuit will light up (low intensity) to indicate completion of a successful Upload and the
Studio Force D/V Compact User Manual
Wireless Wireless Wireless
Receiver
Receiver Receiver
Receiver Receiver Receiver
Unlink frm Trnsm Unlink frm Trnsm Unlink frm Trnsm
Wireless
Wireless Wireless
Tra Transmitter Tra nsmitter nsmitter nsmitter
Transmitter Transmitter Transmitter
Add Receivers
Add Receivers Add Receivers
Wireless
Wireless Wireless
Transmitter Transmitter Transmitter
Unlink Receivers
Unlink Receivers Unlink Receivers
nk Receivers blinks for a few seconds until the display goes back to the previous menu and nk Receivers nk Receivers
Technical
Technical Technical
Frequency Frequency Frequency or Upload Heads Upload Heads Upload Heads Upload Heads
Upload Heads Upload Heads then press Enter, and the display shows Ready Upload Heads
www.chroma-q.com
Wireless Wireless Wireless
Wireless
Wireless Wireless
Ready
Ready Ready
21
Ready Ready Ready
GO button blinks GO GO
V1.7 June 2014