Congratulations on your purchase of this Alcatel Temporis IP product. Before using this Alcatel Temporis IP product, please read Important Safety Information on page 105 of this manual. Please thoroughly read this manual for all the feature operations and troubleshooting information necessary to install and operate your new product. You can also visit our website at alcatel-business.com.
There are two network ports, known as the LAN port and PC port, at the back of the deskset. The LAN port allows the Temporis IP150 deskset to connect to the IP PBX via a router. The PC port is for another device such as a personal computer to connect to the Ethernet network through the deskset.
This telephone supports caller ID with call waiting service. Caller ID services are subscriber services available from many telephone service providers for a fee. The telephone can store up to 200 Call Log entries. The Temporis IP150 IP Phone features include: 2.5-inch backlit Liquid Crystal Display ...
2 to access Line 1, and keys 3 and 4 to access Line 2. Label the keys appropriately for deskset users after configuration. Other possible programmable key settings Directory Call History Redial Messages Temporis IP150 Administration and Provisioning Guide ed 0.1 7/106...
IP Addresses and Connectivity An IP address is an individual numeric identification assigned to devices on a computer network. Valid IP addresses on the same subnet allow devices on the network to identify Temporis IP150 Administration and Provisioning Guide ed 0.1 8/106...
Page 9
PoE, install the phone near a power outlet not controlled by a wall switch. The phone can be placed on a flat surface or vertically mounted on the wall. For customer service or product information, visit our website at alcatel-business.com. Avoid placing the deskset too close to: ...
Figure 1: Temporis IP150 Installation Example Deskset installation To install the phone: 1. If you plan to place the phone on a flat surface, you can use the phone with or without the foot stand depending on the work angle you wish to have. To assemble...
Page 11
1. Put the corded handset aside. Use a coin to rotate the handset tab 180 degrees. The protruding edge holds the corded handset when the phone is mounted on the wall. Temporis IP150 Administration and Provisioning Guide ed 0.1 11/106...
The idle screen indicates that you have no active or held calls. Figure 2: Idle screen Note “Line” softkey will be shown only if you have configured and registered more than one sip account. Temporis IP150 Administration and Provisioning Guide ed 0.1 12/106...
Through the menu, they can customize the screen appearance, sounds, and manage calls. For more information, see the Temporis IP150 User Guide. The Web User Interface, or WebUI, which you access using your Internet browser.
Server Port number Proxy server IP address Proxy server port number Model number 3. Product Info Serial number MAC address Software version Hardware version Temporis IP150 Administration and Provisioning Guide ed 0.1 14/106...
-or- Press 4 (Admin Settings) on the dial pad. 3. Use the dial pad to enter the admin password, the press SELECT. The default password is admin. The Admin Settings are: Temporis IP150 Administration and Provisioning Guide ed 0.1 15/106...
Note: You must be familiar with TCP/IP principles and protocols to configure static IP settings. To set static IP for the deskset: 1. From the Network setting menu, press or to highlight Set static IP, then press SELECT. Temporis IP150 Administration and Provisioning Guide ed 0.1 16/106...
Proxy server port number Line registration Auto/manual answer page To use the Line setting menu: 1. From the Admin Settings menu, press to highlight Line, then press SELECT. Temporis IP150 Administration and Provisioning Guide ed 0.1 17/106...
Page 18
Save—prompts you to reboot the phone and apply the new settings Edit—enables you to edit the setting (appears for the Password setting) Press or to advance to the next character. Temporis IP150 Administration and Provisioning Guide ed 0.1 18/106...
The Network status screen appears. Note: Instead of steps a, b, c you can use the shortcut to Network status (in idle mode press d. On the Network status screen, note the IP Address. Temporis IP150 Administration and Provisioning Guide ed 0.1 19/106...
Each WebUI settings page has a Save button. Click Save to save any changes you have made on the page. During a configuration session, click Save before you move on to the next WebUI page. Temporis IP150 Administration and Provisioning Guide ed 0.1 20/106...
General information about your phone, including model, MAC address, and software version Line Status information about your and SIP account registration Network regarding your phone’s network address and network connection Temporis IP150 Administration and Provisioning Guide ed 0.1 21/106...
(or authentication ID) supplied by your service provider. This sip_account.x.authentication_name is used for authentication with the service provider and in most cases is the same as the User ID. Temporis IP150 Administration and Provisioning Guide ed 0.1 22/106...
Page 23
Temporis IP150 User’s Guide. sip_account.x.share_line_enable Barge-in Enables subscribers to shared 0: Disable lines to “barge in” on active 1: Enable sip_account.x.barge_in_enable calls on other shared lines. Temporis IP150 Administration and Provisioning Guide ed 0.1 23/106...
This separator is used to indicate the start of a new pattern. Can be used to add multiple dialing rules to one pattern edit box. A sample dial plan appears below. Temporis IP150 Administration and Provisioning Guide ed 0.1 24/106...
Page 25
Server port Enter the port number 0-65535 5060 that the registrar server sip_account.x.primary_registration_server_port will use. Expiration Enter the desired 0–65535 3600 registration expiry time in Temporis IP150 Administration and Provisioning Guide ed 0.1 25/106...
Page 26
Server port Enter the port number 0–65535 5060 that the backup outbound proxy server sip_account.x.backup_outbound_proxy_server_port will use. This is usually 5060. Temporis IP150 Administration and Provisioning Guide ed 0.1 26/106...
Page 27
Point (DSCP) value from the Quality of Service setting on your router or switch. sip_account.x.signaling_dscp A 6-bit value is supported. Signaling Settings Setting Description Range Default Local SIP port 0–65535 5060 sip_account.x.local_sip_port Temporis IP150 Administration and Provisioning Guide ed 0.1 27/106...
Page 28
Setting Description PFK available? Paging Enter the paging access code. sip_account.x.access_code_page Call Park Enter the call park access Temporis IP150 Administration and Provisioning Guide ed 0.1 28/106...
Page 29
Call Forward Busy ON sip_account.x.access_code_cfb_on Call Forward Busy OFF sip_account.x.access_code_cfb_off Anonymous Call Block ON sip_account.x.access_code_anonymous_call_block_on Anonymous Call Block OFF sip_account.x.access_code_anonymous_call_block_off Outgoing Call Anonymous ON sip_account.x.access_code_outgoing_call_anonymous_on Outgoing Call Anonymous OFF sip_account.x.access_code_outgoing_call_anonymous_off Call Waiting ON Temporis IP150 Administration and Provisioning Guide ed 0.1 29/106...
Page 30
Direct Call Pick Up Enter the Group Call Pickup code. Dialing the sip_account.x.access_code_direct_call_pickup code enables the user to answer a call ringing at another deskset. Busy Lamp Field Settings Temporis IP150 Administration and Provisioning Guide ed 0.1 30/106...
Page 31
Mailbox ID Enter the uri the phone should use to SIP URI blank subscribe to “message summary” notifications. If empty, Voicemail retrieval access code will be used for this purpose. sip_account.x.mwi_uri Temporis IP150 Administration and Provisioning Guide ed 0.1 31/106...
Page 32
1: enable sip_account.x.music_on_hold_enable hold by the remote party. The interval between tones can be controlled with “Call Hold Reminder tone”, in User Preferences section Temporis IP150 Administration and Provisioning Guide ed 0.1 32/106...
Page 33
Maximum value (secs) Enter the maximum interval the 90-65535 1800 phone is willing to use for sip_account.x.sip_session_timer_max monitoring the session. Temporis IP150 Administration and Provisioning Guide ed 0.1 33/106...
1: enable call_settings.line.x.dnd_enable Incoming Calls Selects whether the phone displays show, reject incoming call information while Do reject call_settings.line.x.dnd_incoming_calls Not Disturb is on. The phone will not ring in either mode. Temporis IP150 Administration and Provisioning Guide ed 0.1 34/106...
Select the number of rings 1-10 before unanswered calls are (rings) call_settings.line.x.cfna_delay forwarded. Enable Missed calls alert Enables or disables missed call 0: disable indication on the phone screen 1: enable call_settings.missed_call_alert_enable Temporis IP150 Administration and Provisioning Guide ed 0.1 35/106...
German it: Italian Portuguese nl: Dutch Phone Language Sets the language that appears on the phone. en: English fr: French user_pref.language es: Spanish de: German it: Italian Portuguese nl: Dutch Temporis IP150 Administration and Provisioning Guide ed 0.1 36/106...
Page 37
If set to “enable”, the waiting call is presented to the user If set to “reject”, the phone will send an error response to the server LCD Contrast Level Sets the contrast for the LCD 1–7 Temporis IP150 Administration and Provisioning Guide ed 0.1 37/106...
Page 38
Sets headset volume. 1-10 user_pref.headset_volume Corded Handset volume Sets handset volume. 10–60 (seconds) user_pref.handset_volume Enable Key beep Enables or disables the beep played 0: disable when a key is pressed. 1: enable user_pref.key_beep_enable Temporis IP150 Administration and Provisioning Guide ed 0.1 38/106...
Programmable Keys Temporis IP150 has 10 dual-function programmable keys. The five keys on the left have a dual-color backlight (orange and green) Keys are numbered top to bottom, and left to right. You can assign up to 20 functions to the programmable keys on the Programmable Keys page.
Page 40
For example, choose Line 1 if you wish to use the Parked Call Retrieval FAC that you entered for account 1. Temporis IP150 Administration and Provisioning Guide ed 0.1 40/106...
Page 41
This function allows the user to switch between the pfk.15.feature = F20 (Lower) default function key group (F1 to F10) and the lower second (F11 to F20). F15 can only be used for this function. Temporis IP150 Administration and Provisioning Guide ed 0.1 41/106...
Page 42
Orange: F11-F20 are active. If user presses the key on the left topmost position, F11 wil be triggered Off: F1-F10 are active. If user presses the key on the left topmost position, F1 wil be triggered Temporis IP150 Administration and Provisioning Guide ed 0.1 42/106...
(x: 0-9) Line The SIP account (line) the phone will use 1: Line 1 to dial the number. 2: Line 2 memory_key.x.line (x: 0-9) Temporis IP150 Administration and Provisioning Guide ed 0.1 43/106...
Your router needs a static IP address for IP masquerading to work. network.nat.public_ip_addr Public SIP port Enter the router port 0-65535 5060 number being used for network.nat.public_sip_port SIP. Temporis IP150 Administration and Provisioning Guide ed 0.1 44/106...
Page 45
Enter the lower limit of the RTP port range. network.nat.public_rtp_port_start Public RTP port range stop Enter the upper limit of 0-65535 19000 the RTP port range. network.nat.public_rtp_port_end Temporis IP150 Administration and Provisioning Guide ed 0.1 45/106...
(x= 1-8) The maximum length of the Internal Ringer Text is 40 characters. Internal Ringer Tone Select the desired ringer from Ringer 1 to – the list. Ringer 10 (1- ringersetting.x.ringer_type (x=1-8) Temporis IP150 Administration and Provisioning Guide ed 0.1 46/106...
Enter the static IP address of the IPv4 blank default gateway (in this case, your router). network.ip.gateway_addr Primary DNS Server If DHCP is disabled or you don’t IPv4 blank wish to use the DHCP-assigned network.ip.dns1 Temporis IP150 Administration and Provisioning Guide ed 0.1 47/106...
7 is the highest priority. Note: Configuring the Quality of Service (QoS) settings for your router or switch is a subject outside the network.vlan.wan.priority scope of this document. Temporis IP150 Administration and Provisioning Guide ed 0.1 48/106...
Page 49
Enables the 802.1X authentication 0:Disabled protocol. This provides the phone 1: Enabled with secure access to the network when an 802.1X compliant authentication server is used. Consult your service provider. network.eapol.enable Temporis IP150 Administration and Provisioning Guide ed 0.1 49/106...
Page 50
Identity Integer string blank network.eapol.identity MD5 Password MD5 password. string blank network.eapol.password Temporis IP150 Administration and Provisioning Guide ed 0.1 50/106...
Local Directory WebUI field Directory file XML tag First Name <DIR_ENTRY_NAME_FIRST> Last Name <DIR_ENTRY_NAME_LAST> Home Number <DIR_ENTRY_NUMBER_HOME> Work Number <DIR_ENTRY_NUMBER_WORK> Mobile Number <DIR_ENTRY_NUMBER_MOBILE> Line <DIR_ENTRY_LINE_NUMBER> Call Block (not on WebUI) <DIR_ENTRY_BLOCK> Ringer Tone <DIR_ENTRY_RINGER> Temporis IP150 Administration and Provisioning Guide ed 0.1 51/106...
Page 52
See next subchapter. Click To… Sort the list by last name. Edit information for an entry View the last page of entries. View the next page of entries. Temporis IP150 Administration and Provisioning Guide ed 0.1 52/106...
Page 53
Sets the line used when you dial this Line 1–2 Line 1 directory entry. Home Number Enter the appropriate names and string blank Work Number numbers in these fields. Mobile Number Temporis IP150 Administration and Provisioning Guide ed 0.1 53/106...
Contacts in the xml file will file.contact.directory.overwrite overwrite existing entries. Click-to-dial (Not in WUI) Enables or disables the 0: Disabled capability to dial a contact 1: Enabled entry by clicking on it in the WUI. provisioning.click_to_dial Temporis IP150 Administration and Provisioning Guide ed 0.1 54/106...
You can import your modified directory file by clicking on “Import” after browsing and selecting it. Directory files are .xml files that have the following tags: Black List WebUI field Black List file XML tag First Name <BLACKLIST_ENTRY_NAME_FIRST> Last Name <BLACKLIST_ENTRY_NAME_LAST> Temporis IP150 Administration and Provisioning Guide ed 0.1 55/106...
The URL must point to an xml file formatted as described above. Contacts in the xml file will file.contact.blacklist.overwrite overwrite existing entries. Temporis IP150 Administration and Provisioning Guide ed 0.1 56/106...
LDAP directory through phone menu or remoteDir.ldap_directory_name programmable key. Server address Enter LDAP server IP string blank address or fqdn. remoteDir.ldap_server_address Server Port Enter remote LDAP server 0-65535 port. Normally 389. remoteDir.ldap_server_port Temporis IP150 Administration and Provisioning Guide ed 0.1 57/106...
Page 58
Enter LDAP attribute the string blank phone should use to display last names. remoteDir.ldap_lastname_attribute Work phone number attribute Enter LDAP attribute the string blank phone should use to display work phone Temporis IP150 Administration and Provisioning Guide ed 0.1 58/106...
Page 59
Lookup for out-call Select to enable or disable 0: disabled queries to the LDAP 1: enabled remote directory while dialing in order to dynamically suggest users remoteDir.ldap_outcall_lookup_enable matching dialled digits. Temporis IP150 Administration and Provisioning Guide ed 0.1 59/106...
Broadsoft Directory On Broadsoft page, you can configure your phone to use a remote Broadsoft directory server. Check with your service provider for more details. Temporis IP150 Administration and Provisioning Guide ed 0.1 60/106...
Page 61
Broadsoft authentication name Enter user name for string Blank authentication in front of Broadsoft directory server. remoteDir.broadsoft_user_name Broadsoft authentication password Enter password for string blank authentication in front of Broadsoft directory server. remoteDir.broadsoft_password Temporis IP150 Administration and Provisioning Guide ed 0.1 61/106...
Call History On Call History page you can review your call log details. Missed, received and dialled calls are shown in separate tables. You can also click-to-call entries in these lists. Temporis IP150 Administration and Provisioning Guide ed 0.1 62/106...
Time and Date Settings Setting Description Range Default Date Format Sets the date format. DD/MM/YY, DD/MM/YY MM/DD/YY, YY/MM/DD time_date.date_format Time Format Sets the clock format. 1: 24 Hour 0: 12 Hour time_date.24hr_clock Temporis IP150 Administration and Provisioning Guide ed 0.1 63/106...
Page 64
Option 42 specifies the NTP server available to the phone. When enabled, the phone obtains the time in the following priority: 1. Option 42 2. NTP Server 3. time_date.ntp_dhcp_option Manual time. Temporis IP150 Administration and Provisioning Guide ed 0.1 64/106...
Page 65
Use DHCP (Option 2/100/101) If Enable Network Time is 1: Enabled selected, tick to use DHCP 0: Disabled to determine the time zone offset. Options 2, 100 and 101 determine time zone information. time_date.timezone_dhcp_option Temporis IP150 Administration and Provisioning Guide ed 0.1 65/106...
Page 66
Manual Time Settings Setting Description Date Select the current year, month, and day. Time Sets the current hour, minute, and second. Click Apply Now to start the phone using the manual time settings. Temporis IP150 Administration and Provisioning Guide ed 0.1 66/106...
On the Manual Firmware Update Settings page, you can prompt the phone to immediately download a new firmware file (if available). To update the firmware immediately from the previously programmed url, click Update Firmware Now. Temporis IP150 Administration and Provisioning Guide ed 0.1 67/106...
Page 68
1. On the Manual Firmware Update page, click Choose File to locate and open the firmware update file. 2. Click Update from File. The phone will update its firmware and restart. Temporis IP150 Administration and Provisioning Guide ed 0.1 68/106...
Network > Basic settings page. Otherwise, enabling DHCP for provisioning will not work. 2. Preconfigured URL—this setting is set on the WebUI and/or the configuration file. After changing any settings on this page, click Save to save them. Temporis IP150 Administration and Provisioning Guide ed 0.1 69/106...
Page 70
URL must be RFC 1738 art.atlinks compliant, as follows: “<schema>://<user>:<password>@ .com <host>:<port>/<url-path>” “<user>:<password>@” may be empty. provisioning.provisioning_server_type provisioning.server_address “<port>” can be omitted if you do provisioning.server_port not need to specify the port number. Temporis IP150 Administration and Provisioning Guide ed 0.1 70/106...
Page 71
The update is applied as part of the reboot provisioning.bootup_check_enable process. Interval (minutes) Sets an interval, 0-65535 in minutes, for 0 means no periodically periodic resync will checking for happen provisioning.resync_time updates. Temporis IP150 Administration and Provisioning Guide ed 0.1 71/106...
Page 72
AES provisioning.crypto_passphrase Encryption. Remote Check Sync If enabled, the 0: Disabled phone will react to (Not in WUI) 1: Enabled a NOTIFY(check- sync) in order to launch automatic provisioning. provisioning.remote_check_sync_enable Temporis IP150 Administration and Provisioning Guide ed 0.1 72/106...
Page 73
However, ensure that you edit the file to remove any unit-specific SIP account settings before applying the file to other units. Reset Configuration To reset the phone to its default configuration: Under Reset Configuration, click Reset. Temporis IP150 Administration and Provisioning Guide ed 0.1 73/106...
To change the admin password: 1. Enter the old password (for a new phone, the default password is admin). 2. Enter and re-enter a new password. 3. Click Save. Temporis IP150 Administration and Provisioning Guide ed 0.1 74/106...
Page 75
2. Enable or Disable Secure Browsing. When enabled, the HTTPS protocol is used, and you must select the HTTPS server port in the next step. 3. Enter the HTTPS server port number. The default setting is 443. Temporis IP150 Administration and Provisioning Guide ed 0.1 75/106...
Only accept trusted TLS certificate When enabled, account x 0: Disabled using TLS will only 1: Enabled sip_account.x.check_trusted_certificate accepted trusted servers Use first TLS Certificate for all accounts When enabled, different 0: Disabled Temporis IP150 Administration and Provisioning Guide ed 0.1 76/106...
Page 77
Enter url to download blank Broadsoft directory file.broadsoft.trusted.certificate Certificate from Only accept trusted Broadsoft certificate When enabled, only 0: Disabled trusted servers can be 1: Enabled used for Broadsoft directory remoteDir.broadsoft_check_certificate Temporis IP150 Administration and Provisioning Guide ed 0.1 77/106...
ERROR: Non-urgent failures—unexpected conditions that won't cause the device to malfunction. WARNING: An indication that an error or critical condition can occur if action is not taken. Temporis IP150 Administration and Provisioning Guide ed 0.1 78/106...
Page 79
To generate a pcap trace press “Start Capture” To stop tracing, press “Stop Capture” To download your capture press “Save to file” Download Log To download a copy of the system logs press “Save log to file” Temporis IP150 Administration and Provisioning Guide ed 0.1 79/106...
General file: <model>.cfg MAC-specific file: <model>_<MAC Address>.cfg Thus, for Temporis IP150 the files would be Temporis_IP150.cfg and Temporis_IP150_<MACAddress>.cfg 3. Check updates. The phone maintains a list of the last loaded provisioning files and their digital signature. The phone compares its current configuration against the files it finds on the provisioning server.
A setting can appear in the general configuration file or the unit configuration file, or both files, or neither file. If a setting appears in both files, the setting that is read last is the one that applies. Temporis IP150 Administration and Provisioning Guide ed 0.1 81/106...
IP150_7465D1161234.cfg file. The MAC-specific configuration file contains settings intended exclusively for that phone. Such settings will include SIP account settings such as display name, user ID, authentication ID, and voicemail mailbox ID. Temporis IP150 Administration and Provisioning Guide ed 0.1 82/106...
Elements in brackets are examples—do not enter the brackets. Enter a 16-character passphrase and the unencrypted configuration file filename (the “infile”) and a name for the encrypted file (“outfile”) that will result. To enable configuration file decryption via WUI: Temporis IP150 Administration and Provisioning Guide ed 0.1 83/106...
Page 84
Note: You must ensure that configuration files are encrypted when enabling AES Encryption. Decrypting an unencrypted file will result in a garbage file that is not processed. This will also be logged as an error in the system log. Temporis IP150 Administration and Provisioning Guide ed 0.1 84/106...
Page 85
Note you can modify Provisioning Server Settings via configuration files; so you could use default settings to perform a first provisioning which rewrites these values to suit your production needs. Temporis IP150 Administration and Provisioning Guide ed 0.1 85/106...
Sends and dials currently displayed/highlighted digits Changes the speed dial directory source Directory Opens the list of available directories Edit Go to entry/group editor EditDial Edits a number stored in a list before dialing Temporis IP150 Administration and Provisioning Guide ed 0.1 86/106...
Page 87
It also finally sets up a transfer. Type Switches between the Directory number types within an entry View Displays a database/list XferCall Displays a list of held calls as a transfer target for the active call Confirm Temporis IP150 Administration and Provisioning Guide ed 0.1 87/106...
Setting Description Range Default sip_account.x.sip_account_enable 0, 1 sip_account.x.display_name Text string Blank sip_account.x.user_id Text string Blank sip_account.x.authentication_name Text string Blank sip_account.x.authentication_password Text string Blank sip_account.x.dial_plan Dial plan Text string section sip_account.x.inter_digit_timeout 1-10 Temporis IP150 Administration and Provisioning Guide ed 0.1 88/106...
Page 89
Text string Blank sip_account.x.access_code_retrieve_voicemail Text string Blank sip_account.x.access_code_dnd_on Text string Blank sip_account.x.access_code_dnd_off Text string Blank sip_account.x.access_code_cfa_on Text string Blank sip_account.x.access_code_cfa_off Text string Blank sip_account.x.access_code_cfna_on Text string Blank sip_account.x.access_code_cfna_off Text string Blank Temporis IP150 Administration and Provisioning Guide ed 0.1 89/106...
Page 90
1800 sip_account.x.dtmf_transport_method Sets the auto, auto transport rfc2832, in- method for band, info- DTMF method signalling. sip_account.x.codec_priority.1 G.711a, G.711u G.711u, G.729, G.726, G.722 sip_account.x.codec_priority.2 Auto, G.711a, G.711a G.711u, G.729, G.726, G.722 Temporis IP150 Administration and Provisioning Guide ed 0.1 90/106...
Setting Description Range Default network.ip.dhcp_enable Indicates whether DHCP is enabled 0, 1 network.ip.dns1 Primary DNS server address IPv4 blank network.ip.dns2 Secondary DNS server address IPv4 blank Temporis IP150 Administration and Provisioning Guide ed 0.1 91/106...
The profile settings follow the format: profile.[element]. These settings are not exported when you manually export the configuration from the phone. Setting Description Range Default profile.admin.password Password for admin string admin profile.user.password Password for user string user Temporis IP150 Administration and Provisioning Guide ed 0.1 92/106...
Server address for string https://art.atli configuration nks.com download provisioning.server_username Authentication string blank username for configuration download provisioning.server_password Authentication string blank password for configuration download provisioning.remote_check_sync_enab Enable provisioning start via NOTIFY check-sync Temporis IP150 Administration and Provisioning Guide ed 0.1 93/106...
Enable NTP server 0, 1 time_date.ntp_server_addr Address of NTP IPv4 or fqdn europe.pool.ntp server .org time_date.ntp_server_update_interval Delay between NTP 1000 server updates, in 4294967295 seconds time_date.timezone_dhcp_option Enable time zone 0, 1 Temporis IP150 Administration and Provisioning Guide ed 0.1 94/106...
"Thursday", "Friday", "Saturday" time_date.daylight_saving_end_hour 00:00 -23:00 02:00 time_date.daylight_saving_amount DST offset in 0–255 minutes “log” Module: Log Settings The log settings control system logging activities. The log settings follow the format: log.element. Temporis IP150 Administration and Provisioning Guide ed 0.1 95/106...
LDAP password String Blank remoteDir.ldap_max_hits LDAP maximum hits 0-65535 remoteDir.ldap_firstname_attribute LDAP first name String Blank attribute remoteDir.ldap_lastname_attribute LDAP last name attribute String Blank remoteDir.ldap_work_number_attributes LDAP work number String Blank attributes Temporis IP150 Administration and Provisioning Guide ed 0.1 96/106...
Sets the http port for the 0-65535 embedded web server web.https_port Sets the https port when https is 0-65535 enabled web.https_enable Sets embedded web server to use 0, 1 the https protocol. Temporis IP150 Administration and Provisioning Guide ed 0.1 97/106...
Target number for String Blank call forward no answer call_settings.account.x.cfna_delay Delay (in # of 1-10 rings) before call is forwarded call_settings.missed_call_alert_enable Enable/disable 0, 1 missed call alert Temporis IP150 Administration and Provisioning Guide ed 0.1 99/106...
The memory key settings configure the dial pad keys for speed dialing pre-programmed phone numbers. When configured, the phone user can press and hold a dial pad key to dial a programmed phone number. Temporis IP150 Administration and Provisioning Guide ed 0.1 100/106...
URL of certificate to be imported for secure provisioning file.ldap.trusted.certificate URL of certificate to be imported for secure LDAP file.broadsoft.trusted.certificate URL of certificate to be imported for secure Broadsoft directory Temporis IP150 Administration and Provisioning Guide ed 0.1 101/106...
Page 103
"2 480 -180 620 -180 0 0 0 0 500 500 65535" tone.busy_tone.element.[2-5] blank tone.ring_back_tone.num_of_elements tone.ring_back_tone.element.1 "2 440 -180 480 -180 0 0 0 0 2000 4000 65535" tone.ring_back_tone.element.[2-5] blank Appendix B: Time Zones Temporis IP150 Administration and Provisioning Guide ed 0.1 103/106...
Page 104
If the telephone should fall into water, DO NOT RETRIEVE IT UNTIL YOU UNPLUG THE POWER CORD AND NETWORK CABLE FROM THE WALL, then pull the unit out by the unplugged cords. Temporis IP150 Administration and Provisioning Guide ed 0.1 104/106...
The prongs are not designed to hold the plug in place if it is plugged into a ceiling, an under-the-table or cabinet outlet. Caution: Use only the original power adapter for this product. To obtain it, check with your authorized distributor or reseller. SAVE THESE INSTRUCTIONS Temporis IP150 Administration and Provisioning Guide ed 0.1 105/106...
WEEE separately. European Warranty GPL License Information Portions of the software associated with this product are open source, and fall within the scope of the GNU General Public License (GPL). Temporis IP150 Administration and Provisioning Guide ed 0.1 106/106...