Playing Back A Cd - JVC UX-G6 Service Manual

Continued
5
The tuned station in step 1 is now stored in the
Preset Station
preset channel selected in step 3.
You are possibly not allowed to use the feature until
the station presetting completes.
In some cases, test frequencies have been already
memorized for the system since the factory examined
the preset station features before shipment. This is
not a malfunction.
Presetting Stations
To preset stations automatically — Auto Preset
You can preset up to 30 FM and 15 AM stations into memory
You can automatically preset 30 FM, 15 AM stations. Preset
by following two methods: manual/automatic presettings.
numbers will be allocated as stations are found, starting from
the lowest frequency and moving up to the higher frequency.
• There is a time limit in doing the following steps. If the
setting is canceled before you finish, start from step 1
On the remote control only:
again.
1
Press FM/AM button to select a desired band.
To preset stations manually — Manual Preset
2
1
Press 4 / ¢ (lower/higher frequencies) button Press and hold AUTO PRESET button on the
remote control for more than two seconds.
to tune in the desired station manually.
The system automatically starts searching for stations
with the strong signals continuously, and they are stored
successively into memory as follows:
2
Press SET button.
"SET" appears in the display window for a while (not
blinking).
• Note that "SET" message disappears, presetting
procedure is cancelled.
3
Rotate MULTI JOG dial or press repeatedly UP/
DOWN button to select the preset channel numbered
from 1 to 30 on FM, or 1 to 15 on AM.
To change the FM reception mode
• Note that the selected channel "02" disappears,
• When an FM stereo broadcast is hard to receive or noisy,
presetting procedure is cancelled.
press FM MODE button on the remote control so that
4
MONO indicator lights in the display window. Reception
Press SET button again.
improves.
"STORED" appears in the display window for a
• To restore the stereo effect, press FM MODE button
while.
again so that STEREO indicator lights in the display
window.
In this stereo mode, you can hear stereo sounds when a
program is broadcast in stereo.
15
Continued
4
Press 6 (play/pause) button on the CD unit.
To go to another track
Before or during playback, press 4 / ¢ button
Each track of the CD starts playing one after another,
and stops when the final track has finished playing.
repeatedly:
Press ¢ button:
• To stop playing back for a moment, press 6
Press 4 button:
(play/pause) button on the CD unit.
The playback time starts blinking in the display
window.
Rotating MULTI JOG dial clockwise also changes the tracks
forwards quickly, while rotating it counterclockwise the
tracks reverses quickly.
• To resume playback, press 6 (play/pause)
button again.
Playback continues from the point where it was
stopped for a while.
5
Programing the Playing Order of the Tracks
Press 7 (stop) button to stop playing back the CD.
Following information for the CD appears in the display — Program Play
window.
You can arrange the order in which the tracks play before
you start playback. You can program up to 32 tracks.
1
Total track number
Place a CD.
Total playback time
• If the current playing source is not the CD, press
6
Press 0 (open/close) button on the CD unit to
remove the CD.
• Pressing 0 (open/close) button during playback
2
Press PLAY MODE button repeatedly until "CD
directly, the CD unit stops playback and opens CD
PROGRAM" appears in the display window.
tray.
Searching and Skipping Tracks
• Each time you press the button, playback mode
While playing back a CD, you can do the following
operations.
To search and skip to a particular point in a track
During playback, press and hold 4 / ¢ button to meet
the desired passages in a track:
3
Rotate MULTI JOG dial to select a track number to
Press and hold or ¢ button:
be programed (< / > buttons also available).
Fast forwards in the track.
Press and hold or 4 button:
Fast reverses in the track.
UP/DOWN button on the remote control is also
available to searching operations.
17
Storing a new station on an used channel
erases the previously stored one.
«
«
«
When you unplug the AC power cord
or if a power failure occurs
The preset stations will be erased in a few days.
If this happens, preset the stations again.
Skips to the beginning of the next and succeeding
tracks.
Goes back to the beginning of the current and
previous tracks.
< / > button on the remote control is also available
to skipping operations.
6 (play/pause) button on the CD unit, then 7
(stop) button before going to the next step.
indicators also change as follows:
PROGRAM RANDOM
Canceled
(Normal play)
Track number
Program number

Playing Back a CD

BASS TREBLE FM MODE
PLAY MODE
DISPLAY
PLAY MODE REPEAT AUTO PRESET
REPEAT
TITTLE/EDIT ENTER
DISPLAY SET
CANCEL
/CHARA.
CANCEL
UP
< >
UP/DOWN
SET
DOWN
MD AUX < / >
TAPE CD CD 6 (play/pause)
FM/AM E R T E R
4 / ¢
7 (stop)
VOLUME
6 (play/pause)
You can use Normal, Program, Random, or Repeat Play.
• When using the buttons behind the sliding panel, press
OPEN/CLOSE button on the AX-UXG6 to open the
sliding panel first.
• When using the remote control, press CD 6 (play/
pause) button first and 7 (stop) button successively.
Playing Back the Entire Disc — Normal Play
3
Press 0 (open/close) button again.
The disc tray closes while the information appears
one after another as follows.
1
Press 0 (open/close) button on CD unit.
The system automatically turns on and the disc tray
comes out.
2
Place a disc correctly on the circle of the disc tray,
with its label side up.
• When closing the tray without a CD placed, "CD NO
Good No Good
• When using a CD single (8 cm), place it on the
inner circle of the disc tray.
4
To erase all the programed data
Press SET button to program the track number.
After playing back the CD, you can erase all the programed
track data by pressing 7 (stop) button. New program can
be entered again.
To exit from the Program play mode
Track number
Program number Before or during playback, you can exit from Program play
mode as follows:
Here the track number 2 on the CD is stored into a • Before playback, press PLAY MODE button twice.
• During playback, press 7 (stop) button then PLAY MODE
program number 1, and shortly after that the total
playback time of programed tracks appears in the display
window as follows:
Playback mode indicator goes off and the system resumes
Normal play mode.
Total playback time
5
Repeat steps 3 to 4 to program other tracks you
want up to 32 tracks.
• If you try to program a 33rd step
"MEMORY FULL" will appear in the display
window, and your entry is ignored.
• The total playback time of programed tracks
exceeds 99'59"
"– – : – –" will appear in the display window.
6
Press 6 (play/pause) button on the CD unit.
The programed tracks are played back in the order you
have set.
• Other CD operations are the same as Normal play.
7
Press 7 (stop) button to quit the Program play.
• When Program play finished, CD unit automatically
stops.
To check the program contents
Before playing back the CD, you can check the program
contents by using 4 / ¢ button.
Press ¢ button:
Shows the programed tracks in the programed
order.
Press 4 button:
Shows them in the reverse order.
To modify the program
Before playing back the CD, you can erase the last
programed track by pressing CANCEL button. Each time
you press the button, the last programed track is erased from
the end of program.
• To add new tracks to the program before you start
playing-back, simply select a track number again you
want to add (repeat steps 3 to 4).
UX-G6/FS-G6
Buttons behind the sliding panel
PLAY REC TITLE CLOCK
4 ¢
/CHARA. SET CANCEL ENTER MODE MODE /EDIT /TIMER
4 ¢
CANCEL
SET PLAY MODE
0 (open/close)
STANDBY/ON
M I C R O C O M P O N E N T
FM/AM
MULTI JOG MOS - FET
7 (stop)
Playback mode
MULTI JOG
indicators
• DO NOT try to open or close the CD tray by
hands as it will be damaged.
• DO NOT place any foreign matters.
• DO NOT prevent the tray from opening and
closing, because it may results damages on the
unit.
«
«
Total track number
Total playback time
DISC" appears.
When pressing 6 6 (play/pause) button directly, 6 6 6
the system starts playback a CD immediately.
16
Continued
button twice.
Pressing 0 0 0 0 0 (open/close) button to open the CD
tray also quits and erases the program play.
18
1-11