Brbk-304 Dv Card; Brbk-Hsd2 Hd/Sd-Sdi Output Card; Brbk-Sa1 Analog Sd Output Card - Sony BRC Series System Manual

5.3.12 BRBK-304 DV Card

1
i.LINK (DV) OUT connector
1
5.3.13 BRBK-HSD2 HD/SD-SDI
Output Card
1 2
MONITOR 1
BRBK-HSD2
SDI OUT
SDI MONITOR OUT connector (BNC type)
1
Outputs down-converted SD-SDI signals that
conform to SMPTE 259M serial digital interface
standards, and down-converted HD-SDI signals
that conform to SMPTE 292 serial digital
interface standards.
SDI connectors 1, 2 (BNC type)
2
Outputs down-converted SD-SDI signals that
conform to SMPTE 259M serial digital interface
standards, and down-converted HD-SDI signals
that conform to SMPTE 292 serial digital
interface standards.
Panel switch
3
Switch between SD-SDI signals and HD-SDI
signals.
Note • SD-SDI and HD-SDI signals cannot be supplied
simultaneously.
• Set the panel switch before turning on the
camera.
Images when menu display is ON
When a BRBK-HSD2 is installed in the BRC-
H900 card slot
BRBK-HSD2 panel MONITOR
switch connector
Left position HD/
DATA MIX: ON
(HD-SDI output)
Middle position
HD/DATA MIX: OFF
(HD-SDI output)
Right position SD
(SD-SDI output)
: Menu is superimposed on image
×: Menu is not superimposed on image
(i.LINK 6-pin)
3
2
OFF
ON
HD SD
SDI connectors 1, 2
When a BRBK-HSD2 is installed in the BRU-
SF10 card slot
BRBK-HSD2 panel MONITOR
switch connector
Left position HD/
DATA MIX: ON
(HD-SDI output)
Middle position
HD/DATA MIX: OFF
(HD-SDI output)
Right position SD
(SD-SDI output)
: Menu is superimposed on image
×: Menu is not superimposed on image
1) When the DATA MIX switch on the front panel of the
BRU-SF10 HD Optical Multiplex Unit is set to ON, the menu
display is overlapped on all images output from the card.
When the DATA MIX switch is set to OFF, the menu is not
displayed.
5.3.14 BRBK-SA1 Analog SD
Output Card
1 2
BRBK-SA1
VIDEO S-VIDEO
VIDEO connector (BNC type)
1
Supplies analog composite signals. The aspect
ratio can be configured in the SD menu of the
camera.
S VIDEO connector (4-pin mini-DIN)
2
Outputs S-Video signals. You can configure the
aspect ratio with the SD menu of the camera.
RGB/SYNC connector (D-sub 9-pin)
3
Pin No. Signal
1 GND
2
GND
3 R/Cr
4 G/ Y
5 B/Cb
Note • When a BRBK-SA1 Analog SD Output Card is
installed in the BRC-H900 HD Color Video
Camera and menu display for the camera is
turned ON, the menu display is overlapped with
the image.
• When a BRBK-SA1 Analog SD Output Card is
installed in a BRU-SF10 HD Optical Multiplex Unit
on which the front panel DATA MIX switch is set
to ON and menu display for the camera is
turned ON, the menu display is overlapped with
the image. When the DATA MIX switch is set to
OFF, the menu will not be displayed on the
image, even if menu display for the camera is
turned ON.
SDI connectors 1,
2
/
1)
3
RGB/SYNC
Pin No. Signal
6 Composite/Y
7
SYNC
8 GND
9 -/C
27
Location and Function of Parts