Advertisement
Clean the filter regularly. If the filter is heavily stained and does not clean, or if it is damaged, replace the filter with a new filter.
Otherwise, dirt may get inside and appear on the screen, preventing you from fully enjoying the video image. If dirt gets inside
or if you need information about the filter, consult authorized dealer where you purchased the projector or the nearest Service
Center.
1
After the projector goes into stand-by state with the STAND BY indicator on, turn off the MAIN POWER switch and pull
out the power cord from the projector and the wall outlet.
2
Loosen the screw with a flat-end screwdriver.
• The screw is fitted so that it does not come off the filter.
• If the filter is clogged with dirt, etc., the projector goes into an warning state (the OPERATE and STAND BY indicator blink.
etc.). Therefore regularly, clean the filter. For the warning indication, refer to page 65.
3
Clean the filter with a neutral detergent, wash it in water, and then dry it in the shade.
• Put on rubber gloves when using neutral detergent.
• After you have washed the filter in water, make sure the filter is completely dry before reinstalling it, otherwise an electric
shock or malfunction could occur.
• Do not clean the filter using a vacuum cleaner. Since the filter is soft, it may be sucked into the vacuum cleaner or damaged.
4
Fasten the screw with a flat-end screwdriver.
• Install the filter correctly. Otherwise, the projector does not operate. (Goes into an warning state (For the warning indication,
Refer to page 64).)
• If the filter's claws (in particular the claw which is hidden behind the filter cover knob) are damaged, the projector may not
operate. Then, replace with a new filter.
Solutions to common problems related to your projector are described here. If none of the solutions presented here solves the
problem, unplug the projector and consult an authorized dealer or Service Center.
• Is the power cord disconnected?
• Is the MAIN POWER switch turned
on?
• Is the fuse blown?
• Is the lamp-replacement opening cover
closed correctly?
• Is the filter closed correctly?
• Has the lamp life expired? (Has the
lamp use time reached 1000 hours?)
• Is the lens cap removed?
• Is the lamp life near its end?
• Is the air intake or exhaust area
blocked?
• Is the correct input selected?
• Are devices connected correctly?
• Are signals being supplied from the
connected devices?
• Are input signals (scanning frequency,
etc.) appropriate?
• Is the correct color system selected?
• Is brightness adjusted correctly?
• Is video turned off by pressing the
HIDE button?
• Is focus adjusted correctly?
• Is distance too short or too long?
• Are Tracking and Phase adjusted
correctly?
• Is picture quality (Brightness, etc.)
adjusted correctly?
• Was the FREEZE button on the
remote control pressed?
• Was the DIGITAL ZOOM T button on
the remote control pressed?
• Insert the power cord (plug) firmly.
30
• Turn on the MAIN POWER switch.
31
• Turn off the MAIN POWER switch and
56
check the fuse.
If it is blown, replace it
• Turn off the MAIN POWER switch, close
7, 31, 57
the lamp-replacement opening cover
correctly, and turn on the MAIN POWER
switch again.
• Turn off the MAIN POWER switch, fit the
7, 31, 61
filter correctly, and turn on the MAIN
POWER switch again.
• Turn off the MAIN POWER switch, replace
31, 57,
60
with a new light-source lamp, and turn on
the MAIN POWER switch.
Reset the lamp use time after replacing with
a new lamp.
• Remove the lens cap.
30
• Check the lamp use time on the menu, and
55, 57
if the lamp life is near its end, arrange for a
replacement lamp, or replace a little earlier.
• Turn off the MAIN POWER switch, remove
6, 7, 31
any blocking objects, and turn on the MAIN
POWER switch again.
• Select the correct input with the VIDEO and
9, 13
PC buttons.
• Connect devices correctly.
11, 22
• Set connected devices correctly.
–
• Check if the signal is appropriate (scanning
22, 23
frequency, etc.) and input the appropriate
signal.
• Set the color system to AUTO or to the
44
correct dedicated color system.
• Adjust brightness on the menu.
48
• Press the HIDE button to turn video on.
10, 12,
34
• Adjust focus.
12, 33
• Set the projector at the correct distance.
18, 19
• If satisfactory results are not obtained by
13, 35,
pressing the QUICK ALIGN. button to
46
conduct quick alignment, adjust Tracking
and Phase on the menu.
• Adjust picture quality on the menu.
48
• Press the FREEZE button to release
12, 36
freezing.
• Press the PRESET button to restore the
12, 36
original video screen.
Advertisement
