Advertisement
I
Main Menu in PC Menu Mode (While receiving computer-related signals)
Image adj. → (Refer to page 48)
Brightness:
Brightness of the picture image being projected can be adjusted. (–30 to +30, 0*)
Contrast:
Contrast of the picture image being projected can be adjusted. (–30 to +30, 0*)
Sharpness:
Adjust the outline of letters etc. (1 / 2 / 3 / 4 / 5, 3*)
All reset:
Resets above items to the factory set values.
Yes / No
Setting
Tracking:
The lateral size and display area of picture image can be adjusted. (–128 to +127)
→ (Refer to page 46)
Flickering or dim picture image can be adjusted. (0 to 31) → (Refer to page 46)
Phase:
Video screen position and menu position can be adjusted. → (Refer to page 50)
Position:
Disp. Posi. / Menu
Resize:
The relationship between the number of pixels (resolution) and the screen can be selected.
→ (Refer to page 52)
"1:1":
Picture image is projected with its original size.
Panel:
Picture image is enlarged to the full size.
Aspect*:
Picture image is enlarged while maintaining the original aspect ratio.
Clamp
Selectable clamp position. Normally, set to "BP". ST / FP / BP*
Color temp.
Color temp.:
Adjustable color temperature, Low/Middle* /High.
Will be adjusted to correct reddish or blueish image.
R-Gain:
Adjusts the red level. (o to 255, the adjustable range varies depending on signals)
G-Gain:
Adjusts the green level. (o to 255, the adjustable range varies depending on signals)
B-Gain:
Adjusts the blue level. (o to 255, the adjustable range varies depending on signals)
All-reset:
Reset above items to the factory set values.
Yes/No
Options → (Refer to page 53)
Options 1
Menu display: 15sec* (Menu disappears in 15 seconds.) / ON (Menu stays on.)
Line display:
5sec* (Line display such as "PC1" or "PC2" appears on top right of the screen for 5 seconds
when the VIDEO or PC button is pressed.) / OFF (Line display does not appear.)
Keystone:
Press ENTER to enter the Keystone submenu.
Keystone:
Adjust to correct the trapezoidal distortion of the projected image.
(–80 to +128, 0*)
PC2 (BNC):
RGB or YP
P
*. Set to RGB when a computer device with analog RGB, V, H/Cs signals is
B
R
connected to the PC2 terminals. Set to YP
Y, R-Y) or DTV-format signals (Y, P
Options 2:
Press ENTER to enter the "Option 2" submenu.
Right Left rev.:
OFF* / ON (Select for upside-down hanging on the ceiling.)
Top Bottom inv.:
OFF* / ON (Select for upside-down hanging on the ceiling.)
RS-232C [bps]:
Selectable baud rate (transmission speed). 9600 / 19200*
Sleep time [min:]
Selectable sleep times. If no-signal condition continues for the period
of selected time (Unite: Minutes), the projector enters the stand-by
mode. 15 / 30 / 60 / OFF*
Options 1:
Press ENTER to return to the "Option 1" submenu.
Language for on-screen display. → (Refer to page 45)
Language
Japanese / English* / German / Spanish / Italian / French
Information → (Refer to page 55)
Input:
Shows the terminal name selected by the PC button. (PC1or PC2)
Switcher:
This display currently has no meaning. ("CH.0" is usually displayed to indicate that it is not being used.)
Shows the resolution of the input signal being received. (Horizontal × Vertical)
Resolution:
It may not be displayed correctly with some input signals.
Frequency H: Shows the horizontal frequency of the input signal being received. (
Frequency V: Shows the vertical frequency of the input signal being received. (
Lamp time:
Accumulated used hours of the light-source lamp.
P
when a device with component signals (Y, B-
B
R
, P
) are connected to the PC2 terminals.
B
R
kHz)
Hz)
When the MENU button is pressed, the projector enters Video or PC menu mode by responding to the input signal being
received.
Enters this mode when video-device-related signals are
input from the following devices.
• Video devices connected to the VIDEO IN (Y/C and
VIDEO) terminals.
• A video device connected to the PC 2 terminals, which
outputs component signals (Y, B-Y, R-Y) or DTV-format
signals (Y, P
, P
).
B
R
Enters this mode when computer-related signals are input
from the following devices.
• A computer connected to the PC 1 terminal.
• A computer connected to the PC 2 terminal, which outputs
analog RGB, V, H/Cs signals.
1
The main menu is displayed on the screen.
2
5
∞ ∞ ∞ ∞
3
3 3 3 3
The submenu corresponding to the item selected in step
2 is displayed on the screen.
4
5
∞ ∞ ∞ ∞
When a "Language" has been selected in step 2, press
to set the language.
5
2 2 2 2
3 3 3 3
When an item which has the "ENTER" message has been
selected in step 4, press the ENTER button to move to the
next submenu.
→ (Refer to page 48)
• All reset
→ (Refer to page 50)
• Position
→ (Refer to page 44)
• Decoder
→ (Refer to page 53)
• Keystone
• Options 1 → (Refer to page 53)
• Options 2 → (Refer to page 53)
• While the main menu is displayed, press the MENU button.
The main menu disappears and the original picture image
resumes.
• While the submenu is displayed, press the EXIT button.
The menu returns to the previous menu.
• To exit the menu mode directly, press the MENU button.
The submenu disappears and the original video image is
restored.
Advertisement
