The model and serial numbers will be found on a decal attached to the pressure washer. You should record both serial number and date of purchase and keep in a safe place for future reference. Shark BR 97-723 • REV. 5/07...
4. All installations must comply with local codes. result. Contact your electrician, plumber, utility company Do not spray water on or near or the selling distributor for specific details. electrical components. kEEp WaTER SpRay aWay fRoM ElECTRICal WIRINg. Shark BR 97-723 • REV. 5/07...
Page 5
Do not direct discharge stream at people, or severe in- RISk of INjECTIoN oR SEvERE INjURy jury or death will result. To pERSoNS. kEEp ClEaR of NozzlE. 13. Never make adjustments on machine while in op- eration. Shark BR 97-723 • REV. 5/07...
2 minutes, water will leak from valve. Warm detergent Injector — Allows you to siphon and mix water will discharge from pump protector onto floor. detergents (not shown). This system prevents internal pump damage. Shark BR 97-723 • REV. 5/07...
Use 30 wt. non detergent oil. garden hose pump Water Inlet STEp 7: Check inlet filters, remove debris, then connect garden hose to pump water inlet. CAuTION: Do not run the pump without water or pump damage will result. Shark BR 97-723 • REV. 5/07...
When the engine is not in use, leave the fuel valve in choke knob in). Push the choke knob to the "Closed" the "OFF" position. position. To restart a warm engine, leave the choke knob in the "Open" position. Shark BR 97-723 • REV. 5/07...
NoTE: For a more gentle rinse, select the white 40° or green 25° nozzle. To scour the surface, select the yellow 15° or red 0° nozzle. To apply detergent select the black nozzle. Shark BR 97-723 • REV. 5/07...
Select and install the washer in low pressure for 1-2 minutes. desired high pressure nozzle. NoTE: You can also stop detergent from flowing by simply removing detergent siphon hose from bottle. Shark BR 97-723 • REV. 5/07...
NoTE: Refer to the 3. Pour about one teaspoon of engine oil through engine manufacturer's manual for service and mainte- the spark plug hole, pull the starter grip several nance of the engine. Shark BR 97-723 • REV. 5/07...
Water sprayed at machine Change oil. Direct spray away from ma- IN pUMp oIl chine. High humidity in air Check and change oil twice as often. Piston packing worn. Oil seal Call technical support. worn Shark BR 97-723 • REV. 5/07...
Page 14
IS NoISy Pump is sucking air Check that hoses and fittings are air tight. Turn off machine and purge pump by squeezing trigger gun until a steady flow of water emerges through nozzle. Shark BR 97-723 • REV. 5/07...
Check pump oil and engine oil level before first use of your new pressure washer. Estimated operating Estimated operating date oil Changes date oil Changes hours Since last oil hours Since last oil Month/day/year Month/day/year Change Change Shark BR 97-723 • REV. 5/07...
Page 25
7, 8 37, 38, 39 37, 38, 39 INCLUDED 38, 39 NUMBER OF CYLINDERS KIT WILL SERVICE * For GM 4035H High Heat Packings, Use 70-261212 **For GM 4035H High Heat Packings, Use 70-261213 Shark BR 97-723 • REV. 5/07...
Page 27
37, 38, 37, 38, NUMBERS 6, 7, 8 6, 7, 8 INCLUDED 39, 40 39, 40 NUMBER OF CYLINDERS KIT WILL SERVICE * High Heat, Use 70-262922 GT-5030H/R ** High Heat, Use 70-262921 GT-5030H/R Shark BR 97-723 • REV. 5/07...
UNloadER ExplodEd vIEW aNd paRTS lIST aR - al 607 #9.802-367.0 7-8 gpm, 4200 psi Shark BR 97-723 • REV. 5/07...
Page 31
If spike pressure exceeds the 500 psi limit, remove the adjusting knob (Item 8) and re-adjust (lower) the nuts (Items 25) on the stem (Item 14). Re-attach the adjusting knob (Item 8), then repeat step #6. Shark BR 97-723 • REV. 5/07...
Page 32
*Kit : 10.3072.01* O-Ring, 1.78 x 20.35 mm 60.1615.24 VB280-350.4 Spare Parts Kit 60.0973.31 Piston Housing (60.1600.00) Pcs. 11 x 1 60.1805.31 Piston Housing (60.1700.00) 16.2100.00 M 4 x 4 mm Dowel 60.1728.31 Lock Nut Shark BR 97-723 • REV. 5/07...
PARTICULAR PURPOSE. SHARK does not authorize any other party, including authorized Dealers, to make any representa- tion or promise on behalf of SHARK, or to modify the terms, conditions, or limitations in any way. It is the buyer’s responsibility to ensure that the installation and use of SHARK products conforms to local codes. While SHARK attempts to assure that its products meet national codes, it cannot be responsible for how the customer chooses to use or install the product.
Page 36
Form #97-723 / 8.914-453.0 • Revised 5/07 • Printed in U.S.A.
Need help?
Do you have a question about the BR-304037 and is the answer not in the manual?
Questions and answers