Daikin Super Multi Plus E-Series Service Manual page 272

Ceiling Mounted Cassette Type
5. Name and function of each switch and display
on the remote control
Refer to figure 1 on page [1]
ON/OFF BUTTON
Press the button and the system will start.
1
Press the button again and the system will
stop.
OPERATION LAMP (RED)
2
The lamp lights up during operation.
DISPLAY "
IZED CONTROL)
3
When this display shows, the system is
UNDER CENTRALIZED CONTROL.
DISPLAY "
(VENTILATION/AIR CLEANING)
4
This display shows that the total heat
exchange and the air cleaning unit are in
operation (These are optional accessories).
DISPLAY " " "
(OPERATION MODE)
5
This display shows the current OPERATION
MODE. For cooling only type, "
and " " (Heating) are not installed.
DISPLAY " TEST " (INSPECTION/TEST
OPERATION)
6
When the INSPECTION/TEST OPERATION
BUTTON is pressed, the display shows the
system mode is in.
DISPLAY "
7
This display shows the PROGRAMMED TIME
of the system start or stop.
DISPLAY "
8
This display shows the set temperature.
DISPLAY "
9
This display shows the set fan speed.
DISPLAY"
10
Refer to "AIR FLOW DIRECTION ADJUST".
DISPLAY "
11 FILTER)
Refer to "HOW TO CLEAN THE AIR FILTER".
DISPLAY "
12
Refer to "DEFROST OPERATION".
NON-FUNCTIONING DISPLAY
If that particular function is not available,
pressing the button may display the words
"NOT AVAILABLE" for a few seconds.When
13
running multiple units simultaneously, the
"NOT AVAILABLE" message will only appear
if none of the indoor units is equipped with
the function. If even one unit is equipped with
the function, the display will not appear.
TIMER MODE START/STOP BUTTON
14
Refer to "PROGRAM TIMER OPERATION".
260
" (UNDER CENTRAL-
" " " " " " "
" " " " " " "
" (Auto)
" (PROGRAMMED TIME)
" (SET TEMPERATURE)
" (FAN SPEED)
" (AIR FLOW FLAP)
" (TIME TO CLEAN AIR
" (DEFROST)
TIMER ON/OFF BUTTON
15
Refer to "PROGRAM TIMER OPERATION".
INSPECTION/TEST OPERATION BUT-
TON
16
This button is used only by qualified service
persons for maintenance purposes.
PROGRAMMING TIME BUTTON
17
Use this button for programming "START
and/or STOP" time.
TEMPERATURE SETTING BUTTON
18
Use this button for SETTING TEMPERA-
TURE.
FILTER SIGN RESET BUTTON
19
Refer to "HOW TO CLEAN THE AIR FILTER".
FAN SPEED CONTROL BUTTON
20
Press this button to select the fan speed,
HIGH or LOW, of your choice.
OPERATION MODE SELECTOR BUTTON
21
Press this button to select OPERATION MODE.
AIR FLOW DIRECTION ADJUST BUTTON
22
Refer to "AIR FLOW DIRECTION ADJUST".
NOTE
• For the sake of explanation, all indications are
shown on the display in figure 1 contrary to
actual running situations.
6. Operation procedure
Refer to figure 1 on page [1]
• Operating procedure varies with heat pump type and
cooling only type. Contact your Daikin dealer to confirm
your system type.
• To protect the unit, turn on the main power switch 6 hours
before operation.
• If the main power supply is turned off during operation,
operation will restart automatically after the power turns
back on again.
Cooling, heating, automatic, fan, and program dry
operation
Operate in the following order.
1
Operation mode selector
Press OPERATION MODE SELECTOR button several
times and select the OPERATION MODE of your choice as
follows.
COOLING OPERATION............................"
HEATING OPERATION .........................."
AUTOMATIC OPERATION ....................."
• In this operation mode, COOL/HEAT changeover is
automatically conducted.
SiEN18-622
"
"
"
System Configuration