Section 6 Adjustment Procedures; Preparation - Icom IC-F6061 Service Manual

SECTION 6 SECTION 6

6-1 PREPARATION

When adjusting IC-F6060 series, CS-F5060
OPC-1122/U/ and the following test equipments are required.
JIG CABLE
EQUIPMENT
Output voltage
DC power supply
Current capacity
Frequency range
modulation analyzer
Measuring range
Frequency range
Frequency counter Frequency accuracy
Sensitivity
Measuring range
RF power meter Frequency range
Impedance
SWR
▄ SYSTEM REQUIREMENTS
® ®
• Microsoft Windows 98/98SE/Me/2000/XP
▄ ADJUSTMENT SOFTWARE INSTALLATION
q Quit all applications when Windows is running.
w Insert the CD into the appropriate CD drive.
e Double-click the "Setup.exe" contained in the 'CS-F5060
ADJ' folder in the CD drive.
r The "Welcome to the InstallShield Wizard for CS-F5060
ADJ" will appear. Click [Next>].
t The "Choose Destination Location" will appear. Then click
[Next>] to install the software to the destination folder. (e.g.
C:\Program Files\Icom\CS-F5060 ADJ)
y After the installation is completed, the "InstallShield Wiz-
ard Complete" will appear. Then click [Finish].
u Eject the CD.
i Program group 'CS-F5060 ADJ' appears in the 'Programs'
folder of the start menu, and 'CS-F5060 ADJ' icon ap-
pears on the desk top screen.
▄ BEFORE STARTING SOFTWARE ADJUSTMENT
Clone the adjustment frequencies and settings into the transceiver, and set the confi guration using the CS-F5060
before starting the software adjustment. Otherwise, the software adjustment can not be started.
WARE
CAUTION!: BACK UP the originally programmed memory data in the transceiver before programming the adjustment frequencies.
When program the adjustment frequencies into the transceiver, the transceiver's memory data will be overwritten and
lose original memory data at the same time.
• ADJUSTMENT FREQUENCY LIST
FREQUENCY (MHz)
CH
‡
(Low) (High)
1 400.000 450 .000
2 435 .000 485 .000
3 434.95 .000 484.95 .000
4 470 .000 520 .000
5 435 .000 485 .000
6 435 .000 485 .000
7 435 .000 485 .000
8 400 .000 450 .000
‡
;(Low)=[USA-01], [EXP-01], [EUR-01] (High)=[USA-02], [EXP-02]
*; [EUR] only
ADJUSTMENT PROCEDURES
CLONING SOFTWARE,
GRADE AND RANGE
: 13.6 V DC [USA],[EXP]
13.2 V DC [EUR]
: More than 20 A
: DC–600 MHz
: 0 to ±10 kHz
: 0.1–600 MHz
: ±1 ppm or better
: 100 mV or better
: 0.1–50 W [USA],[EXP]
0.1–30 W [EUR]
: 100–800 MHz
: 50 Ω
: Better than 1.2 : 1
(for the ADJUSTMENT SOFTWARE)
• RS-232C serial port (D-sub 9 pin) or USB port
SETTING
‡
• TX power : Low1
• Mode : Narrow
• TX power : Low1
• Mode : Narrow
• TX power : Low1
• Mode : Narrow
• TX power : Low1
• Mode : Narrow
• TX power : High
• Mode : Narrow
• TX power : Low2
• Mode : Narrow
• TX power : Low1
• Mode : Wide
• TX power : Low1
• Mode : Wide
CS-F5060 ADJ
ADJUSTMENT SOFTWARE
EQUIPMENT
Attenuator
External speaker
Standard signal
generator (SSG)
Oscilloscope
Digital voltmeter
▄ STARTING SOFTWARE ADJUSTMENT
q Connect the transceiver and PC with OPC-1122/U
CABLE .
w Turn the transceiver power ON.
e Boot up Windows, and click the program group 'CS-F5060
ADJ' in the 'Programs' folder of the [Start] menu, then
CS-F5060 ADJ's window appears.
r Click 'Connect' on the CS-F5060 ADJ's window, then the
window shows transceiver's condition and adjustment
items as below.
t Set or modify adjustment data as specifi ed.
Microsoft and Windows are registered trademarks of Micro-
soft Corporation in the U.S.A. and other countries.
FREQUENCY (MHz)
CH
‡
Low band High band
9 470 .000 520 .000
10 435 .000 485 .000
11 400 .000 450 .000
12 470 .000 520 .000
13 435 .000 485 .000
14 400 .000 450 .000
15 470 .000 520 .000
16 435 .000 485 .000
6 - 1
(Rev. 1.0 or later),
GRADE AND RANGE
Power attenuation : 50 or 60 dB
Capacity : 50 W [USA],[EXP)
30 W [EUR]
: 4 Ω
Input impedance
Capacity : 5 W or more
: 0.1–600 MHz
Frequency range
: 0.1 µV to 32 mV
Output level
(–127 to –17 dBm)
Frequency rang : DC–20 MHz
Measuring range : 0.01–20 V
Input impedance : 50 kΩ
Measuring range : 0.1–10V
SETTING
‡
• TX power : Low1
• Mode : Wide
• TX power : Low1
• Mode : Middle
• TX power : High
• Mode : Middle
• TX power : Low1
• Mode : Middle
• TX power : Low1
• Mode : Digital
• TX power : Low1
• Mode : Digital
• TX power : Low1
• Mode : Digital
• TX power : Low1
• Mode : Wide
• CTCSS : 151.4 Hz
JIG
CLONING SOFT-