Advertisement
Quick Links
2100P E
statE
B
roadcast
ASSEMBLY and OPERATING INSTRUCTIONS
PLEASE CALL IF YOU ARE MISSING ANY PARTS, HAVE ANY DIFFICULTY IN ASSEMBLY, OR HAVE ANY QUESTIONS
REGARDING THE SAFE OPERATION OF THIS SPREADER. THIS MODEL INCLUDES LIFETIME TECHNICAL SUPPORT
SUPPORT HOT LINE: 574-848-7491 or 800-294-0671,
HELPFUL HINTS:
; If your spreader does not spread evenly, be sure the FRONT on the gear box points to the front of the spreader. The
impeller must turn clockwise. Reversing the gearbox will cause the impeller to turn counter clockwise. Clean the impeller
plate after each use. Fertilizer stuck on the impeller blades will cause uneven spreading.
; Your spreader is designed to be pushed at three miles per hour, which is a brisk walking speed. Slower or faster speeds
will change the spread patterns. Wet fertilizer will also change the spread pattern and flow rate. Clean and dry your
spreader thoroughly after each use. A coating of light spray oil will help prevent corrosion. Wash between the shut off
plate and bottom of the hopper.
; Gears are permanently lubricated at the factory. Do not open the gearbox or dirt may enter.
Lower
Housing Clip
Axle
Bearing
Bushing
#12 x 1¼"
Flat Head Screw
¼-20
Axle
Lock Nut
Washer
Agitator
¼-20
#10 x ⅝"
Hex Nut
Screw
1. Remove and identify all loose parts from carton
(Qty 4) #31105
#12 X 1¼"
Flat Head Screw
s
PrEadEr
READ THE DIRECTIONS BEFORE ASSEMBLY
⅛ x ¾"
⅛ x 1¼"
Cotter Pin
Cotter Pin
Cotter Pin
Axle
¼-20 x
¼-20 x 1¾"
1½" Bolt
Carriage Bolt
¼-20 x
1¼" Bolt
¼-20 x
2" Bolt
.
2. Position the Hopper on its top as shown
to the left. Install frame using (4) #12 x
1¼" Flat Head Phillips screws. TIGHTEN
THESE NOW - use care to not over tighten
Earth Way
:
@
Email
tEchsuPPort
Earthway
⅛ x 1¾"
CONTROL
ASSEMBLY
FRAME
IMPELLER
EV-N-SPRED
.
com
UPPER HANDLE
ASSEMBLY
DRAW BAR
&
BRACE ASSEMBLY
GEARBOX
AXLE
10-18 Pt# 52159
®
PAGE 1
Advertisement
Related Manuals for EarthWay 2100P Estate
Summary of Contents for EarthWay 2100P Estate
- Page 1 SUPPORT HOT LINE: 574-848-7491 or 800-294-0671, Email tEchsuPPort Earthway HELPFUL HINTS: READ THE DIRECTIONS BEFORE ASSEMBLY ; If your spreader does not spread evenly, be sure the FRONT on the gear box points to the front of the spreader. The impeller must turn clockwise.
- Page 2 Pinion Shaft SLIDE ⅛ x 1¼” Impeller Cotter Pin Gearbox FRONT Gearbox Assembly 3. Install impeller onto pinion shaft. Insert 1/8”x 1¼” Cotter pin through impeller then through pinion shaft. Use hole closest to the gear box. Spread cotter pin to prevent from falling out. Axle Bearing 4.
- Page 3 1¾” Cotter Pin ¾” Cotter Pin Bushing Gearbox & Axle Drawbar Frame Brace Flat Washer 7. Slide axle bushing over axle and into axle bearing to both sides as shown. 8. Install drive wheel to axle using pin hole nearest to lower handles as shown. Insert 1¾” Cotter pin through wheel and through axle.
- Page 4 11. Install Upper Handle between Draw Bars. Insert ¼-20 x 1½” bolts through Draw Bar and Upper Handle and secure with ¼-20 Lock Nuts. TIGHTEN BOLTS AND NUTS NOW. ¼-20 x 1¾” Carriage Bolt ¼-20 Hex 12. Install Control Assembly onto Upper Handle by sliding the Control Assembly over Upper Handle shaft then securing with ¼-20 x 1¾”...
-
Page 5: Year Limited Warranty
5-YEAR LIMITED WARRANTY EarthWay Products, Inc. warrants this product to be free of defects in original workmanship and materials for a period of 5-Years to the end user with the original purchase receipt. If a manufacturing non-conformance is found, EarthWay Products, Inc. - Page 6 EarthWay Products, Inc. P.O. Box 547 Bristol, IN 46507 77001 Phone: 800-294-0671 OPTIONAL www.earthway.com Heavy-Duty Rain Cover 40002 OPTIONAL Debris Screen 2100P Broadcast Spreader ~ Parts List Key # Part # Description Key # Part # Description 60332 HOPPER ASSEMBLY 33106 1/8"...