Table of Contents
Advertisement
Quick Links
T T i i g g e e r r 4 4 0 0 0 0
A radio-controlled model is not a toy and is not intended for persons under 16 years old. Keep
this kit out of the reach of younger children, as it contains parts that could be dangerous. A radio-
controlled model is capable of causing serious bodily injury and property damage. It is the buyer's
responsibility to assemble this aircraft correctly and to properly install the motor, radio, and all other
equipment. Test and fly the finished model only in the presence and with the assistance of another
experienced R/C flyer. The model must always be operated and flown using great care and common
sense, as well as in accordance with the Safety Code of the Academy of Model Aeronautics (5151
Memorial Drive, Muncie, IN 47302, 1-800-435-9262). We suggest you join the AMA and become prop-
erly insured prior to flying this model. Also, consult with the AMA or your local hobby dealer to find an
experienced instructor in your area. Per the Federal Communications Commission, you are required
to use only those radio frequencies specified "for Model Aircraft."
Carl Goldberg Products, Ltd. has inspected and certified the components of this aircraft. The company urges the buyer to perform
his own inspection, prior to assembly, and to immediately request a replacement of any parts he believes to be defective for their
intended use. The company warrants replacement of any such components, provided the buyer requests such replacement with-
in a period of 90 days from the date of purchase and provided the defective part is returned, if so requested by the company.
No other warranty, expressed or implied, is made by the company with respect to this kit. The buyer acknowledges and under-
stands that it is his responsibility to carefully assemble the finished flying model airplane and to fly it safely. The buyer hereby
assumes full responsibility for the risk and all liability for personal or property damage or injury arising out of the buyer's use of the
components of this kit.
CARL GOLDBERG PRODUCTS, LTD.
P.O. Box 88 Oakwood GA 30566 Phone #678-450-0085 Fax # 770-532-2163 www.carlgoldbergproducts.com
WARNING
LIMITED WARRANTY
1
Advertisement
Table of Contents
Related Manuals for Carl Goldberg Products Tiger 400
Summary of Contents for Carl Goldberg Products Tiger 400
- Page 1 LIMITED WARRANTY Carl Goldberg Products, Ltd. has inspected and certified the components of this aircraft. The company urges the buyer to perform his own inspection, prior to assembly, and to immediately request a replacement of any parts he believes to be defective for their intended use.
-
Page 2: Preparing For Assembly
COVERING Before you begin assembling your Tiger 400 ARF, take The Tiger 400 ARF is covered in a premium polyester film some time to read through this entire instruction book. It is chosen by many of the world's top flyers for its beauty, designed to take you step-by-step through the process and toughness, and ease of application and repair. - Page 3 ITEMS NEEDED TO COMPLETE THIS AIRCRAFT Caution: RADIO GUIDANCE SYSTEM (4 CHANNEL MINIMUM REQUIRED WITH 4 SERVOS) 6” SERVO “Y” HARNESS ELECTRONIC SPEED CONTROL Before starting, care- (ELECTRIC FLY C-20 FROM GREAT PLANES SUGGESTED) fully go over all high NIMH 8C 1100AAA BATTERY (2 OR 3 CELL 1500 MAH LI-PO BATTERY SUGGESTED) MINI- PUSHROD CONNECTORS stress areas with an...
- Page 4 Wing Installing Ailerons Aileron Servos Collect the following parts: Collect the following parts: (1) Wing (1) Wing (2) Ailerons ( Left & Right) (2) Servo with hardware (6) Mini CA hinges (2) Aileron pushrod (2) Mini pushrod connectors (Not Included) (2) Single Keepers (2) Adjustable Horn Brackets Mount the aileron servo using the hardware...
-
Page 5: Elevator Installation
Fuselage Stabilizer Collect the following parts: (1) Fuselage (1) Stabilizer & Elevator (1) wing with mounting screws and washers “X” “X” Measure from the end of the wing to the tip of the stab. This measurement should be the same for both sides. Locate the holes in the center of the wing for the wing bolts. -
Page 6: Rudder & Control Horn
Place the fin back on to the fuselage and make sure that there is no gap between the fuselage top and the fin. Place a 90 degree triangle on the top of the stabilizer up against the fin. When you are satisfied with the fit, epoxy the fin to the top of the fuselage and stabilizer. -
Page 7: Landing Gear
Landing Gear Collect the following parts: (1) Fuselage (1) Main Landing Gear Wire (1) Wood Landing Gear Holder Place one half of the motor mount under the motor. Slide the motor towards the firewall till the back of the propeller is approximately 1/2” away from the front from the fuselage. -
Page 8: Installing Wheels
Your model should balance at 2-1/8” to 2-3/8” back from the leading edge of the wing. Start with the controls movements at the following: Ailerons 1/4” up and down Elevator 1/4” up and down Rudder 1/4” up and down You might want to change these throws after you are comfortable flying the Tiger 400.