Installation Instructions - Gliderol Glidermatic GRD Installation Instructions And Owner's Manual

Installation Instructions
These instructions are to be read in conjunction with
Gliderol Roller Door installation instructions.
Please note:-
T H E F O L L O W I N G I N S T R U C T I O N S
F O R F I X I N G O F T H E D R I V E
U N I T A S S E M B L Y
T O T H E D O O R A R E F O R A R I G H T H A N D
INSTALLATION
. (Refer to Fig 1-8)
a) Check the door U bolt is securely tiqhtened on the LEFT
h a n d s i d e o f d o o r
b) Raise the door and tie a rope around the centre to secure
the roll
c) Support the right hand end of the door wjth a suitable
prop, e.g. step ladder and soft padding to protect the door
surface (Fig 2)
STOP WARNING:- DO NOT ALLOW CHTLDREN/PERSONS
A R O U N D T H E D O O R W H E N P R O P P E D .
S E R I O U S P E R S O N A L
INJURY AND/OR PROPERTY DAMAGE CAN RESULT FROM
FAILURE TO FOLLOW THIS WARNING.
d) Carefully loosen and remove the right hand axle U bolt
e) Make sure the door supporting prop is secure. While the
door is supported remove the right hand wall mount
bracket. (Fig 3)
Check if
' U ' B o l t i s
tightened
Fig. 2
Remove
Right
' U ' B o l t
Remove
Right
Bracket
Support
(Ladder)
f) Remove the geared motor (27) and motor spacer (2g) from
the packaging material. Align the spacer over the three
motor mounting holes and insert the motor assembly
between the spoke sections of the drum wheel. Alion the
assembly with the three counter sunk holes in the soore
i&L-rcnl-Affiffilih scTeits ilpptied 3 X (6i25mm counier
n /
sunk) using an appropriate flat bladed screwdriver .(Ensure
the motor assembly is securely fixed to the drum wheel
before proceeding)
Remove the motor shaft screw and slide on the main drive
gear (1 0) , refit the shaft screw and tighten.
S l i d e t h e S l i p R i n g a s s e m b l y ( 6 , 7 , 8 ) o v e r t h e d o o r a x r e ,
locate into a position where the two Slip Ring wires are
closest to the motor . Connect the two wires from the Slip
Ring assembly to the motor leads. Observe the polarity of
E!^ 1
the four wires i.e. red to red black to black.
rtg J
Three boss mounts on the drum wheel will locate the Slip
R i n g a s s e m b l y . U s i n g t h e t h r e e s e l f t a p p i n g s c r e w s
provided securely fix into position (8 5/3).
S l i d e t h e M a i n R i n g G e a r ( 3 2 ) o v e r t h e d o o r a x l e a n d
engage teeth with the motor drive qear.
j)
k) Slide main body (2) over door axle, make sure the manual
release pin (23) is in manual position. locate contact
b r u s h e s ( 2 5 ) i n t o i n n e r a n d o u i e r s l i p r i n g ( 7 , 8 )
l ) T h e M a i n B o d y s h o u l d n o w b e s i t t i n g f l u s h u p a g a i n s t t h e
Ring Gear. Attach Split Ring (9) to Slip Ring extrusion and
secure split ring self tapping screw. (6 3/B)
m) Replace right hand side wall mount bracket (Fig. a)
n) Remove support from door and rest axle carefully on wall
m o u n t i n g b r a c k e t .
- __ -__^-:
s)
Remove
Support
(Ladder)
Release Rope
Retighten
' U ' B o l t
Ref it
R i g h t
j e'ictet
GRD OWNERS MANUAL PAGE 2
DGLIDEROL
L.ZGARAGE DOORS
Fig. 4