Courtesy Lamp - Gliderol Glidermatic GRD Installation Instructions And Owner's Manual

Key Ring Handset
The hand transmitter is manufactured using the latest surface
mount technology and incorporates 3 functional buttons.
This enables the user to remotely control up to 3 separate
operators from the one handset" The soft touch silicon
buttons have been irnpregnated
with a " night glow" material
for easier visibility.
Alarm Closure
lf an attempt is made to force open the door from a closed
position. The Glidermatic Controller will Pulse operate the
door to the fully closed position.
Remote switeh
A simple Bell Press type momentary switch can be hard wired
directly to the control board.
ACCESSORY OPTIONS
With the installation of a small accessory board the
G l i d e r m a t r c C o n t r o l l e r c a n p e r f o r m t h e f o l l o w i n g
functions:-
External Light
This accessory option will allow the connection of auxiliary
lighting ie drive way lighting, internal garage lights.
NB: Max. Load 100W
IWARNING All mains lighting must be fitted by a
qualified Electrician / Personnel
External Counter
For cemmercial applisatlons an electroryc e=o=,unte-r.
(for
door operations ) can be used for warranty verification.
LocalAlarm
A Piezo Alarm Siren can be fitted as a local intruder alert.
This will be activated if an attempt is made to force open
the door from the fully closed position. ln conjunction the
door will perform an Alarm Closure *.
T?ris output can also be wired into an existing home
alarm systern.
* Alarm closui'e as above.
External LED Indicator"
An LED panel is fitted within the house (hard wired ) to
show the status of the door ie open or closed.
OPERATING
cCINTRaLS ffig. 9)
1) Control Box Push Button
Pressing this button will open, close or stop the door.
2) Hand transmitter
Nominally for a single door installation only the large
elliptical button is programmed to operate the door, a
momentary press of this button will open , close, or
stoo the door.
Note: The standard Glidermatic handset has three f ully
functional and independent buttons. Thrs allows the
handsei to operate up to three opeilers in the Gliderol
series ie F,ciler Llcr:r" Cpenr:r, (GRD) Tiir. arrC Secticnal
Opener, (GTS) and the Comnrandoor 2 Gate Opener.
GRD OWNERS MANUAL PAGE 7
INTERNAL CONTROLS / CONNECTIONS
3) Courtesy Lamp
This is a 9 Watt 24VDC Globe which is turned on after
each activation of the Control Box. The illumination
period is approximately 60 seconds.
4)
Obstruction Detection (overload)
Thrs adjustment pot allows you to increase or
decrease the amount force required on a moving
door to register an overload condition.
5) Fuse
This is an automotive blade tvoe fuse.
15A (Blue)
6) Operation Switch ( During Set Up Only )
This PCB mounted switch will allow you to operate
the controller whilst the front cover has been
removed, enabling you to complete the set up
adlustments and test the unit.
7) Internal Pigzo Buzzer ( enable/disable )
The Piezo Buzzer is factory set in the enabled mode.
To disable remove the jumper pin (as shown in
diagram 9)
B) Code Learning
This button is used to store and delete transmitter(s)
from the on board memory.
The memory will allow up to a maximum of 10
handsets to be,,recorded,
lf more than 10 handsets are learnt the FIFO ( First In
First Out ) system applres ie first code learnt will be
deleted and renlarpd hv thp latest rode learnt.
8a) Learn LED lndicator
9) Automatic Close
O Posrtron Auto - Close disabled.
'1
Auto Close enabled 5 sec. delay
2 Auto Close enabled 1 5 sec. delay
3 Auto Close enabled 20 sec. delay
4 Auto Close enabled 30 sec. delay
5 Auto Close enableci 40 sec. delay
6 Auto Close enabled 50 sec. delay
7 Auto CIose enabled 60 sec. delav
Please Note :
Trme delay will start once the door has fully opened
GLIDEROT
GARAEaDooRi
e