Wincor Nixdorf BEETLE User Manual
All-in-one pos system
Hide thumbs
Also See for BEETLE:
- User manual (76 pages) ,
- Installation manual (60 pages) ,
- Operating manual (40 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Wincor Nixdorf BEETLE
Summary of Contents for Wincor Nixdorf BEETLE
- Page 1 BEETLE /iPOS plus All-in-one POS System User Manual...
- Page 2 Please send us a copy of this page if you have any constructive criticism. We would like to thank you in advance for your comments. With kind regards, Your opinion: Wincor Nixdorf International GmbH Technical Documentation R&D SAT36 Wohlrabedamm 31 D-13629 Berlin E-Mail: retail.documentation@wincor-nixdorf.com...
- Page 3 BEETLE /iPOS plus All-in-one POS System User Manual Edition August 2013...
- Page 4 All brand and product names mentioned in this document are trademarks of their respective owners. Copyright © Wincor Nixdorf International GmbH, 2013 The reproduction, transmission or use of this document or its contents is not permitted without express authority. Offenders will be liable for damages.
-
Page 5: Table Of Contents
Important Notes ................1 Safety Notes ..................2 Introduction ................... 4 About This Manual ................4 Care of the BEETLE /iPOS plus ............5 Recycling the BEETLE /iPOS plus ............5 Warranty .................... 6 Before Switching On the System ............ 7 Unpacking and Checking the System .......... - Page 6 Connector Panels System Unit ............. 22 Jack Plug 3.5 mm (OUT) ............... 23 RJ12 (CASHDR) ................23 RJ45 (LAN) ..................23 USB (Universal Serial Bus)- A ............24 P-USB (Powered USB) 12V ............24 CRT ....................24 D- Sub- Jack Power Supplied (COM1*/COM2*) ......24 Disconnecting Cables ..............
- Page 7 Main Menu ..................52 System Date [XX/XX/XXXX] ............52 System Time [XX: XX: XX]............. 52 Advanced Menu ................52 Sub Menu ACPI Settings ............53 Sub Menu RTC Wake Settings ..........53 Wake-on Modes ................54 Sub Menu CPU Configuration ..........54 Sub Menu ...
- Page 8 Test Points Codes ................66 Checkpoint Ranges ................66 SEC Phase ..................66 PEI Phase ..................67 PEI Beep Codes ................69 DXE Phase..................70 DXE Beep Codes ................72 Abbreviations ................73...
-
Page 9: Manufacturer´s Certification
Make sure that only cables and devices may be connected which are admitted by Wincor Nixdorf. The user is responsible for any malfunctions that emerge from the actions mentioned before. -
Page 10: Safety Notes
Never touch any terminal pins of the strip conductors on such compo- nents. Safety Notes The BEETLE /iPOS plus conforms to the current safety standards for data processing equipment. If this device is taken from a cold environment into the operating ... - Page 11 Customer Service of Wincor Nixdorf or your dealer must be notified. Your BEETLE system is the result of modern technical innovation. So please see for according structural and technical surroundings to guar- antee a faultless and efficient work of your BEETLE.
-
Page 12: Introduction
Introduction The BEETLE /iPOS plus is an all-in-one POS system which combines an easy to maintain and modern design with multi-functionality. The powerful system fulfils all the modern technical and environment- friendly standards that are required today. The open architecture of the system makes it possible to use different operating systems of Windows and Linux. -
Page 13: Care Of The Beetle /Ipos Plus
Care of the BEETLE /iPOS plus Clean your BEETLE /iPOS plus housing at regular intervals with a dry, lint- free cloth. If this does not suffice please use a suitable plastic-surface cleaner which you can order from Wincor Nixdorf International GmbH. -
Page 14: Warranty
All parts of the product which are subject to wear and tear are not included in the warranty engagement. For detailed warranty arrangements please consult your contract documents. Please order spare parts at the Wincor Nixdorf customer service. BEETLE /iPOS plus User Manual... -
Page 15: Before Switching On The System
Should you notice any transport damages or discrepancies between pack- age contents and delivery ticket or functional defects please inform your contracting parties or the branch office of Wincor Nixdorf immediately. Please indicate the number of your delivery ticket and delivery ticket position and serial numbers of the respective devices. -
Page 16: Basic Settings
Transport the device only in its original packaging (to protect it against impact and shock). Basic Settings Ex works, the BEETLE /iPOS plus is configured to your order. Additional peripheral devices are delivered separately, for example the swipe card reader. The modules must still be mounted to the system. -
Page 17: Setting Up The Device
VESA-mounting. Set up the BEETLE /iPOS plus system where it will not be exposed to extreme environmental conditions. Protect the device from vibrations, dust, moisture, heat and strong magnetic fields. - Page 18 Permitted range of vision Position the screen within a 0° preferred and permit ted range of vision, so that you 40° can look onto the screen 30° from above. 30° Preferred range of vision BEETLE /iPOS plus User Manual...
-
Page 19: Overview
Overview Front Side View: Wall Fastening Display Brightness adjustment, LEDs Power button Waiter lock (optional) Swipecard reader (optional) BEETLE /iPOS plus User Manual... -
Page 20: Front Side View: Device With Monitor Stand
Front Side View: Device with Monitor Stand ⑥ Display Pedestal Brightness adjustment, LEDs Power button Waiter lock (optional) Swipecard reader (optional) ⑥ BEETLE /iPOS plus User Manual... -
Page 21: Back Side View
Back Side View Module waiter lock/swipecard reader (optional) Pedestal Customer display (optional) BEETLE /iPOS plus User Manual... -
Page 22: Ac Power Adapter
Power Connector DC Power Out, Current Supply to BEETLE /iPOS plus The external power supply is applicable for common line voltage. It automatically adjusts itself to the particular voltage (for grid input voltage and power supply see appendix). -
Page 23: Projected Capacitive Touch Screen
With a circular motion of the fingers the element on the dis- play can be rotated. This function must be supported by either the operating system or by the application. BEETLE /iPOS plus User Manual... -
Page 24: Brightness
The LEDs are at the bottom of the display with the following meaning: hard disk power LED lights white Network connected read and write access to LED flashes white HDD/SSD HDD/SSD Power LED lights white The device is switched on BEETLE /iPOS plus User Manual... -
Page 25: Cleaning Instructions
Use a soft, fine-meshed cloth to clean the surface. Dampen the cloth slightly and then clean the screen. A wrong maintenance may cause damages to the screen, which are not covered by warranty. BEETLE /iPOS plus User Manual... -
Page 26: Cabling The Beetle /Ipos Plus
Cabling the BEETLE /iPOS plus All devices belonging to the modular BEETLE /iPOS plus that have a separate power cable must be connected to the same electric circuit. Connect the system as described below: Tilt the system to the back. - Page 27 Connect the power cable with the dedicated socket (3). Lay the cable through the cable duct. Proceed the same way with all the other cable connections (LAN, Mouse etc.). Then, close the cable duct (4). BEETLE /iPOS plus User Manual...
- Page 28 Reinsert the pedestal’s cover. Make sure that the strip corresponds to the notch at the pedestal (see arrow). The cover of the pedestal must engage and sit flushwith the pedestal. Push the cable cover backwards until it engages. BEETLE /iPOS plus User Manual...
- Page 29 Then you can switch on the system (see white arrow). Shortly press the Power button at the front side to start the system. Never connect data cables when the system is switched on. BEETLE /iPOS plus User Manual...
-
Page 30: Connector Panels System Unit
2 x USB- A (USB 2.0) 1 x USB powered 12V (2A max) 15-pin D-Sub-socket 2 x D-Sub (COM-interfaces), with power supply Mass storage (HDD/SSD) Make sure that all additional devices have an CE certificate. BEETLE /iPOS plus User Manual... -
Page 31: Jack Plug 3.5 Mm (Out)
10 MBit lights green 100 MBit right LED lights orange 1000 MBit Only connect shielded LAN cables (CAT5 or CAT5e for 1 GBit) as these offer a better protection in case of interferences in a network. BEETLE /iPOS plus User Manual... -
Page 32: Usb (Universal Serial Bus)- A
The power supply is 12V. This interface can also be used as a USB-A socket. You can connect a monitor to the BEETLE /iPOS plus via the 15-pin D-sub jack. An LCD screen can be connected alternatively if a TFT adapter is installed. -
Page 33: Disconnecting Cables
The lock is released. The metal of the plug is visible. To release a RJ12 plug push the latch under the plug to the top. You loosen the USB-A- connector by pushing the covering of the connector. BEETLE /iPOS plus User Manual... - Page 34 The P- USB connector is disengaged by pressing the spring that is marked by an arrow. Manually loosen the knurled screws of the COM or DVI interface connector. To release a RJ45 plug push down the latch (see arrow). BEETLE /iPOS plus User Manual...
-
Page 35: Storage Media
The most SSDs are flash memory based. Change Of the Hard Disk Drive First ensure that the device is switched off and that the power connector is disconnected. Tilt the system to the back. BEETLE /iPOS plus User Manual... - Page 36 Pull the cable cover forward out of the guide (see arrows). You find the HDD or SSD in the drive carrier (see arrow). Remove both screws (M3 x 7) that fix the drive carrier to the housing… … and pull out the drive carrier. BEETLE /iPOS plus User Manual...
- Page 37 Handle the hard disk with care while removing or mounting it. Do not touch exposed electronics. Install the new hard disk/SSD and fix it with the screws removed before. Mind the correct fitting position (see illustration). ① ② Data transfer ① Electrical connection ② BEETLE /iPOS plus User Manual...
- Page 38 Fix the carrier to the housing with the two screws. Push the cable cover into the guide until it engages. Now connect the device to the mains voltage and switch it on by pressing the power button at the front side. BEETLE /iPOS plus User Manual...
-
Page 39: Magnetic Swipe Card Reader (Option)
Swipe cards should never be allowed to come into contact with liquids. Swipe cards should not be bent or folded in any way. Swipe cards should not be allowed to come into close contact with a magnetic field. BEETLE /iPOS plus User Manual... -
Page 40: Cleaning Instructions
Connecting peripherals with the system switched on is not allowed. Unpack the parts and check whether the delivery matches the details of the delivery note. The delivery contains the Magnetic Swipe Card Reader (MSR) and two screws (M3 x 6). BEETLE /iPOS plus User Manual... - Page 41 You will find a flap at the rear side of your system at the position for the SwipeCard Reader. Remove this flap using a small screw driver. Connect the cable connectors and lay the cables into the openings provided. BEETLE /iPOS plus User Manual...
- Page 42 Place the Swipe Card Reader and tighten it with the supplied screws. Now connect the device to the mains voltage and switch it on by pressing the power button at the front side. BEETLE /iPOS plus User Manual...
-
Page 43: Fingerprint Reader (Option)
Handling is very comfortable. Just put your finger on the blue glowing window. The reader quickly and automatically will scan your fingerprint. For more information about function and handling contact Digital Persona www.digitalpersona.com BEETLE /iPOS plus User Manual... -
Page 44: Waiter Lock (Option)
USB interface. The readout of the data may be integrated easily in a software application. Magnetic Probe Programming the "Electronic Key Controller" for the Waiter's Lock is described in a separate "Programmers Guide". BEETLE /iPOS plus User Manual... -
Page 45: Customer Display (Option)
The voltage (12 V DC) is also supplied via this interface. The display module is installed at the rear side of the system. Display Module BEETLE /iPOS plus User Manual... -
Page 46: Cleaning Instructions
Connecting peripherals with the system switched on is not allowed. Unpack the components and verify that the scope of delivery is identical to the information on the delivery ticket. The delivery consists of the customer display and two screws (M3 x 6). BEETLE /iPOS plus User Manual... - Page 47 You will find a flap at the rear side of your system at the mounting position for the Customer Display. Remove this flap using a small screw driver. Connect the cable connectors and carefully lay the cables. BEETLE /iPOS plus User Manual...
- Page 48 Insert the display into the opening until it engages. Flap the display upwards and tighten it with the delivered screws. Now connect the BEETLE /iPOS plus to the mains voltage and switch it on by pressing the power button at the front side.
-
Page 49: Starting Up The System
Starting Up the System After installing the BEETLE /iPOS plus, switch on the system by using the Power button on the front panel. The system first performs an automatic self-test to test its basic functions. For example, you may see the following message (irrespective of processor type) on the monitor: WN „ID xx/xx Date“... - Page 50 If the operating system started up without an error, the application software is automatically booted, if necessary. A message is displayed as soon as the BEETLE /iPOS plus is ready for operation. For more detailed information see the manual for your application program.
-
Page 51: Appendix
- 25 °C up to + 60 °C RT: - 15 °C up to – 60 °C; Storage (1K2) PCT: - 20 °C up to - 60 °C Input Voltage 24 V Max. Power Consumption 7.5 A BEETLE /iPOS plus User Manual... -
Page 52: Interfaces (J2)
Cash drawer RJ45/ LAN 10/100 and 1000 Mbit/s AC Power Adapter Only use power supply units (PSU) released or approved by Wincor Nixdorf The PSU has to comply with the following minimal requirements and common standards: Rated input voltage 110VAC-240VAC Rated input current 2.5-1.25A... -
Page 53: Power Cable Selection
AC power adapter. I/O Port Name Volt (V) Max. Current (A) Max. Power (W) COM1* USB1 USB2 USB3 (powered 12V) 5/12V Output BEETLE /iPOS plus User Manual... -
Page 54: Total Current Consumption Of Interfaces
= 500mA, in total 2A Max. 5A @ 5V The total current consumption at 12V interfaces must not exceed 5A. Each COM* = 600 mA, in total 900mA Each USB = 1.5A, in total 2A Max. 5A @ 12V BEETLE /iPOS plus User Manual... -
Page 55: Wall-Mounting
Make sure that all cables are unplugged and the system is disconnected from the main power supply. Lay the BEETLE /iPOS plus screen-side-down on a scratch-free, soft work surface and remove the cable cover out of the guidance. Flap the pedestal downwards and loosen the two screws (M4 x 6), that hold the swivel joint cover (see arrows below). - Page 56 Remove the swivel joint cover. You see four screws (M4 x 8) tightening the pedestal. Loosen these four screws and remove the pedestal. Now you can install the BEETLE /iPOS plus to a VESA standard wall mount. Plug the cable connections and switch the system on by pressing the pow- er button at the front side.
-
Page 57: Uefi Bios Setup
The Setup program has been designed to make it as easy as possible. It is a menu-driven program, which means you can scroll through the various sub-menus and make your selections among the predetermined choices. BEETLE /iPOS plus User Manual... -
Page 58: Bios Menu Bar
Navigation Key(s) Description of Functions ← or → (keypad arrows) Select the menu item to the left or right. ↑ or ↓ (keypad arrows) Moves the highlight up or down between fields. BEETLE /iPOS plus User Manual... -
Page 59: General Help
Take some time to familiarize yourself with each of the legend keys and their corresponding functions. Practice navigating through the various menus and sub-menus. If you accidentally make unwanted changes to any of the fields, use the set default hot key <F9>. While moving around BEETLE /iPOS plus User Manual... -
Page 60: Main Menu
Advanced Menu ACPI Settings RTC Wake Settings CPU Configuration IDE Configuration USB Configuration Super I/O Configuration H/W Monitor PPM Configuration BIOS Info Menu BEETLE /iPOS plus User Manual... -
Page 61: Sub Menu Acpi Settings
This allows enabling or disabling power up the BEETLE on specific time while the BEETLE is in Soft-Off or Hibernate mode. If this option is enabled a wake time is programmable within next two lines. The first line is setting the hour in international format(0-23). -
Page 62: Wake-On Modes
2xxx MHz System Bus Speed 533 MHz Processor Core Dual Hyper-Threading Supported The lines list information about the installed CPU. You can use this screen to select options for the CPU Configuration. The content of the BEETLE /iPOS plus User Manual... -
Page 63: Sub Menu Ide Configuration
Select a configuration mode for SATA Controller. The options are [AHCI], [IDE] or [Hard Disk Pre-Delay] Sub Menu USB Configuration USB Configuration USB Devices : 1 Keyboard, 1 Mouse Legacy USB Support [Enabled] Device power-up delay [Auto] BEETLE /iPOS plus User Manual... -
Page 64: Sub Menu Super I/O Configuration
Serial Port 2 Configuration Serial Port 3 Configuration Serial Port 4 Configuration Serial Port 5 Configuration Serial Port 6 Configuration This setup screen shows the 6 onboard legacy serial ports. BEETLE /iPOS plus User Manual... -
Page 65: Sub Menu Super I/O Configuration Serial Port 1
Device Settings IO=3E8h; IRQ=5; Change Settings [IO=3E8h; IRQ=5;] Sub Menu Super I/O Configuration Serial Port 4 Configuration Serial Port 4 Configuration Serial Port 4 [Enabled] Device Settings IO=2E8h; IRQ=6; Change Settings [IO=2E8h; IRQ=6;] BEETLE /iPOS plus User Manual... -
Page 66: Sub Menu Super I/O Configuration Serial Port 5
: +1.184 V DRAM Voltage : +1.488 V 24 V : +24.460 V 12 V : +11.968 V : +5.026 V 3.3 V : +3.328 V CPU GPU voltage : +1.024 V CMOS Bat : +3.248 V BEETLE /iPOS plus User Manual... -
Page 67: Sub Menu Ppm Configuration
PRODUCT NAME: J2.0-NM10-AiO BIOS VERSION: 00/01 02/22/2013 Realtek LAN MAC 00 E0 4C 68 00 0E SYSTEM: Serial Number ----------------------------------------- Version ###------------------------------------ MAINBOARD: Serial Number ----------------------------------------- Version ----------------------------------------- POWER SUPPLY: Serial Number ----------------------------------------- Device Name ----------------------------------------- BEETLE /iPOS plus User Manual... -
Page 68: Chipset Menu
[128MB] Fixed Graphics Memory Size [128MB] This option enable the fixed video memory technology. This allow the system to share fixed video memory with the system memory. Configuration options: Choose shareable memory size [128MB] [256MB]. BEETLE /iPOS plus User Manual... -
Page 69: Sub Menu South Bridge
Configuration options: [Follow AC/Power] [Stay Off] [Last State]. Wake On USB [Enabled] This allows enabling or disabling power up the BEETLE when USB devices receives a call while the BEETLE is in Soft-Off or Hibernate mode. Configuration options: [Disabled] [Enabled]. -
Page 70: Boot Menu
8th Boot [UEFI] BBS Priorities Option ROM Messages 3 Number of seconds to wait for setup activation key. Bootup NumLock State [On] This option sets the NumLock during the system boot. Configuration options: [On] [Off] BEETLE /iPOS plus User Manual... - Page 71 These menu entries are used to specify the boot sequence from the available devices. Every entry (from #1 till #n) specifies a boot device that found during POST. BBS Priorities Specifies the priority sequence from available boot devices or even disables boot devices from BBS. BEETLE /iPOS plus User Manual...
-
Page 72: Security Menu
[Enabled]. This password allows full access to the UEFI BIOS Setup menu. To clear the password, highlight this field and press <Enter>. The same dialog box as above will appear. Press <Enter> and the password will be set to [Disabled]. BEETLE /iPOS plus User Manual... -
Page 73: Save & Exit Menu
NVRAM. The NVRAM is sustained by an onboard backup battery and stays on even when the BEETLE is turned off. Once this option is selected, a confirmation is asked. Select [Ok] to save changes and reset the system. -
Page 74: Launch Efi Shell From Filesystem Device
Power on. Reset type detection (soft/hard). 0x02 AP initialization before microcode loading 0x03 North Bridge initialization before microcode loading 0x04 South Bridge initialization before microcode loading 0x05 OEM initialization before microcode loading 0x06 Microcode loading BEETLE /iPOS plus User Manual... -
Page 75: Pei Phase
Pre-memory South Bridge initialization (South Bridge module specific) 0x1D – 0x2A OEM pre-memory initialization codes 0x2B Memory initialization. Serial Presence Detect (SPD) data reading 0x2C Memory initialization. Memory presence detection 0x2D Memory initialization. Programming memory timing information BEETLE /iPOS plus User Manual... - Page 76 Memory not installed 0x56 Invalid CPU type or Speed 0x57 CPU mismatch 0x58 CPU self test failed or possible CPU cache error 0x59 CPU micro-code is not found or micro-code update is failed 0x5A Internal CPU error BEETLE /iPOS plus User Manual...
-
Page 77: Pei Beep Codes
Memory not Installed Memory was installed twice (InstallPeiMemory routine in PEI Core called twice) Recovery started DXEIPL was not found DXE Core Firmware Volume was not found Recovery failed S3 Resume failed Reset PPI is not available BEETLE /iPOS plus User Manual... -
Page 78: Dxe Phase
PCI Bus initialization is started 0x93 PCI Bus Hot Plug Controller Initialization 0x94 PCI Bus Enumeration 0x95 PCI Bus Request Resources 0x96 PCI Bus Assign Resources 0x97 Console Output devices connect 0x98 Console input devices connect BEETLE /iPOS plus User Manual... - Page 79 Some of the Architectural Protocols are not available 0xD4 PCI resource allocation error. Out of Resources 0xD5 No Space for Legacy Option ROM 0xD6 No Console Output Devices are found 0xD7 No Console Input Devices are found 0xD8 Invalid password BEETLE /iPOS plus User Manual...
-
Page 80: Dxe Beep Codes
# of Beeps Description Invalid password Some of the Architectural Protocols are not available No Console Output Devices are found Flash update is failed Reset protocol is not available Platform PCI resource requirements cannot be met BEETLE /iPOS plus User Manual... -
Page 81: Abbreviations
Light Emitting Diode Protective Earth Neutral Conductor Random Access Memory Solid State Disk (flash medium) TN-S Terre Neutre- Separé Underwriters Laboratory (standards) Universal Serial Bus Video Graphics Adapter VESA Video Electronics Standards Association Wincor Nixdorf International GmbH BEETLE /iPOS plus User Manual... - Page 82 Wincor Nixdorf International GmbH D-33094 Paderborn Order No.: 01750245230A...
Need help?
Do you have a question about the BEETLE and is the answer not in the manual?
Questions and answers
Buenos días: Tenemos un equipo BEETLE/iPOS, nos gustaría utilizarlo para un comercio de venta de ropa interior que vamos a abrir en breve. Seria posible?
Yes, the Wincor Nixdorf BEETLE/iPOS can be used for a clothing retail business. It is designed for retail environments, supports mobile and fixed POS functions, handles tasks like stock taking and inventory ordering, and is built for larger retailers. It allows online ordering, payment processing, and customer information access, making it suitable for clothing retail operations.
This answer is automatically generated