Table of Contents
Advertisement
Before starting to build, take an inventory of this kit to make sure it is complete, and inspect the parts to make sure they
are of acceptable quality. If any parts are missing or are not of acceptable quality, or if you need assistance with assembly,
contact Product Support. When reporting defective or missing parts, use the part names exactly as they are written in
the Kit Contents list.
1
2
Wood parts:
Plywood ignition kill switch mount set
Plywood pushrod guide tube mounts (2)
10x45 mm wing dowels (2)
6x30 mm antirotation dowel
Cowl mounting blocks for gas engines (2)
Wing bolt plates (2)
Nuts, bolts, washers:
1/4-20x2" [50 mm] nylon wing bolts (2)
8-32x1-1/4" [32 mm] socket head cap screws
(SHCS) (engine mount) (4)
8-32 x 1" [25 mm] SHCS (engine) (4)
#8 flat washers (engine mount) (4)
#8 lock washers (4-engine, 4-engine mount) (8)
8-32 blind nuts (engine mount) (4)
4-40 x 3/4" [19 mm] Phillips screws (control
horns on elevators, rudder) (12)
#4x5/8" [16 mm] Phillips screws (16-main
landing gear straps, 6-cowl, 8-aileron control
horns) (30)
#4 flat washers (cowl) (6)
#4 lock washers (cowl) (6)
4-40 nuts (lock nuts for clevises on pushrods) (5)
2-56 x 3/8" [9.5 mm] Phillips screws (wheel pant
mounting) (8)
#2 x 3/8" [3/8 mm] Phillips screws (tail gear
mounting) (2)
#2 flat washers (wheel pant mount) (8)
2-56 blind nuts (wheel pant mount) (8)
2-56 ball link ball (gas engine throttle) (1)
2-56 lock nut (gas engine throttle) (1)
Brass screw-lock connector (throttle servo) (1)
KIT INSPECTION
Great Planes Product Support:
3002 N Apollo Drive, Suite 1
Champaign, IL 61822
Telephone: (217) 398-8970, ext. 5, Fax: (217) 398-7721
E-mail: airsupport@greatplanes.com
KIT CONTENTS
3
8
4
11
4
12
13
Kit Contents (Not Photographed)
4-40x1/8" [3.2 mm] SHCS for screw-lock (1)
Nylon retainer for screw-lock (1)
4-40x12" [300 mm] pushrods (2-elevators, 1-
rudder, 2-ailerons) (5)
4-40 metal clevises (2-elevators, 1-rudder, 2-
ailerons) (5)
Large solder clevises (2-elevators, 1-rudder,
2-ailerons) (5)
3/32" [2.4 mm] wheel collar (tail wheel) (1)
4-40 set screw for wheel collar (1)
1" [25 mm] tail wheel (1)
2-56 x 1" [25 mm] threaded rod (for gas throttle
pushrod) (1)
2-56 x 36" [910 mm] pushrod (glow throttle
pushrod) (1)
1/4-20 blind nuts (in fuselage) (2)
Metric fasteners for mounting
Fuji-Imvac 32 engine:
(4) 5x60 mm SHCS
(4) 5 mm lock washers
(4) 5 mm blind nuts
(4) 5 mm wheel collars
(4) 3x5 mm Phillips screw
5x12 mm flat washers (4-engine mounting,
8-wheel spacers) (12)
Hardware:
1.20–1.80 R & L engine mount halves
Aluminum Fuji-Imvac 32 engine spacers (4)
Hump straps (4-wheel pant mount, 2-spares) (6)
6
10
9
7
5
14
24" [610 mm] white, plastic pushrod (for gas
24" [610 mm] gray throttle pushrod guide tube
Giant control horns (5)
Giant control horn mounting plates (1)
Flat landing gear straps (main landing gear
Nylon ball link (for gas throttle pushrod) (1)
Nylon clevis (for glow throttle pushrod) (1)
Clevis retainers (11)
3/8" [9.5 mm] heatshrink tubing (for servo wires) (1)
CA hinge strips (2)
Velcro
Inner, outer fueling line collar (1 glow, 1 gas) (2)
Fuel line plug (2)
Decal sheet
Tail gear assembly:
Tail gear wire
Collar with set screw
Nylon tail gear bearing
Collar w/3mm set screw
Aluminum bracket
Steering post (in rudder)
Spinner assembly:
3-1/4" [83 mm] aluminum spinner
3/8-24 jam nut
Collored spacer ring
5 x 35 mm spinner bolt
5 x 55 mm spinner bolt
5 mm nut
6
Kit Contents (Photographed)
1 Fuselage
2 Cowl
3 Canopy
4 Wing halves w/ailerons (R&L)
5 Horizontal stabilizer w/elevators
6 Vertical stabilizer (fin) w/rudder
7 (2) wheel pants
8 (2) 3-1/2" [87 mm] main wheels
9 (2) Right and left main landing
gear wires
10 Tail gear wire
11 Aluminum wing joiner tube
12 Battery tray
13 Servo tray
14 Fuel tank w/hardware
engine) (1)
(for gas engine) (1)
mount) (8)
®
strips (2)
Hide quick links:
Advertisement
Table of Contents
