Parts List - KNOVA KN M-2500W Manuals

TROUBLESHOOTING GUIDE
TROUBLESHOOTING GUIDE - SAW OPERATION
PROBLEM PROBLEM CAUSES
1. Misalignment.
Blade hits table.
Angle of cut not
1. Miter table unlocked.
accurate. Can not
adjust miter.
2. Sawdust under table.
Cutting arm
1. Loose pivot points.
wobbles.
1. Pivot bolt too tight.
Cutting arm will
not fully raise, or
2. Pivot spring not replaced properly after
blade guard won't
fully close.
3. Sawdust build-up.
1. Improper operation.
Blade binds, jams,
burns wood.
2. Dull or warped blade.
3. Improper blade size.
4 Wood is moving during cut.
1. Saw blade not round / damaged / loose.
Saw vibrates or
shakes.
2. Arbor bolt loose.

PARTS LIST

10 in. COMPOUND MITER SAW
WARNING
When servicing use only the following replacement parts. Use of any other parts many create a HAZARD or cause product
damage. Any attempt to repair or replace electrical parts on this Miter Saw may create a HAZARD unless repair is done by a
qualified service technician. Repair service is available at your nearest Service Center.
PARTS LIST FOR SAW SCHEMATIC
Key No. Description
0824
PIVOT SHAFT
0828 ROTATION SLIDE PLATE
0831 SHAFT SLEEVE
081A PLASTIC SLEEVE
083S TRIGGER
083Z CORD CLAMP
0B5N COMPRESSION SPRING
0CES COMPRESSION SPRING
0CPD CENTER BOLT
0CV5 DUST BAG ASS'Y
0D7X SHAFT
0D87 TORSION SPRING
0D99 SHIM
0D9B
ANCHOR BLOCK
0DHT SPRING GUARD
0DVJ BLADE WRENCH
service.
SUGGESTED CORRECTIVE ACTION
1. See ADJUSTMENT - Cutting Arm Travel section.
1. See OPERATION - Miter Angle Adjustment section.
2. Vacuum or blow out dust. WEAR EYE
PROTECTION.
1. See ADJUSTMENT - Cutting Arm Travel section.
1. Loosen pivot bolt lock nut (see adjustment section).
2. Knova Service Center.
3. Clean and lubricate moving parts.
1. See BASIC SAW OPERATION section.
2. Replace or sharpen blade.
3. Replace with 10 in. diameter blade.
4. Use hold down clamp to secure workpiece to table.
1. Replace blade.
2. Tighten arbor bolt.
Qty Key No.
Size
1
0J4E FLAT WASHER
1 0J4F FLAT WASHER
1 0J4J FLAT WASHER
1 0J7R
FLAT WASHER
1 0JB0 WAVE WASHER
1 0JET E-RING
1 0JMM O-RING
1 0JPE HEX. HD. BOLT
1 0JPG HEX. HD. BOLT
1 0JUK HEX. SOC. HD. CAP BOLT
1 0JZF HEX. SOC. SET SCREW
1 0JZN ARBOR BOLT
1 0K0W HEX. HD. SCREW AND WASHE
1 0K2N HEX SOC. HD. CAP SCREW
1 0K5C CR. RE. COUNT HD. SCREW
1 0K75 CR. RE. TRUSS HD. SCREW
18
Description
Qty
Size
ø6*13-1 1
ø8*16-2.5 1
ø10*20-2 1
1/2*1-3/64 1
WW-8 1
1
1
M6*1.0-20 2
M6*1.0-30 1
M6*1.0-16 1
M6*1.0-10 3
M8*1.25-20 1
M6*1.0-25 2
M8*1.25-25 2
M6*1.0-16 1
M6*1.0-12 2