Related Manuals for Notifier NFS-3030/E
Summary of Contents for Notifier NFS-3030/E
-
Page 1: Installation Manual
Fire Alarm Control Panel NFS-3030/E Installation Manual Document 51330 10/28/2003 Rev: P/N 51330:C ECN 03-419... - Page 2 Fire Alarm System Limitations While a fire alarm system may lower insurance rates, it is not a substitute for fire insurance! An automatic fire alarm system—typically made up of Heat detectors do not sense particles of combustion and smoke detectors, heat detectors, manual pull stations, audible alarm only when heat on their sensors increases at a predeter- warning devices, and a fire alarm control panel with remote mined rate or reaches a predetermined level.
-
Page 3: Installation Precautions
Acclimate Plus™, AWACS™, HARSH™, NOTI•FIRE•NET™, ONYX™, and VeriFire™ are trademarks, and FlashScan®, UniNet®, and VIEW® are registered trademarks of NOTIFIER. NION™ is a trademark of NIS. NIS™ and Notifier Integrated Systems™ are trademarks and NOTIFIER® is a registered trademark of Fire•Lite Alarms, Inc. Echelon® is a registered trademark and LonWorks™ is a trademark of Echelon Corporation. ARCNET® is a registered trademark of Datapoint Corporation. - Page 4 Documentation Feedback Your feedback helps us keep our documentation up-to-date and accurate. If you have any comments or suggestions about our online Help or printed manual, you can email Please include the following information: • Product name and version number (if applicable) •...
-
Page 5: Table Of Contents
Table of Contents Table of Contents Section 1 About This Manual ......................7 1.1 Standards and Other Documents ...................7 1.2 Supplemental Documentation ....................8 1.3 Cautions and Warnings ......................9 Section 2 System Overview ......................10 2.1 System Description ......................10 2.1.1 Standard Features .....................10 2.1.2 Options ........................10 2.1.3 System Limitations ....................10 2.2 System Components ......................11... - Page 6 Table of Contents 4.2 Devices Requiring External Power Supervision ..............47 4.3 NFPA 72 Central or Remote Station Fire Alarm System (Protected Premises Unit) ..48 4.4 NFPA 72 Proprietary Fire Alarm Systems ................49 4.5 Fire/Security Applications ....................50 4.5.1 General Operation ....................50 4.5.2 General Security Requirements ................50 4.5.3 Installing a Security Tamper Switch ................51 4.5.4 Receiving Unit ......................51...
-
Page 7: Section 1 About This Manual
NFPA 17A Wet Chemical Extinguishing Systems NFPA 72-1999 Central Station Fire Alarm Systems (Automatic, Manual and Waterflow) Protected Premises Unit (requires Notifier UDACT). NFPA 72-1999 Local (Automatic, Manual, Waterflow and Sprinkler Supervisory) Fire Alarm Systems. NFPA 72-1999 Auxiliary (Automatic, Manual and Waterflow) Fire Alarm Systems (requires TM-4). -
Page 8: Supplemental Documentation
15378 Fire Alarm Control Panel (FACP) and Main Power Supply Installation Document Number NFS-3030/E FACP Installation, Operations, and Programming Manuals 51330, 51345, 51344 (Note: Where used in this manual, NFS-3030 refers to both NFS-3030 and NFS-3030E) Voice Alarm System Manual... -
Page 9: Cautions And Warnings
Cautions and Warnings Section 1 About This Manual Table 1 Related Documentation (Sheet 2 of 2) UZC-256 Universal Zone Coder Manual 15216 UZC-256 Programming Manual 15976 XP Transponder Manual 15888 XP10-M Ten Input Monitor Module Installation Document I56-1803 XP5 Series Manual 50786 XP6-C Supervised Control Module Installation Document I56-1805... -
Page 10: Section 2 System Overview
Signaling Line Circuit (SLC) loops of new devices • Network operation • Easy connection to VeriFire Tools • Uses Notifier’s VIEW® early warning fire programming utility detection and the FlashScan® or CLIP • The basic system power supply is addressable,... -
Page 11: System Components
Section 2 System Overview 2.2 System Components Central Processing Unit (CPU). The central processing unit for an NFS-3030/E system can be ordered with a keypad/display (P/N CPU-CPU-3030D) or without a keypad/display (P/N CPU- 3030ND). CPU-3030D serves as “primary display” version for ULC applications. CPU-3030ND is intended for use in network applications;... - Page 12 Section 2 System Overview Product Diagram Figure 1 CPU Connections Note: Relay circuits are power-limited only if TB7 ACS (power-limited, supervised) connected to a power-limited signal source. Relays are rated for 2A@30Vdc resistive. TB9 RDP devices such as LCD-160 TB1 Security Relay TB2 Supervisory Relay TB9 TOUT+/- : Future Use TB5, left side.
-
Page 13: Main Power Supply
Product Diagram Section 2 System Overview The keyboard/display Figure 2 CPU-3030D (Shown with Two Annunciators) assembly is shown in Figure 2. As shown in Figure 3, LEDs on the keyboard/display are repeated on the printed circuit board. This enables operation and trouble-shooting when the panel is used without the display assembly. -
Page 14: System Cabinets
Section 2 System Overview System Cabinets 2.4 System Cabinets The CPU and modules are installed in a CAB-4 series backbox. There are four different sizes available, holding from one to four rows of equipment plus batteries (up to two 25AH batteries). Backboxes are ordered separately from doors. -
Page 15: Compatible Equipment
Section 2 System Overview 2.5 Compatible Equipment Compatible Notifier and System Sensor equipment that connects directly to the CPU is listed below. These are the most common devices at time of publishing; the most complete list of compatible intelligent SLC loop devices is provided in the SLC Wiring Manual; for conventional non-addressable equipment see the Device Compatibility Document. -
Page 16: System Sensor Compatible Equipment
Section 2 System Overview Compatible Equipment PRN-4 80-Column Printer STS-1 Security Tamper Switch (Not ULC-listed) PRN-5 80-Column Printer TM-4 Transmitter Module PRN-6 80-Column Printer UDACT Universal Digital Alarm Communicator R-120 120 Ohm End-of-Line Resistor Transmitter R-2.2K 2.2K End-of-Line Resistor UZC-256 Universal Zone Coder R-27K 27K End-of-Line Resistor VCE-4 Voice Control Expander R-470 470 End-of-Line Resistor... -
Page 17: Section 3 Installation
Preparing for Installation Section 3 Installation Section 3 Installation 3.1 Preparing for Installation Choose a location for the fire alarm system that is clean, dry, and vibration-free with moderate temperature. The area should be readily accessible with sufficient room to easily install and maintain it. There should be sufficient space for cabinet door(s) to open completely. - Page 18 Section 3 Installation Installation Checklist Table 2 Installation Checklist (Sheet 2 of 2) Task Refer to: Printer or other output device(s) Section 3.18 “Installing Printers” Network devices Noti•Fire•Net Version 4.0 & Higher Manual, and/or Installation document for specific device(s) Wire the Signaling Line Circuits. Section 3.19 “Wiring a Signaling Line Circuit (SLC)”...
-
Page 19: Mounting A Cabinet
Mounting a Cabinet Section 3 Installation 3.3 Mounting a Cabinet This section provides instructions for mounting the CAB-4 Series backbox to a wall. Follow these guidelines when mounting the backbox: • Locate the backbox so that the top edge is 66 inches (1.6764 m) above the surface of the finished floor. -
Page 20: Laying Out Equipment In Cabinet And Chassis
Section 3 Installation Laying Out Equipment in Cabinet and Chassis 3.4 Laying Out Equipment in Cabinet and Chassis The NFS-3030 allows for flexible system Figure 5 Chassis CHS-M3 design. Follow these guidelines when Four positions deciding where to locate equipment in the on chassis backbox. -
Page 21: Attaching The Cpu & Chassis
Attaching the CPU & Chassis Section 3 Installation separation of power-limited and non-power-limited wiring; for example, having all non-power-limited circuits grouped in one area of the cabinet (see Section 3.16 “UL Power-limited Wiring Requirements” and your power supply manual). 3.5 Attaching the CPU & Chassis Mount CPU into positions 1 and 2 of CHS-M3 as follows;... -
Page 22: Memory-Backup Battery
CAUTION: The battery used in this device may present a risk of fire or chemical burn if mistreated. Do not recharge, disassemble, heat above 212°F (100°C), or incinerate. Replace battery with Notifier P/N LITHBATT-3V only. Use of another battery may present a risk of fire or explosion. -
Page 23: Attaching Panel Circuit Modules
Attaching Panel Circuit Modules Section 3 Installation Note: Install four 1 inch (25.4 mm) stand-offs onto the chassis as shown in Figure 8. Place the first option board over the stand-offs so that holes line up. If no more option boards will be mounted in that position, securely fasten all stand-offs with screws (provided with module). -
Page 24: Mount Expander Boards
Attaching Panel Circuit Modules • Type your point-programming information onto the slide-in labels provided with your panel circuit module or create custom labels with LabelEase (available from Notifier); insert these labels into the slots at the top of the module. -
Page 25: Installing A Multi-Layer Module Into The Chassis
Attaching Panel Circuit Modules Section 3 Installation 3.7.3 Installing a Multi-layer Module into the Chassis Follow the instructions illustrated in Figure 11 to install a panel circuit module or a pair of loop control/ expander modules into into CHS-4N or CHS-M3. NOTE: Loop control/expander modules can also mount in CHS-4;... -
Page 26: Connecting Expander Row Ribbon Cables
Section 3 Installation Attaching Panel Circuit Modules 3.7.4 Connecting Expander Row Ribbon Cables Expander Row Ribbon Cables connect panel circuit modules such as Indicating Circuit Modules (ICM-4RK) or Control Relay Modules (CRM-4RK) to the CPU. Shown below is a typical wiring setup connecting the control panel to three rows of panel circuit modules each below the CPU in a CAB-4 Series backbox. -
Page 27: Initiating Device Circuits With Izm-8Rk/Ize-A
Initiating Device Circuits with IZM-8RK/IZE-A Section 3 Installation 3.8 Initiating Device Circuits with IZM-8RK/IZE-A 3.8.1 Style B Field Wiring IZM-8RK Initiating Zone Module for up to eight Style B Initiating Device Circuits. Figure 13 NFPA Style B Field Wiring of the IZM-8RK Initiating Zone Module Typical NFPA Style B Initiating Device Circuit 4.7K, 1/2 watt ELR (71252) UL/ULC-listed two-wire smoke detector... -
Page 28: Style D Field Wiring
Section 3 Installation Initiating Device Circuits with IZM-8RK/IZE-A 3.8.2 Style D Field Wiring Figure 14 Style D Field Wiring of IZM-8RK Initiating Zone Module with IZE-A Expander Typical NFPA Style D Initiating Device Circuit UL/ULC-listed two-wire smoke detector. Manual Pull Station Heat Detector Jumper all unused circuits... -
Page 29: Nacs With Icm-4Rk⁄Ice-4
NACs with ICM-4RK⁄ICE-4 Section 3 Installation 3.9 NACs with ICM-4RK⁄ICE-4 Optional ICE-4 Indicating Circuit Expander. b+ a+ a- b- b+ a+ a- b- Positions E, F, G, and H are active only with this board installed. b+ a+ a- b- b+ a+ a- b- Note that CRE-4 expander may also be installed on the ICM-4RK. -
Page 30: Power Supply Connections
Section 3 Installation NACs with ICM-4RK⁄ICE-4 Figure 16 Location of D35 on ICM-4RK Circuit Board Cut D35 on the circuit board to produce California code. Power Supply Connections Figure 17 illustrates typical connections from the main power supply. Figure 18 shows location of those connections on the bottom of the ICM-4RK and the ICE-4 modules. -
Page 31: Form-C Relays On The Cpu
Form-C Relays on the CPU Section 3 Installation 3.10 Form-C Relays on the CPU The panel provides a set of Form-C relays. These are rated for 2 A at 30 VDC (resistive): • Alarm - TB4 • Trouble - TB3 •... -
Page 32: Form-C Relays With Crm-4Rk/Cre-4
Section 3 Installation Form-C Relays on the CPU 3.11 Form-C Relays with CRM-4RK/CRE-4 Figure 20 Field-Wiring a CRM-4RK or CRE-4 Module * Optional CRE-4 Control Relay Expander. Positions E, F, G and H are active only with this board installed. These Form-C gold-plated, silver alloy relay contacts are for medium duty switching or Pilot Duty. -
Page 33: Form-C Relays With Auxiliary Relay Module (Arm-4)
Form-C Relays on the CPU Section 3 Installation 3.12 Form-C Relays with Auxiliary Relay Module (ARM-4) Overview If a CRM-4RK/CRE-4 is to be incorporated into the control panel and an ARM-4 is being driven by it, the ARM-4 should be installed at the same time. Keep the following in mind: •... -
Page 34: Field Wiring An Auxiliary Relay Module
Section 3 Installation Form-C Relays on the CPU Field Wiring an Auxiliary Relay Module The figure above shows terminal assignments for ARM-4 module control relays K1-K4, which control non-power-limited circuits. Power-limited and non-power-limited circuit wiring must remain separated by at least 0.25 inch (6.35 mm) within the cabinet and exit the cabinet though different knockouts, conduits, or both. -
Page 35: Notification Appliance Circuit Current Limitations
Form-C Relays on the CPU Section 3 Installation 3.13 Notification Appliance Circuit Current Limitations The total current available from any group of Indication Appliance Circuits cannot exceed 3.0 amps. Figure 22 illustrates some of the typical power J5 J6 supply/ Notification Appliance Circuit configurations. (ICM-4RK) J5 J6 Note: The term “total”... -
Page 36: Connecting Specific Option Boards
Section 3 Installation Form-C Relays on the CPU 3.14 Connecting Specific Option Boards 3.14.1 Network Control Module If networking two or more CPU units, each one requires a Network Control Module; a wire version and a fiber version are available. The NCM-W/F can be installed in any panel circuit module position (see Section 3.7 “Attaching Panel Circuit Modules”);... -
Page 37: Lcm-320 & Lem-320 Connecting Diagram
Form-C Relays on the CPU Section 3 Installation Figure 23 LCM-320 & LEM-320 Diagram TB1 SLC Loop TB1 SLC Loop Connection B+ A+ B- A- B+ A+ B- A- Connection J3 Data Out to next LCM-320 J1 Data In from control panel or from previous LCM-320 Ground Fault LEDs: D32 LEM-320 Ground Fault... - Page 38 Section 3 Installation Form-C Relays on the CPU Figure 25 Inserting LCM-320/LEM-320 into CHS-4L Angle tab on LCM-320 Use a slimline screwdriver (3/32") into slot on CHS-4L to fasten down LEM-320 through the hole in the LCM-320 board. Figure 26 SLC Loop Connections on LCM-320 and LEM-320 B+ A+ B- B+ A+ B- LCM-320PCA...
-
Page 39: Connecting Power Sources And Outputs
Connecting Power Sources and Outputs Section 3 Installation 3.15 Connecting Power Sources and Outputs WARNING: Remove all power sources to equipment while connecting electrical components. Leave the external, main power breaker OFF until installation of the entire system is complete. WARNING: Several sources of power can be connected to the control panel. -
Page 40: Checking Ac Power
Section 3 Installation Connecting Power Sources and Outputs Figure 28 DC Power Connections: Main Power Supply Cable 75591 AMPS-24 CPU-3030 Main Power Supply 3.15.1 Checking AC Power Table 4 contains a checklist for checking the system with AC power applied to the main power supply: CAUTION: While checking AC power, make sure batteries are not connected. -
Page 41: Ul Power-Limited Wiring Requirements
ULC Remote Connection Feature Section 3 Installation 3.16 UL Power-limited Wiring Requirements Power-limited and non-power-limited circuit wiring must remain separated in the cabinet. All power- limited circuit wiring must remain at least 0.25 inches (6.35 mm) from any non-power-limited circuit wiring. -
Page 42: Installing Printers
Section 3 Installation Installing Printers key-removed is the closed position; it should be located inside the same backbox as the UDACT, as close to the UDACT as possible. Note: During testing when the key switch is turned, the panel will report a communication failure for the UDACT’s address. - Page 43 Installing Printers Section 3 Installation Figure 31 Printer Connections Keltron Printer VS4095/5 DB-25 connector on DB-25 connector on power connections* PRN-5 Keltron Printer VS4095/5* DC IN + DC IN - Note: Outputs are power-limited but are not supervised. TB6 of AMPS-24/E TB5 on Control Panel TB5 on Control Panel *Note: VS4095/5 is not ULC-listed.
-
Page 44: Configuring The Printer
Section 3 Installation Installing Printers 3.18.2 Configuring the Printer Refer to the documentation supplied with your printer for instructions on configuring your printer. PRN-5 Printer Settings Keltron Printer VS4095/5 Settings Set the printer options (under the menu area) The printer communicates using the following according to the settings listed in Table 5. -
Page 45: Wiring A Signaling Line Circuit (Slc)
Wiring a Signaling Line Circuit (SLC) Section 3 Installation 3.19 Wiring a Signaling Line Circuit (SLC) Overview Communication between the CPU and intelligent and addressable initiating, monitor, and control devices takes place through a Signaling Line Circuit (SLC). You can wire an SLC to meet the requirements of NFPA Style 4, Style 6, or Style 7 circuits. -
Page 46: Connecting A Pc For Programming
Section 3 Installation Connecting a PC for Programming Figure 32 SLC Loop Connections and Wiring B+ A+ B- A- B+ A+ B- A- SLC Loop Connections SLC Loop #2 Connections on Loop Control Modules on Loop Expander Module Channel Channel Channel B (output loop) Channel A (loop return) T-Tapping is not allowed... -
Page 47: Section 4 Applications
Overview Section 4 Applications Section 4 Applications 4.1 Overview A listing of chapters and topics covered in this section: Chapter Covers the following topics Section 4.3 “NFPA 72 How to install a UDACT with the CPU for use as a Central or Remote Station NFPA Central or Remote Station Fire Alarm System Fire Alarm System... -
Page 48: Nfpa 72 Central Or Remote Station Fire Alarm System (Protected Premises Unit)
Section 4 Applications NFPA 72 Central or Remote Station Fire Alarm System (Protected Premises Unit) 4.3 NFPA 72 Central or Remote Station Fire Alarm System (Protected Premises Unit) The figure below shows typical wiring diagram for a NFPA 72-1999 Central Station Fire Alarm System (Protected Premises Unit) or a Remote Station Fire Alarm System (Protected Premises Unit) using the Universal Digital Alarm Communicator/Transmitter (UDACT) and NFS-3030. -
Page 49: Nfpa 72 Proprietary Fire Alarm Systems
NFPA 72 Proprietary Fire Alarm Systems Section 4 Applications 4.4 NFPA 72 Proprietary Fire Alarm Systems When connected and configured as a protected premises unit with monitor and relay modules, the NFS- 3030 will automatically transmit General Alarm, General Trouble, General Supervisory, and Security signals to a listed compatible Protected Premises Receiving Unit. -
Page 50: Fire/Security Applications
Section 4 Applications Fire/Security Applications 4.5 Fire/Security Applications Note: The NFS-3030 is not approved for use in security applications in Canada. 4.5.1 General Operation The NFS-3030 can be used as a combination Fire/Security system when installed and operated according to the instructions in this section. For security applications, program one or more monitor module (listed for security applications) with , or Type Codes, and wire as shown in Figure 37. -
Page 51: Installing A Security Tamper Switch
Fire/Security Applications Section 4 Applications 4.5.3 Installing a Security Tamper Switch Follow the instructions below to wire the cabinet with a Security Tamper Switch kit model STS-1. Install the STS-1 Tamper Switch onto the side of the backbox opposite the door hinge, pushing the switch through the opening until it snaps into place. -
Page 52: Wiring For Proprietary Security Alarm Applications
Section 4 Applications Fire/Security Applications 4.5.6 Wiring for Proprietary Security Alarm Applications Typical wiring for proprietary security alarm applications with the FMM-1 module. Note the following: • The module is programmed with one of five type codes (see Section 4.5.2 “General Security Requirements”). -
Page 53: Connecting An Rks-S Remote Key Switch
Fire/Security Applications Section 4 Applications 4.5.7 Connecting an RKS-S Remote Key Switch The RKS-S Remote Key Switch arms and disarms the system. It can be mounted in a UL listed single- gang electrical box. Both the monitor module and RKS-S must be mounted within the protected area. Figure 38 and Figure 39, respectively, depict the connection of the FMM-101 or FMM-1 module to the RKS-S. -
Page 54: Single Tenant Security System With Entry/Exit Delay
Section 4 Applications Fire/Security Applications Figure 39 Connecting the FMM-1Module to the RKS-S Signaling Line Circuit Signaling Line Circuit TENS ONES LOOP ADDRESS Wire an R- 47K End-of- FMM-1 Line Resistor into the circuit RKS-S rear 4.5.8 Single Tenant Security System with Entry/Exit Delay The following system requirements are illustrated in Figure 40. -
Page 55: Programming Notes For Figure
Fire/Security Applications Section 4 Applications Figure 40 Single Tenant Security System with Entry/Exit Delay TENANT A Motion Detector Contact Switch Contact Switch with MM Module AREA 1 (Perimeter RKS-S Remote Key Switch with MM Module and interior) MM Security Access Monitor Remote Annunciator Group Interface * * Group Interface must be... -
Page 56: Security Annunciation
Section 4 Applications Fire/Security Applications 3. Programming Group Interfaces MM CM Group Interface for Trouble when Group Interface for Security Alarm system is armed while access A. CM programming point(s) active Address: LXXMYYY (arbitrary) A. CM programming Type ID: RELAY Address: LXXMYYY (arbitrary) Zone Map:... -
Page 57: Releasing Applications
Fire/Security Applications Section 4 Applications 4.6 Releasing Applications Overview This control panel can be used for non-hazardous agent release or preaction/deluge control applications via the SLC loop. In a properly configured system with compatible, listed actuating and initiating devices, this control panel complies with the following NFPA standards for installation in accordance with the acceptable standard: Table 7 NFPA Standards for Releasing Applications Standard... -
Page 58: Connecting A Releasing Device To A Fcm-1 Module
Section 4 Applications Fire/Security Applications 4.7 Connecting a Releasing Device to a FCM-1 Module Typical Connections. Figure 42 shows typical connections for wiring a releasing device to a module. For ULC applications, REL-47K is required; see chart in Circuit Requirements below. Figure 42 Typical Connection of a 24 VDC Releasing Device to the FCM-1 Control Module SLC from FACP... - Page 59 Fire/Security Applications Section 4 Applications Figure 43 Typical Connections for an NBG-12LRA Agent Release-Abort Station SLC loop to FACP, LCM-320, or LEM-320 NBG-12LRA Manual Abort Yellow Black FMM-101 See Document 51369 for installation details. Violet Manual Release Yellow Black FMM-101 Violet Non-resettable +24 VDC Normal...
-
Page 60: Section 5 Testing The System
Section 5 Testing the System Acceptance Test Section 5 Testing the System 5.1 Acceptance Test When finished with the original installation and all modifications, conduct a complete operational test on the entire installation to verify compliance with applicable NFPA standards. Testing should be conducted by a factory-trained fire alarm technician in the presence of a representative of the Authority Having Jurisdiction and the owner's representative. -
Page 61: Battery Checks And Maintenance
Battery Checks and Maintenance Section 5 Testing the System Remove AC power, activate an Initiating Device Circuit through an alarm initiating device or an addressable initiating device on the SLC, and check that programmed active notification appliances sound, and alarm indicators illuminate. Measure the battery voltage with notification appliances active. -
Page 62: Appendix A Electrical Specifications
Appendix A Electrical Specifications Operating Power Appendix A Electrical Specifications A.1 Operating Power DC Power The control panel requires connection to a +24 VDC regulated power supply, UL/ULC-listed for fire protective service, that can supply 0.1 amps continuous for CPU-3030ND (0.3 amps for CPU-3030D). For complete battery/current draw calculations, refer to the main power supply manual;... -
Page 63: Wire Requirements
Wire Requirements Appendix A Electrical Specifications A.4 Wire Requirements Each type of circuit within the Fire Alarm Control System requires use of a specific wire type to ensure proper circuit operation. The wire gauge of a particular circuit depends on the length of that circuit and the current traveling through it. -
Page 64: Appendix B Canadian Applications
Appendix B Canadian Applications Standalone Application Appendix B Canadian Applications B.1 Standalone Application CPU-3030D, with its integral keypad/display, meets Canadian requirements for standalone applications. Its 640-character, multi-line display complies with ULC requirements for primary displays. B.2 Local Network Application To meet ULC requirements, the network’s Manual Controls may only be operated from one location at any given time. - Page 65 Index Index AC power, see your power supply manual 40 FCM-1 58 acceptance test 60 fire/security applications 50 ACM-8R 41 FMM-1 52 ADP-4B 14 Form-C relays see relays 31 Agent Release-Abort Station 58 alarm relays see relays 31 ARM-4 ICM-4RK installation steps 33–34 connections 29, 30 stand-off and terminal locations 33...
- Page 66 Index ribbon cables 26 UL requirements 41 see also ICM-4RK, ICE-4, CRM-4RK, CRE-4, and ULC remote connection feature 41 Voice Alarm System Manual 23 upload/download software 46 PC connection 46 periodic testing 60 power 39 VeriFire™ Tools 46 AC power checklist 40 AC power connections also see your power supply manual 40 wiring...
-
Page 67: Limited Warranty
Limited Warranty Limited Warranty NOTIFIER® warrants its products to be free from defects in materials and workmanship for eighteen (18) months from the date of manufacture, under normal use and service. Products are date stamped at time of manufacture. The sole and exclusive obligation of NOTIFIER® is to... - Page 68 World Headquarters NOTIFIER is a company. 12 Clintonville Road Northford, CT 06472-1653 USA 203-484-7161 fax 203-484-7118 www.notifier.com...