Dual Control Head Remote Kit; Installing The Krk-6Dh Main Panel Onto The Transceiver; Installing Two Krk-6Dh Rear Panels Onto Two Front Panel Kits - Kenwood TK-5710 Service Manual

( )
TK-5710 B

3. Dual Control Head Remote Kit

(KRK-6DH:Option)
The KRK-6DH remote kit connects two displays (two
KCH-14s or KCH-15s) to the transceiver. The KRK-6DH is
connected to the KCH-14s or KCH-15s with two optional
control cables. There are three version of the control cable :
KCT-22M (8 feet), KCT-22M2 (17 feet), and KCT-22M3 (25
feet).
3-1. Installing the KRK-6DH main panel onto the
transceiver
1. Remove the upper case and lower case of the trans-
ceiver.
2. Insert the lead wire with connector (W700) of the control
unit (X53-412) into the connector (CN4) of the KRK-6DH.
Insert the lead wire with connector (W104) of the KRK-
6DH into the connector (CN724) of the transceiver.
3. Install the KRK-6DH main panel on the transceiver using
four screws (z).
Note:
Take care that the lead wire with connector (W700) is not
caught when fitting the KRK-6DH main panel on the
transceiver.
4. Affixing the sheet (G11-4379-04) for the waterproof
(Fig.3-1-2).
(1) Remove the covering paper of the sheet (x).
(2) Affix the sheet while taking note of the position of the
three parts as shown in Fig.3-1-2 (c).
Firmly affix the sheet to the chassis by pushing the
double-coated tape with your fingers.
(3) Repeat step (2) to affix the sheet to the other side of
chassis.
Note:
The sheet cannot be reused. Affix a new sheet when you
removed the sheet.
5. Reassemble the upper case and lower case of the
transceiver. (Refer to page 24)
Note:
Take care that the sheet (G11-4379-04) is not peeled off
when installing the upper / lower case.
14
( )
/5710H B
INSTALLATION
Transceiver
CN724
W104
1
W700
CN4
CN5
KRK-6DH
main panel
Fig. 3-1-1
KRK-6DH main panel
Affix the sheet while
taking note of the position
of the three parts.
Fig. 3-1-2
3-2. Installing two KRK-6DH rear panels onto two
front panel kits
Install each KRK-6DH rear panel onto each front panel kit
as same as "2-2.Install the KRK-5 rear panel onto the front
panel kit" described on page 13.
3-3. Control cable (KCT-22) connection (Fig. 3-2)
1. Use two control cables. Insert one connector of the one
control cable to the transceiver (with KRK-6DH) and the
other to the display 1.
Insert one connector of the other control cable to the
transceiver (with KRK-6DH) and the other to the display 2.
Connect each cable to the GND terminal with the screws
(z) supplied with each control cable.
2. Secure the one connector of each control cable to the
KRK-6DH main panel with two screws (x) according to
the installation condition of the transceiver. Pass the
control cables through the grooves at both ends of the
KRK-6DH main panel and secure the control cables to the
KRK-6DH with the cable fitting (J21-4354-04) and two
screws (c) supplied with the KRK-6DH.
3. Secure the other connectors of the control cables to the
display 1 and display 2 with two screws (v) in the same
way.
1
2
3