NEC Univerge SV8100 System Maintenance Manual page 72

Issue 1.0
* NwInfo> CNETWORK_MAIN is called.[7c01]
* NwInfo> cnetwork_pro07 is called
* NwInfo> Process comes to exception procedure. (event:0990)
cnetmain src:7c01 oldSrcPort:0401->src_port_w:0401 rsrc:1(H323)
* NwInfo> CNETWORK_MAIN is called.[7c01]
* NwInfo> Process comes to exception procedure. (event:001c)
* NwInfo> create_network_packet( rsrc_id_w:1 bid:7 rsrc:1 line:1)
* NwInfo> Networking Resource type is H.323 Interface
* NwInfo> send user to user information message... CR:6
cnetmain src:7c01 oldSrcPort:0401->src_port_w:0401 rsrc:1(H323)
* NwInfo> IP Address: 0f0010ac
* NwInfo> Port: 1730
* NwInfo> CNETWORK_MAIN is called.[7c01]
* NwInfo> cnetwork_pro07 is called
* NwInfo> get_inter_signal_target( 0810H ) called
* NwInfo> send_internal_signal : target=0401 third=0000
response_while_frouting Selfport = 7c01 Target = 401 signal = 810
* NwInfo> create_network_packet( rsrc_id_w:1 bid:7 rsrc:1 line:1)
* NwInfo> Networking Resource type is H.323 Interface
* NwInfo> Status is changed...(7c01) 0024 -> 0011
cnetmain src:7c01 oldSrcPort:0401->src_port_w:0401 rsrc:1(H323)
* NwInfo> CNETWORK_MAIN is called.[7c01]
* NwInfo> T305 TIMER CLEAR !!!
* NwInfo> cnetwork_pro10 is called
* NwInfo> get_inter_signal_target( 0804H ) called
* NwInfo> send_internal_signal : target=0401 third=0000
response_while_frouting Selfport = 7c01 Target = 401 signal = 804
* NwInfo> create_network_packet( rsrc_id_w:1 bid:7 rsrc:1 line:1)
* NwInfo> Networking Resource type is H.323 Interface
* NwInfo> Status is changed...(7c01) 0011 -> 00c3
cnetmain src:7c01 oldSrcPort:0401->src_port_w:0401 rsrc:1(H323)
* NwInfo> IP Address: 0f0010ac
* NwInfo> Port: 1730
* NwInfo> CNETWORK_MAIN is called.[7c01]
* NwInfo> T305 TIMER CLEAR !!!
* NwInfo> cnetwork_pro19 is called
* NwInfo> -- network(0) VMI mode=0
* NwInfo> -- network(0) VMI port=0000h
* NwInfo> -- network(0) VMI third=0000h
* NwInfo> *** atrk_release_req : target_port_w = 0401H
* NwInfo> Release resource information : 1(01h)CALLED
clr_conf_system_id_on_cnetport() src_port=7c01
* NwInfo> *=* Call Information Clearing Complete.[7c01] *=*
* NwInfo> Status is changed...(7c01) 00c3 -> 0000
* NwInfo> Invalid parameter [netport_rsrc_type_read]
cnetmain src:7c01 oldSrcPort:0401->src_port_w:0000 rsrc:0(ISDN)
HP_LCD_REQ(0401,0001,0000,0000,0000)
ACD Data Size error. or socket close...
* NwInfo> CNETWORK_MAIN is called.[7c01]
3 - 32
status 0024 -> 0024
status 0024 -> 0024
status 0024 -> 0011
status 0011 -> 00c3
status 00c3 -> 0000
UNIVERGE SV8100