GIRBAU HS-5008 Instructions Manual
  1. Manuals
  2. Brands
  3. GIRBAU Manuals
  4. Washer
  5. HS-5008
  6. Instructions manual
GIRBAU HS-5008 Instructions Manual

GIRBAU HS-5008 Instructions Manual

Replacing the bearings
Hide thumbs Also See for HS-5008:
Table of Contents

Advertisement

Quick Links

Instructions for replacing the
bearings on washers
HS-5008 / H5020
GIRBAU, S.A.
Crta de Manlleu, km. 1
08500 VIC (Barcelona) • SPAIN
Tel. 34 93 8861100
Fax 34 93 8860785
girbau@girbau.es
www.girbau.com
For USA and CANADA:
CONTINENTAL GIRBAU Inc.
2500 State Road 44
WI 54904 Oshkosh • USA
Tel. 1(920) 231-8222
Fax 1(920) 231-4666
info@cont-girbau.com
www.cont-girbau.com
BEARING
REPLACEMENT
HS-5008
H5020
Rev. 00
Model
From Serial #
HS-5008
886.068
H5020
1.340.001
Cod. 409748 Bearing
Rev. 00/0204

Advertisement

Table of Contents
loading

Related Manuals for GIRBAU HS-5008

Summary of Contents for GIRBAU HS-5008

  • Page 1 Model From Serial # HS-5008 886.068 H5020 1.340.001 Instructions for replacing the bearings on washers HS-5008 / H5020 BEARING GIRBAU, S.A. REPLACEMENT Crta de Manlleu, km. 1 08500 VIC (Barcelona) • SPAIN HS-5008 Tel. 34 93 8861100 H5020 Fax 34 93 8860785 girbau@girbau.es...

  • Page 2: Safety Instructions

    Bearings Replacement SAFETY INSTRUCTIONS INDEX SAFETY INSTRUCTIONS 1. Preparation IMPORTANT 1.1. Variants of bearings’ box. The operations described in these instructions are 1.2. Necessary tools restricted to the Authorised Service 1.3. Pieces and materials 1.4. Parts 1.5. Emptying the residual bath WARNING!! 1.6.
  • Page 3 Bearings Replacement • BEARING BOX WITH DRAINAGE PREPARATION OUTLET. ACHINES MANUFACTURED WITH SERIAL 1.1 Variants of bearings’ box 887034 NUMBER FROM NUMBER ONTINENTAL MODELS MACHINES IMPORTANT MANUFACTURED WITH SERIAL NUMBER ’ HERE ARE TWO VARIANTS OF BEARINGS 1343435). F FROM NUMBER OR CHANGING BOXES MACHINES...

  • Page 4: Necessary Tools

    Bearings Replacement 1.2. Necessary tools DISASSEMBLY TOOLS AND EQUIPMENT ASSEMBLY Lower front and rear covers TORX 20 screwdriver (according to manufacturing TORX 25 screwdriver series) 5mm. flat screwdriver Front panel of the washing Wrench for opening the control panel machine 10mm.

  • Page 5: Parts List

    Bearings Replacement 1.4. Parts list MACHINES WITHOUT DRAINAGE MACHINES WITH DRAINAGE Cod. 409748 Bearing Rev. 00/0204...
  • Page 6 Bearings Replacement 1.5. Emptying the residual bath Before acting upon the washing machine. • Situate the outer, horizontal drainpipe tube onto the floor (machines with pump drainage) and place a recipient under it for collecting the water that can come out. •...
  • Page 7 Bearings Replacement Open the control panel of the washing machine using the security wrench that is provided with the machine. Take out the four screws that fasten the front panel of the washing machine and remove it from the machine. The location of the screws is indicated by means of the arrows in figure 5.

  • Page 8: Changing The Bearings

    Bearings Replacement MACHINE WITHOUT DRAINAGE. ACTION 2.1. Disassembling the bearings’ box. Note down the position of the level sensor tube in order to put it back during assembly. Note down the position of the screws and washers in order to put them back during assembly. Take out the A screws (fig.
  • Page 9 Bearings Replacement Introduce the separator into the bearings’ box and position it over the UM-542 centering tool. The conical side facing outward (fig. 11). fig. 11 Position the rear bearing in its housing (the numbered face of the bearing in the external part). Introduce it up to the end of the separator using the UM-499 tool (fig.
  • Page 10 Bearings Replacement If superficial scratches are observed, they can be smoothed with a polishing pad (Scotch Britte type) with a very fine grain. Never use abrasive products with emery-type course grain. At the rear face of the back of the outer drum, clean the inside of the central fastening disk of the bearings’...
  • Page 11 Bearings Replacement Fasten the center of the bearings’ box to the center of the back of the outer drum by means of the A screws and the corresponding washers (fig. 19). Do not tighten. Fasten the ends of the bearings’ box to the edge of the outer drum by means of the B screws and the corresponding nuts and washers (fig.
  • Page 12 Bearings Replacement Lean the conical trunk end of the bearings’ box on a hard, clean and flat surface. Position the front bearing in its housing (the numbered side of the bearing in the external part). Introduce it up to the end of the box using the UM- 500 tool (fig.
  • Page 13 Bearings Replacement Turn the bearings’ box around again. Spread a silicon string of about 0,2 inch / 5mm in diameter in order to seal the drainage outlet. See the layout of the silicon string in figure 27. IMPORTANT The layout of the silicon string should correspond to the layout in the figure and should not obstruct the drainage outlet fig.
  • Page 14 Bearings Replacement Place the flat joint starting from the welding points indicated in figure 31. IMPORTANT The position of the flat joint should allow the drainage of the bearings’ box. In case of improper placement, drainage will not be effective. fig.

  • Page 15: Changing The Seals

    Bearings Replacement 4. Changing the seals. Remove the old seals. TOTALLY clean the housing of the seals. The contact of the seals with the TOTALITY of its housing surface area is essential. DO NOT LUBRICATE the housings of the seals. Mount the inner seal.
  • Page 16 Bearings Replacement 5 ASSEMBLY AND VERIFICATION 5.1. Assembling the drum. Introduce the end of the drum into the outer drum. Avoid letting the axle strike or scrape against the back of the outer drum. Center the axle with bearings and introduce it up to the back.

  • Page 17: Checking The Machine

    Bearings Replacement Tighten the lower area of the ring with the grip pliers (fig. 43). If you have more than one plier, place them in the lower area of the ring. Tighten the joint screw of the ring. 5.3. Assembling the front panel of the washing machine.

This manual is also suitable for:

H5020

Table of Contents