Safety Instructions WARNING! IMPORTANT SAFETY INSTRUCTIONS WARNING: To reduce the risk of fire, electric shock or injury to persons when using the washer, follow basic precautions, including the following: READ all instructions before using the washer and 12. Failure to install and operate this machine KEEP them in a prominent location for customer according to the Instruction Handbooks or to work use.
Page 3
(1) Qualified Personnel refers to anyone who has read the Instructions Handbooks, has been trained and has a thorough understanding of the machine’s operation (2) An Authorised Service Technical (STA) is one that has successfully completed training on the product by Girbau S.A., or a Girbau, S.A. Distributor.
Page 4
Any part you may replace on your washing machine, must be an ORIGINAL SPARE-PART • Glass. official GIRBAU. Otherwise the machine can suffer The chemicals furnisher and the machine owner damages and may be dangerous for its safety. will be responsible to assure that the products ARE...
, can be consulted at the manufacturer’s Britain application website: www.girbau.com, see Advanced Operation 2.2.5 Phases definition Instructions rev. 02 for HS-5008 LOGI CONTROL. 2.2.6 Definition of programmable functions and values for each phase 2.2.7 Modification of a program 2.3. Information menu. Info menu 2.4.
Operation 1. OPERATING INSTRUCTIONS recommend mixing whites with other colours or garments of different colours. Open the door and load the machine. We recommend 1.1. Control panel filling the drum to its nominal load. Do not overload the machine; the door must be able to close easily. Whilst the door is open, the display reads door, indicating that the door must be closed in order for the program to begin.
Operation 1.4 Starting a program Load the machine and close the door (see section 1.2). Choose the desired program with the programme selection buttons. (For information characteristics of each program, please see section 1.6. Wash Programs). The selected program will be shown on the display.
- - - - - - - - - - - - The parameters that appear on the chart can be modified: See the Advanced Operation Instructions rev. 02 for HS-5008 www.girbau.com LOGI CONTROL at the manufacturer’s website: Cod. 410746...
Page 9
- - - - - - - - - - - - The parameters that appear on the chart can be modified: See the Advanced Operation Instructions rev. 02 for HS-5008 www.girbau.com LOGI CONTROL at the manufacturer’s website: Cod. 410746...
Page 10
- - - - - - - - - - - - The parameters that appear on the chart can be modified: See the Advanced Operation Instructions rev. 02 for HS-5008 www.girbau.com LOGI CONTROL at the manufacturer’s website: Cod. 410746...
Operation 1.6.2. Description of symbols and values of programs charts SYMBOL OPTION DESCRIPTION Estimated program time Minimum program time based on a machine with hot water supply and without heating. Time in minutes. Phase number. The phase indicated with grey background belongs to the wash phase. Bath level Low level Medium level...
Advanced Operation Instructions for 1.9 The DELAY option HS-5008 LOGI CONTROL, rev. manufacturer’s website: www.girbau.com. The DELAY option allows you to program the start time of a program in progress depending on the needs of the Cod. 410746 Rev. 02/0804...
Troubleshooting 3. TROUBLESHOOTING ...there is a water leak. - Check the status of the output draining pipe. - Check the status of the seals on the water inlet Some of the washing machine’s operating problems hoses; tighten the connectors. can be solved through the intervention of the user. - Clean the door seal of any possible deposits or These problems are detailed below.
Maintenance 4. MAINTENANCE Check the temperature of the hot water hose, so as to avoid the risk of burns. Disassemble the fittings that connect the hoses to the washing machine. Before performing any work on the washing Remove the filters from their housings inside the machine, disconnect and mechanically lock the washing machine, using pliers to pull on the central external switch, and close and mechanically...
Maintenance / Service removal 4.6. Cleaning the drain pump 5. SERVICE REMOVAL Tools required: Disassembly of the lower front panel: slotted Removing the washer from service requires a screwdriver: 5mm. specialised company. Before disassembling the lower front panel of the Never release the washer unsecured.
Page 16
- - - - - - - - - - - - The parameters that appear on the chart can be modified: See the Advanced Operation Instructions rev. 02 www.girbau.com for HS-5008 LOGI CONTROL at the manufacturer’s website: Cod. 410746 Rev. 02/0804...