Table of Contents
Advertisement
Command and Response Table for SIS Commands
Command
Create ties
NOTES:
•
Commands can be entered back-to-back in a string, with no spaces. For example: 1*1!02*02&003*003%4*24!.
•
The matrix switchers support 1-, 2-, and 3-digit numeric entries (1*1!, 02*02&, or 003*003%).
•
The ! tie command, the & tie command, and the % tie command can be used interchangeably, as can the ! read tie command, the &
tie command, and the % read tie command.
X!
X@
to output
Tie input
Example (see Note, above):
X!
X@
Tie input
to output
Example (see Note, above):
X!
X@
Tie input
to output
,
Example (see Note, above):
Read output tie
Read output tie
Read output tie
Channel mutes
Channel mute
Channel unmute
Read channel mute
Global channel mute
Global channel unmute
NOTE:
• = Space
X!
= Input number
X@
= Output number
X%
= Mute
Command
Save and recall presets
NOTE: If you try to recall a preset that is not saved, the matrix switcher responds with the error code E11.
Save current configuration as a
global preset
Example:
Recall a global preset
Example:
IP setup
Set IP address
Read IP address
Set DHCP on or off
Read DHCP on/off status
X$
NOTE:
= Global preset number
X^
IP address
=
X&
DHCP
=
ASCII Command
Response
(Host to Unit)
(Unit to Host)
X!
X@
*
!
Out
1*3!
Out03
X!
X@
*
&
Out
10*4&
Out04
X!
X@
*
%
Out
7*5%
Out05
X@
X!]
&
X@
X!]
%
X@
X!]
!
X@
*1B
Vmt
X@
*0B
Vmt
X@
X%]
B
1*B
Vmt1
0*B
Vmt0
00 – maximum number of inputs for your configuration (00 = untied)
01 – maximum number of outputs for your configuration
1 = mute on, 0 = mute off
ASCII Command
Response
(Host to Unit)
(Unit to Host)
X$
,
Spr
9,
Spr09
X$
.
Rpr
5.
Rpr05
EX^
}
CI
Ipi
E
}
X^]
CI
EX&
}
DH
Idh
E
}
X&]
DH
01 – 64
nnn.nnn.nnn.nnn
0
= off,
1
= on
Additional Description
X@
X!
]
In
All
•
•
Tie input
]
Tie input 1 to output 3.
In01
All
•
•
X@
X!
]
In
RGB
•
•
Tie input
]
Tie input 10 to output 4.
In10
RGB
•
•
X@
X!
]
In
Vid
•
•
Tie input
]
Tie input 7 to output 5.
In07
Vid
•
•
X!
Input
X!
Input
X!
Input
X@
]
*1
Mute output
output remains active).
X@
]
*0
Unmute output
1 = mute on, 0 = mute off.
]
Mute all light outputs.
]
Unmute all light outputs.
Additional Description
X$]
Command character is a comma.
]
Save current ties as preset 9.
X$]
Command character is a period.
]
Recall preset 5, which becomes the current
configuration.
X^]
X&]
X!
X@
to output
.
X!
X@
to output
.
X!
X@
to output
.
X@
is tied to output
.
X@
is tied to output
.
X@
is tied to output
.
X@
(no signal is output, but the light
X@
(signal is output).
Advertisement
Table of Contents
