Mazda RX-8 2004 Service Highlights page 386

WDS
display
B2867 31
U2017 43
U2018 44
PID/Data Monitoring Function
• By using the PID/data monitoring function, the monitored item of the input/output signal, as set on the SAS
control module, can be freely selected and read out in real-time.
• The WDS or equivalent is used to read out PID/data monitor information.
PID/data monitor table
PID name (definition)
CCNT_RCM
(Number of continuous DTCs)
D_ABAGR2
(Driver-side air bag module
(inflator No.2) resistance)
D_CRSH_S
(Driver-side side air bag
sensor status)
DABAGR
(Driver-side air bag module
(inflator No.1) resistance)
D_PTENSFLT
(Driver-side pre-tensioner seat
belt circuit status)
DR_BUKL
(Driver-side buckle switch
status)
DR_CURTN
(Driver-side curtain air bag
module resistance)
DR_PTENS
(Driver-side pre-tensioner seat
belt resistance)
DS_AB
(Driver-side side air bag
module resistance)
DS_AB_ST
(Driver-side side air bag
module circuit status)
DS_CURT_ST
(Driver-side curtain air bag
module circuit status)
ON-BOARD DIAGNOSTIC
DTC
Air bag system warning light
Flashing pattern
Unit/Condition
• DTCs detected: 1—255

• No DTCs detected: 0
Ohms Under any condition: 1.5—3.7 ohms
• Sensor normal: OK
OK/
• Sensor communication error: COMM_FAIL
COMM_FAIL/
• Sensor internal circuit abnormal: INT_FAIL
INT_FAIL
Ohms Under any condition: 1.5—3.7 ohms
• Related wiring harness normal: NORMAL
NORMAL/
• Related wiring harness circuit open: OPEN
OPEN/
• Related wiring harness short to ground: SHRT_GND
SHRT_GND/
• Related wiring harness short to power supply: SHRT_B+
SHRT_B+/
• Pre-tensioner seat belt circuit resistance low:
SQ_LOWRES
SQ_LOWRES
• Driver-side buckle switch on: Buckled
Buckled/
• Driver-side buckle switch off: Unbuckled
Unbuckled
Ohms Under any condition: 1.4—3.2 ohms
Ohms Under any condition: 1.5—3.1 ohms
Ohms Under any condition: 1.4—3.2 ohms
• Related wiring harness normal: NORMAL
NORMAL/
• Related wiring harness circuit open: OPEN
OPEN/
• Related wiring harness short to ground: SHRT_GND
SHRT_GND/
• Related wiring harness short to power supply: SHRT_B+
SHRT_B+/
• Air bag module circuit resistance low: SQ_LOWRES
SQ_LOWRES
• Related wiring harness normal: NORMAL
NORMAL/
• Related wiring harness circuit open: OPEN
OPEN/
• Related wiring harness short to ground: SHRT_GND
SHRT_GND/
• Related wiring harness short to power supply: SHRT_B+
SHRT_B+/
• Air bag module circuit resistance low: SQ_LOWRES
SQ_LOWRES
System malfunction location
Priority
ranking
Poor connection of any SAS control module
6
connectors
Driver-side side air bag sensor (communication
8
error)
Passenger-side side air bag sensor
7
(communication error)
Operation Condition (Reference) Terminal

08–02
1G, 1J
2Z, 2AA
1S, 1V
2P, 2S
2T
2V, 2Y
2P, 2S
2M, 2O
2M, 2O
2V, 2Y
08–02–5