Page 1: Table Of Contents
Table of Contents Introduction Instrument Cluster Warning and control lights Gauges Entertainment Systems AM/FM stereo with CD AM/FM stereo with cassette and in-dash six CD Climate Controls Manual heating and air conditioning Lights Headlamps Turn signal control Bulb replacement Driver Controls Windshield wiper/washer control Steering wheel adjustment Power windows...
Page 2 Table of Contents Brakes Transmission operation Vehicle loading Trailer towing Recreational towing Roadside Emergencies Hazard flasher switch Fuses and relays Overheating Jump starting Wrecker towing Customer Assistance Reporting safety defects (U.S. only) Cleaning Maintenance and Specifications Engine compartment Engine oil Battery Fuel information Air filter(s)
Page 3: Introduction
The more you know and understand about your vehicle, the greater the safety and pleasure you will derive from driving it. For more information on Mazda and its products visit the following website: In the United States: www.mazdausa.com In Canada: www.mazda.ca...
Page 4: Safety And Environment Protection
Introduction SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury and prevent possible damage to others, your vehicle and its equipment? In this guide, answers to such questions are contained in comments highlighted by a bold WARNING statement. These comments should be read and observed.
Page 5: Special Notices
SPECIAL NOTICES Event Data Recorder The computer in your vehicle is capable of recording detailed data potentially including but not limited to information such as: the use of restraint systems including seat belts by the driver and passengers, information about the performance of various systems and modules in the vehicle, and information related to engine, throttle, steering, brake or other system status potentially including information related to how the driver...
Page 6 Introduction These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert Protecting the Environment Air Bag-Front Child Seat Child Seat Lower Anchor Brake System Brake Fluid - Non-Petroleum Based Hazard Warning Flasher Fuse Compartment Windshield Wash/Wipe Rear Window Defrost/Demist...
Page 7 Passenger Compartment Air Filter Check fuel cap INFORMATION ABOUT THIS GUIDE The information found in this guide was accurate at the time of printing. Mazda may change the contents without notice. Introduction Personal Alarm System Feature Engine Coolant Do Not Open When Hot...
Page 8 Instrument Cluster Instrument Cluster Windshield wiper/washer Headlamp and turn control signal control (pg. 56) (pg. 48) Instrument cluster Fog lamp control* (pg. 10) (pg. 48) Power mirror control* Speed controls* (pg. 62) (pg. 63) Instrument panel Driver air bag dimmer/dome light (pg.
Page 9 Instrument Cluster Rear window defroster Audio system control Hazard flasher control (pg. 17) (pg. 47) (pg. 157) 4WD control* (pg. 138) Cigarette lighter Climate controls (pg. 44) Auxiliary power point (pg. 60) *if equipped...
Page 10: Instrument Cluster
Instrument Cluster WARNING LIGHTS AND CHIMES CHECK FUEL Warning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’s functions. Many lights will illuminate when you start your vehicle to make sure the bulb works.
Page 11 2. Poor fuel quality or water in the fuel. 3. The fuel cap may not have been properly installed and securely tightened. These temporary malfunctions can be corrected by filling the fuel tank with high quality fuel of the recommended octane and/or properly installing and securely tightening the fuel cap.
Page 12 Mazda dealer. Normal braking is still functional unless the brake system warning light also is illuminated. WARNING: If the light remains on, continues to flash or fails to illuminate, have the system serviced immediatelyby an authorized Mazda dealer.
Page 13 ON, continues to flash or remains on, have the system serviced immediately by an authorized Mazda dealer. A chime will also sound when a malfunction in the supplemental restraint system has been detected.
Page 14 Illuminates when four-wheel drive is engaged, refer to the Driving chapter. Note: If the light continues to flash, have the system serviced by an authorized Mazda dealer. Anti-theft system: Flashes when the Securilock Passive Anti-theft System has been activated. Refer to...
Page 15: Gauges
GAUGES CHECK FUEL Speedometer: Indicates the current vehicle speed. Engine coolant temperature gauge: Indicates engine coolant temperature. At normal operating temperature, the needle will be in the normal range (between “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine and let the engine cool.
Page 16 Instrument Cluster Odometer: Registers the total kilometers (miles) of the vehicle. Trip odometer: Registers the kilometers (miles) of individual journeys. Press and hold the button for 1 or more seconds to reset. Press and release the button in less than 1 second to toggle between odometer and trip odometer.
Page 17: Entertainment Systems
Entertainment Systems Entertainment Systems AM/FM RADIO WITH COMPACT DISC PLAYER Volume/power control Ensure that the ignition is either in the ACC or ON position for the audio system to function. Press the control to turn the audio system on or off. Turn the control to raise or lower the volume.
Page 18 Entertainment Systems AM/FM select Ensure that the ignition is in the ACC or ON position for the radio to operate. Press the AM or FM1/2 control to enter radio mode. Band selection Select AM by pressing the AM button and FM1 or FM2 by pressing the FM1/2 button.
Page 19 Turn the TUNE control to the left for a lower frequency. Turn the TUNE control to the right for a higher frequency. Scan function The scan function works in radio and CD mode. Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band.
Page 20 Entertainment Systems Treble adjust The treble adjust control allows you to increase or decrease the audio system’s treble output. Press the audio control until TREB is displayed. Turn the control to increase (right) or decrease (left) the amount of treble output. Bass adjust The bass adjust control allows you to increase or decrease the audio system’s bass output.
Page 21 Entertainment Systems Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. Press the audio control until FADE appears. Turn the control (right or left) to adjust between the front and rear speakers. Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers.
Page 22 Entertainment Systems Press the audio control until MID appears in the display. Turn the control to the right to increase the mid-range. Turn the control to the left to decrease the mid-range. The level will display. Release the TUNE control when the desired level is reached.
Page 23 Starting autoset memory preset 1. Press the AM or FM1/2 control to select a frequency. 2. Press and momentarily hold the AUTO-M (Auto memory) control. The system will beep. 3. When the first six strong stations are filled, the strongest station will start playing.
Page 24 Entertainment Systems Press the VOL (Volume) control to stop cassette play. CD select To begin CD play: 1. Insert a CD into the slot, label side up. The system will auto-load the CD and begin play after a short pause. The disc number and the track number will illuminate in the display.
Page 25 Track search Track search works in CD mode. Press the on the TRACK control to skip forward to the beginning of the next track. Press the on the TRACK control to skip back to the beginning of the current track. Disc search Disc search works in CD mode.
Page 26 Entertainment Systems Random play in CD mode Press the RDM control during play. RDM will illuminate in the display. The next selection will be randomly selected. To disengage random play, press the RDM control again. Setting the clock The clock can be set at any time when the ignition switch is in the ACC or ON position.
Page 27: Am/Fm Radio With Cassette Tape And Compact Disc Player/Changer (In-Dash Cd Changer)
Entertainment Systems Press the CLOCK control to alternate the display. NOTE: If the audio operation is selected while the clock mode is on, the selected audio mode will be displayed for ten seconds, then the display will revert to the clock mode. AM/FM RADIO WITH CASSETTE TAPE AND COMPACT DISC PLAYER/CHANGER (IN-DASH CD CHANGER) Volume/power control...
Page 28 Entertainment Systems Turn the control to raise or lower the volume. NOTE: To prevent the battery from being discharged, do not leave the audio system on for a long period when the engine is not running. NOTE: Once the system is turned off, press the VOL control again to listen to the frequency last tuned to.
Page 29 Entertainment Systems Press the TUNE control to select the desired function. Turn the TUNE control to adjust the desired levels. Refer to Treble adjust for specific instructions on level adjustments. The TUNE control will also work in radio mode to manually increase or decrease the frequency.
Page 30 Entertainment Systems Scan function in CD mode Press the SCAN control during CD play to hear the first ten seconds of each track. Press the SCAN control again to stop the scan mode. NOTE: If the unit is left in scan mode, normal play will resume where scan was selected.
Page 31 Entertainment Systems Bass adjust The bass adjust control allows you to increase or decrease the audio system’s bass output. Press the audio control until BASS appears. Turn the control to increase (right) or decrease (left) the amount of bass output. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers.
Page 32 Entertainment Systems Press the audio control until BAL appears. Turn the control (right or left) to adjust between the right and left speakers. Mid-range adjust (if equipped) Your vehicle may be equipped with a mid-range adjust. The TUNE control allows you to adjust the mid-range levels. Press the audio control until MID appears in the display.
Page 33 Radio station memory preset The radio is equipped with six station memory preset controls. These controls can be used to select up to six preset AM stations and 12 FM stations (six in FM1 and six in FM2). Setting memory preset stations 1.
Page 34 Entertainment Systems NOTE: If the power supply is interrupted, (fuse blows or the battery is disconnected), the preset channels will be canceled. Tape select (if equipped) To begin tape play, insert a cassette tape into the cassette slot, with the open edge facing the right.
Page 35 Tape direction select Press the PROG RDM control to play the alternate side of a tape. NOTE: When the end of the cassette is reached, the audio system will automatically reverse play. Repeat play The repeat play feature works in tape and CD modes and allows you to listen to a selection repeatedly.
Page 36 Entertainment Systems Track search Track search works in CD mode. Press the on the TRACK control to skip forward to the beginning of the next track. Press the on the TRACK control to skip back to the beginning of the current track.
Page 37 APC in tape mode Press the APC control to advance to the beginning of the next selection. Press the APC control to reverse to the beginning of the current selection. To disengage APC, press the APC control again. If APC detects 15 seconds of blank space, it will automatically advance the tape to the next selection.
Page 38 Entertainment Systems Inserting CDs into desired tray number 1. Press and hold the LOAD control until a beep sound is heard. 2. Press the memory preset control for the desired CD tray within 5 seconds after the beep is heard. 3.
Page 39 Multiple ejection 1. Press and hold the CD eject control for approximately 2 seconds until a beep sound is heard. 2. Wait approximately 5 seconds or press the CD eject control again within 5 seconds after the beep is heard. 3.
Page 40 Entertainment Systems 2. Press SCAN on the hour set control to adjust the hours. 3. Press AUTO-M on the minute set control to adjust the minutes. 4. Press the CLOCK control again to start the clock. NOTE: If the power supply to the unit is interrupted (if the fuse blows or the vehicle’s battery is disconnected), the clock will need to be reset.
Page 41 Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Mazda CD players. Irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player.
Page 42: Radio Frequency Information
(4.75 in) audio compact discs only. Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Mazda CD players. Irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player.
Page 43 Radio reception factors Three factors can affect radio reception: Distance/strength. The further an FM signal travels, the weaker it is. The listenable range of the average FM station is approximately 40 km (24 miles). This range can be affected by “signal modulation.” Signal modulation is a process radio stations use to increase their strength/volume relative to other stations.
Page 44: Climate Controls
Climate Controls Climate Controls MANUAL HEATING AND AIR CONDITIONING SYSTEM Fan speed control Controls the volume of air circulated in the vehicle. Temperature control knob Controls the temperature of the airflow inside the vehicle. Mode selector control Controls the direction of the airflow to the inside of the vehicle.
Page 45 Climate Controls MAX A/C- Uses recirculated air to cool the vehicle. MAX A/C is noisier than A/C but more economical and will cool the inside of the vehicle faster. Airflow will be from the instrument panel registers. This mode can also be used to prevent undesirable odors from entering the vehicle.
Page 46 Climate Controls Operating tips In humid weather conditions, place the climate control system in Defrost mode before driving. This will reduce fogging on your windshield. Once the windshield has been cleared, operate the climate control system as desired. To reduce humidity buildup inside the vehicle in cold weather conditions, don’t drive with the climate control system in the OFF or MAX A/C position.
Page 47 4. Direct the outer panel vents towards the side windows. 5. To increase airflow to the outer panel vents, close the central panel vents. WARNING: Do not place objects on top of the instrument panel as these objects may become projectiles in a collision or sudden stop.
Page 48: Lights
Lights Lights HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, license plate lamps and tail lamps. Turns the headlamps on. BATTERY SAVER Your vehicle is equipped with a battery saver feature which, if you leave the headlamps on, automatically turns off the headlamps after 30 seconds when the ignition is in the OFF position.
Page 49: Instrument Panel Dimmer Control
High beams After turning the headlamps on, push the lever toward the instrument panel to activate. Pull the lever towards you to deactivate. Flash to pass Pull toward you slightly to activate and release to deactivate. INSTRUMENT PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel.
Page 50: Aiming The Headlamps
The headlamps on your vehicle are properly aimed at the assembly plant. If your vehicle has been in an accident the alignment of your headlamps should be checked by your authorized Mazda dealer. TURN SIGNAL CONTROL Push down to activate the left turn signal.
Page 51: Bulb Replacement
Check the operation of the following interior bulbs frequently: interior overhead lamp map lamp For bulb replacement, see an authorized Mazda dealer. Using the right bulbs Replacement bulbs are specified in the chart below. Headlamp bulbs must be marked with an authorized “D.O.T.” for North America to assure lamp performance, light brightness and pattern and safe visibility.
Page 52 To replace all instrument panel lights - see your dealer. Replacing headlamp bulbs NOTE: This procedure can be difficult. Your Mazda dealer has the proper tools, training and parts to perform this task. If you have difficulty with this procedure, visit your local Mazda dealer.
Page 53 3. Disconnect the electrical connector from the bulb by pulling rearward. 4. Remove the rubber boot from the lamp assembly by pulling on one of the tabs. 5. Squeeze the retainer spring together releasing it from bulb hooks and rotate it away from the bulb.
Page 54 Lights Replacing brake/tail/turn/backup lamps bulbs The brake/tail/turn/backup lamp bulbs are located in the tail lamp assembly, one just below the other. Follow the same steps to replace either bulb: 1. Open the liftgate to expose the lamp assemblies. 2. Remove the two screws from the lamp assembly.
Page 55 4. Install the bulb socket in lamp assembly turning it clockwise, 5. Install the lamp assembly on liftgate with two screws. Replacing high-mount brake lamp bulbs For bulb replacement, see an authorized Mazda dealer. Lights...
Page 56: Driver Controls
Driver Controls Driver Controls MULTI-FUNCTION LEVER Windshield wiper: For intermittent operation, move control down one position. Adjust the rotary control to the desired speed setting. For normal or low speed wiper operation, move control down two positions from OFF. For high speed wiper operation, move control down three positions from OFF.
Page 57 Driver Controls Rear window wiper/washer controls For intermittent operation of rear wiper, rotate end of control upward to the INT position. For normal speed rear wiper operation, rotate control upward to To activate the rear washer, rotate the control to the position and release.
Page 58: Overhead Console - If Equipped
Driver Controls Changing the wiper blades 1. Pull the wiper arm away from the vehicle. Turn the blade at an angle from the wiper arm. Push the lock pin manually to release the blade and pull the wiper blade down toward the windshield to remove it from the arm.
Page 59 Storage compartment (if equipped) Press the OPEN control to open the storage compartment. The door will open slightly and can be moved to full open. Installing a garage door opener (if equipped) The storage compartment can be converted to accommodate a variety of aftermarket garage door openers: Remove the Velcro pad (2) from the storage compartment door...
Page 60: Auxiliary Power Point
Driver Controls Approximate Thickness of Transmitter (GDO) inches Less Than 6.35 22.00 26.00 1–3/16 32.00 Reinstall the rubber actuator (1) in the storage compartment (7) by twisting and pushing it back into the slot. Install the transmitter (6) on to storage compartment door (3) aligning the actuator control (8) with the rubber plunger (1).
Page 61: Power Windows
The auxiliary power point is located on the instrument panel below the radio. Do not plug optional electrical accessories into the cigarette lighter. Use the power point. Do not use the power point for operating the cigarette lighter element. The Maximum power each power point can supply depends on the fuse rating.
Page 62: Mirrors
Driver Controls One touch down Allows the driver’s window to open fully without holding the control down. Press completely down on AUTO and release quickly. Press again to stop. Note: This feature will only operate the driver’s side window. Window lock The window lock feature disables all the power windows except the driver’s.
Page 63: Speed Control
To adjust your mirrors: 1. Rotate the control clockwise to adjust the right mirror and rotate the control counterclockwise to adjust the left mirror. 2. Move the control in the direction you wish to tilt the mirror. 3. Return to the center position to lock mirrors in place. Fold-away mirrors Pull the side mirrors in carefully when driving through a narrow...
Page 64 Driver Controls WARNING: Using cruise control in the following conditions could cause you to lose control of the vehicle: Heavy or unsteady traffic Slippery or winding roads Similar restrictions that require inconsistent speed Don’t use cruise control in these situations. Setting speed control The controls for using your speed control are located on the steering...
Page 65 Resuming a set speed Press the RSM (resume) control and release it. This will automatically return the vehicle to the previously set speed. The RSM control will not work if the vehicle speed is not faster than 48 km/h (30 mph). Increasing speed while using speed control There are two ways to set a higher speed:...
Page 66 Driver Controls Depress the brake pedal until the desired vehicle speed is reached, press the SET ACC control. Turning off speed control There are two ways to turn off the speed control: Depress the brake pedal or the clutch pedal (if equipped). This will not erase your vehicle’s previously set speed.
Page 67: Moonroof (If Equipped)
MOON ROOF (IF EQUIPPED) To operate the moon roof: The moon roof is equipped with an automatic, one-touch, express opening feature. Press and release the rear portion of the control. To stop motion at any time during the one-touch opening, press the control a second time.
Page 68: Cargo Shade (If Equipped)
Driver Controls CARGO SHADE (IF EQUIPPED) If your vehicle has a cargo shade, you can use it to cover items in the cargo area of your vehicle. To install the shade: Insert the ends of the cargo shade into the mounting features located behind the rear seat on the rear trim panels.
Page 69: Luggage Rack
WARNING: Make sure that the liftgate door and/or window are closed to prevent exhaust fumes from being drawn into the vehicle. This will also prevent passengers and cargo from falling out. If you must drive with the liftgate door or window open, keep the vents open so outside air comes into the vehicle.
Page 70: Locks And Security
Locks and Security Locks and Security KEYS The key operates all locks on your vehicle. In case of loss, replacement keys are available from your dealer. You should always carry a second key with you in a safe place in case you require it in an emergency.
Page 71: Remote Entry System (If Equipped)
Childproof door locks When these locks are set, the rear doors cannot be opened from the inside. The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located on rear edge of each rear door and must be set separately for each door.
Page 72 Locks and Security The remote entry system allows you to lock or unlock all vehicle doors without a key. The remote feature will only operate when the ignition is in the 1 (LOCK) or 2 (ACC) position. If there is a problem with the remote entry system make sure to take ALL remote entry transmitters with you to the...
Page 73 If you would like to have your remote entry transmitter reprogrammed because you lost one, or would like to buy additional remote entry transmitters, you can either reprogram them yourself, or take all remote entry transmitters to your authorized Mazda dealer for reprogramming. How to reprogram your remote entry transmitters You must have all remote entry transmitters (maximum of four) available before beginning this procedure.
Page 74 Locks and Security Note: This procedure must be completed within the specified times. If not completed within the specified time period, reprogramming procedures must be restarted from the beginning. To reprogram the remote entry transmitters: 1. Ensure the vehicle is electronically unlocked. 2.
Page 75: Anti-Theft System
If a problem occurs with the SecuriLock rapidly or glow steadily when the ignition is in the ON position. If this occurs, the vehicle should be taken to an authorized Mazda dealer for service. Locks and Security...
Page 76 If the indicator stays on for an extended period of time or flashes rapidly, have the system serviced by your authorized Mazda dealer. Replacement keys If your keys are lost or stolen and you don’t have an extra coded key, you will need to have your vehicle towed to a dealership.
Page 77 If you do not have at least 2 previously programmed keys, you must take your vehicle to your authorized Mazda dealer to have the spare key(s) programmed. 1. Insert a previously programmed coded key into the ignition.
Page 78: Perimeter Alarm System (If Equipped)
If failure repeats, bring your vehicle to your authorized Mazda dealer to have the new key(s) programmed. To program additional new unprogrammed key(s), repeat this procedure from step 1 for each additional key.
Page 79 Disarming the system You can disarm the system by any of the following actions: Unlock the doors by pressing the transmitter. Unlock the doors with a key. Pressing the control on the remote entry transmitter. This will disarm the system only if the alarm is sounding. Locks and Security control on your remote entry...
Page 80: Seating And Safety Restraints
Seating and Safety Restraints Seating and Safety Restraints SEATING Adjusting the front manual seat WARNING: Never adjust the driver’s seat or seatback when the vehicle is moving. Sudden braking or a collision could cause serious injury. Adjust the seat only when the vehicle is stopped. WARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injuring people in a collision or sudden stop.
Page 81 Seating and Safety Restraints Adjustable head restraints (if equipped) The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible.
Page 82 Seating and Safety Restraints Adjusting the front power seat (if equipped) WARNING: Never adjust the driver’s seat or seatback when the vehicle is moving. Sudden braking or a collision could cause serious injury. Adjust the seat only when the vehicle is stopped. WARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injuring people in a collision or sudden stop.
Page 83: Rear Seats
Seating and Safety Restraints Move the control in the directions shown to move the seat forward, backward, up or down. Heated seats (if equipped) To operate the heated seats: Push the control located on the seat to activate. Push again to deactivate. The heated seats will activate when the ignition is in the RUN position.
Page 84 Seating and Safety Restraints Push control to lower head restraint. Reclining the second row seatback Locate the release strip located on the outboard side of the seat cushion bottom and lift gently to allow the seatback to be adjusted to the desired position.
Page 85 Seating and Safety Restraints 2. Place the head restraints under the front passenger seat for storage. 3. Pull the seat release control. 4. Flip seat forward. 5. Pull the seatback release strap toward the front seat. Make sure the seat belt buckle heads are fully extended towards the front of the vehicle and are away from the seatback.
Page 86 Seating and Safety Restraints 6. Rotate seatback down into load floor position. WARNING: Make sure seat belt buckle heads are not trapped underneath the seatback and that the seat belt buckle heads are fully extended towards the front of the vehicle. Seat belt buckle heads may break if they are trapped underneath the seatback as the seatback is...
Page 87 Seating and Safety Restraints 2. Rotate seat cushion down into the seating position making sure that the seat cushion is locked into place and that the seat belt buckles are exposed. 3. Remove the head restraints stored under the front passenger seat and return them to the original position on the seat backs.
Page 88 Seating and Safety Restraints Folding down rear seats (bench) 1. Raise the rear seat head restraint and remove. 2. Place the head restraints under the front passenger seat for storage. 3. Pull the seat release control on each side of the seat to release the locks.
Page 89 Seating and Safety Restraints 5. Pull the seatback release strap toward the front seat. Make sure the seat belt buckle heads are fully extended towards the front of the vehicle and are away from the seatback. NOTE:When the seatback release strap is pulled use your other hand to guide the seatback.
Page 90: Safety Restraints
Seating and Safety Restraints To remove the rear cushion 1. Pull the Yellow tab 2. Pull the cushion so that the rods remove from the locking tabs. To install the rear cushion 1. Push the cushion so that the rods fit into the locking tabs. 2.
Page 91 Seating and Safety Restraints WARNING: All occupants of the vehicle, including the driver, should always properly wear their safety belts, even when an air bag (SRS) is provided. WARNING: It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.
Page 92 Seating and Safety Restraints This safety belt system has a retractor assembly that is designed to pay out webbing in a controlled manner. This feature is designed to help reduce the belt force acting on the occupant’s chest. WARNING: All safety belts should be checked for proper function.
Page 93 Seating and Safety Restraints 2. To unfasten, push the release button and remove the tongue from the buckle. The front outboard and rear outboard safety restraints in the vehicle are combination lap and shoulder belts. The front outboard passenger and rear seat outboard safety belts have two types of locking modes described below: Vehicle sensitive mode...
Page 94 WARNING: After any vehicle collision, the front passenger outboard seat belt system must be checked by an authorized Mazda dealership to verify that the “automatic locking retractor” feature for child seats is still functioning properly. In addition, all seat belts should be checked for proper function.
Page 95 Seating and Safety Restraints WARNING: BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED if the seat belt assembly “automatic locking retractor” feature or any other seat belt function is not operating properly when checked according to the procedures in Workshop Manual. WARNING: Failure to replace the Belt and Retractor assembly could increase the risk of injury in collisions.
Page 96 WARNING: Improper disposal of the pretensioner system or a vehicle with non-deactivated pretensioners is dangerous. Unless all safety procedures are followed, injury could result. Ask an authorized Mazda Dealer how to safely dispose of the pretensioner system or how to scrap a front pretensioner-equipped vehicle.
Page 97 Seating and Safety Restraints Rear seat lap belts Adjusting the center lap belt The lap belt does not adjust automatically. WARNING: The lap belts should fit snugly and as low as possible around the hips, not around the waist. Failure to position the lap belt correctly may cause serious injury in an accident.
Page 98 Seating and Safety Restraints Conditions of operation If... The driver’s safety belt is not buckled before the ignition switch is turned to the ON position... The driver’s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding... The driver’s safety belt is buckled before the ignition switch is turned to the ON...
Page 99 NOTE: If unsure about the proper procedures, bring your vehicle to an authorized Mazda dealership for inspection. Inspect the safety belts to make sure there are no nicks, tears or cuts, replacing if necessary. Check Consider...
Page 100: Air Bags
Mazda recommends that all safety belt assemblies used in vehicles involved in a collision be replaced. However, if the collision was minor and an authorized Mazda technician finds that the belts do not show damage and continue to operate properly, they do not need to be replaced.
Page 101 Seating and Safety Restraints Important supplemental restraint system (SRS) precautions The supplemental restraint system is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. WARNING: Air bags DO NOT inflate slowly or gently and the risk of injury from a deploying air bag is greatest close to the...
Page 102 Do not modify the front end of the vehicle. WARNING: Additional equipment may effect the performance of the air bag sensors increasing the risk of injury. Consult your authorized Mazda dealership before installation of additional equipment. Children and air bags For additional important safety information, read all information on safety restraints in this guide.
Page 103 Seating and Safety Restraints WARNING: Air bags can kill or injure a child in a child seat NEVER place a rear-facing child seat in front of an active air bag. If you must use a forward-facing child seat in the front seat, move the seat all the way back.
Page 104 Seating and Safety Restraints hearing loss. Because air bags must inflate rapidly and with considerable force, there is the risk of death or serious injuries such as fractures, facial and eye injuries or internal injuries, particularly to occupants who are not properly restrained or are otherwise out of position at the time of air bag deployment.
Page 105 WARNING: Disposing of an air bag can be dangerous. Unless all safety procedures are followed, injury can result. Ask an Authorized Mazda Dealer how to safely dispose of an air bag or how to scrap an air bag equipped vehicle.
Page 106 Seating and Safety Restraints WARNING: Side Air Bag Storage Areas: Attaching things to the seat in such a way as to cover the outboard side of the seat in any way is dangerous. In an accident the object could interfere with the side air bag, which inflates from the outboard side of the front seats, impeding the added protection of the side air bag system or redirecting the air bag in a way that is dangerous.
Page 107 WARNING: Disposing of an air bag can be dangerous. Unless all safety procedures are followed, injury can result. Ask an Authorized Mazda Dealer how to safely dispose of an air bag or how to scrap an air bag equipped vehicle.
Page 108 Seating and Safety Restraints How does the side air bag system work? The side air bag system (if equipped) consists of the following: An inflatable nylon bag (air bag) with a gas generator concealed behind the outboard bolster of the driver and front passenger seatbacks.
Page 109 WARNING: Disposing of an air bag can be dangerous. Unless all safety procedures are followed, injury can result. Ask an Authorized Mazda Dealer how to safely dispose of an air bag or how to scrap an air bag equipped vehicle.
Page 110: Safety Restraints For Children
Seating and Safety Restraints SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safety restraints for children. Also see Air bag supplemental restraint system (SRS) in this chapter for special instructions about using air bags. Important child restraint precautions NOTE: You are required to use safety restraints for children in the U.S.
Page 111 To improve the fit of both the lap and shoulder belt on children who have outgrown child safety seats, Mazda recommends use of a belt-positioning booster seat. Booster seats position a child so that safety belts fit better. They lift the child up so that the lap belt rests low across the hips and the knees bend comfortably.
Page 112 Seating and Safety Restraints Is the shoulder belt centered on the shoulder and chest? Can the child stay seated like this for the whole trip? WARNING: Booster seats must be installed only in seating positions equipped with a combination lap/shoulder belt. Types of booster seats There are two types of belt-positioning booster seats: Those that are backless.
Page 113: Safety Seats For Children
Seating and Safety Restraints The importance of shoulder belts Using a booster without a shoulder belt increases the risk of a child’s head hitting a hard surface in a collision. For this reason, you should never use a booster seat with a lap belt only. It is best to use a booster seat with lap/shoulder belts in the back seat- the safest place for children to ride.
Page 114 Put the safety belt in the automatic locking mode. Refer to Automatic locking mode (passenger side front seat). Mazda recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage.
Page 115 Seating and Safety Restraints 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together. 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions.
Page 116 Seating and Safety Restraints 5. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode.
Page 117 Seating and Safety Restraints Check to make sure the child seat is properly secured before each use. Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap which goes over the back of the seat and hooks to an anchoring point. Tether straps are available as an accessory for many older safety seats.
Page 118 Seating and Safety Restraints 3. Locate the correct anchor for the selected seating position. NOTE: There are three tether anchors located on the headliner at the rear of the vehicle. WARNING: If the tether strap is clipped incorrectly, the child safety seat may not be retained properly in the event of a collision.
Page 119 Seating and Safety Restraints Attaching safety seats with LATCH (Lower Anchors and Tethers for Children) attachments for child seat anchors Some child safety seats have two rigid or webbing mounted attachments that connect to two anchors at certain seating positions in your vehicle. When properly installed, this type of seat eliminates the need to use seat belts to attach the child seat.
Page 120 Seating and Safety Restraints The lower anchors for child seat installation are located at the rear section of the rear seat between the cushion and seat back. The LATCH anchors are below the locator symbols on the seatback. Follow the child seat manufacturer’s instructions to properly install a child seat with LATCH attachments.
Page 121: Driving
Driving STARTING Positions of the ignition 1. LOCK, locks the gearshift lever and allows key removal. 2. ACCESSORY, allows the electrical accessories such as the radio to operate while the engine is not running. 3. ON, all electrical circuits operational. Warning lights illuminated.
Page 122 (RPM). When the engine starts, the idle RPM runs higher than normal in order to warm the engine. If the engine idle speed does not slow down automatically, have the vehicle checked by your authorized Mazda dealership. Before starting the vehicle: 1.
Page 123 If starting a vehicle with a manual transmission: Make sure the parking brake is set. Push the clutch pedal to the floor. 3. Turn the key to 3 (ON) without turning the key to 4 (START). BRAKE CHECK FUEL Make sure the corresponding lights illuminate or illuminate briefly. If a light fails to illuminate, have the vehicle serviced.
Page 124 Take precautions to avoid its dangerous effects. WARNING: If you ever smell exhaust fumes of any kind inside your vehicle, have your authorized Mazda dealer inspect and fix your vehicle immediately. Do not drive if you smell exhaust fumes. These fumes are harmful and result in accident or death.
Page 125: Brakes
If a “metal-to-metal,” “continuous grinding” or “continuous squeal” sound is present while braking, the brake linings may be worn-out and should be inspected by an authorized Mazda dealership. Driving...
Page 126 ABS warning light will come on. If the vehicle has continuous vibration or shudder in the steering wheel while braking, the vehicle should be inspected by an authorized Mazda dealership. The ABS operates by detecting the...
Page 127 (If your brake warning lamp illuminates, have your vehicle serviced immediately by an authorized Mazda dealership.) Using four wheel ABS (if equipped) In an emergency or when maximum efficiency from the ABS is required, apply continuous force on the brake.
Page 128 Driving WARNING: Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park) (automatic transmission) or in 1 (First Gear) (manual transmission). NOTE: The parking brake is not recommended to stop a moving vehicle. However, if the normal brakes fail, the parking brake can be used to stop your vehicle in an emergency.
Page 129: Preparing To Drive Your Vehicle
PREPARING TO DRIVE YOUR VEHICLE Your vehicle has special design and equipment features to make it capable of performing in a wide variety of circumstances. These special design features, such as larger tires and increased ground clearance, give the vehicle a higher center of gravity than a passenger car. WARNING: Utility vehicles have a significantly higher rollover rate than other types of vehicles.
Page 130 Driving If you cannot move the gearshift lever out of P (Park) with ignition in the ON position and the brake pedal depressed: 1. Apply the parking brake, turn ignition key to LOCK, then remove the key. 2. Locate the access cover plate to the brake-shift interlock override.
Page 131 WARNING: If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly. See your authorized Mazda dealership. Driving with an automatic overdrive transaxle Your automatic transaxle electronically controls the shift feel by using an adaptive learning strategy.
Page 132 Driving Understanding gearshift positions P (Park) Always come to a complete stop before shifting into P (Park). Make sure the gearshift lever is securely latched in P (Park). This locks the transaxle and prevents the front wheels from rotating. WARNING: Always set the parking brake fully and make sure the gearshift is latched in P (Park).
Page 133 O/D OFF control is pressed, there may be a transaxle electronic system malfunction. You should contact your authorized Mazda dealer as soon as possible or damage to the transaxle could occur.
Page 134 O/D OFF control is pressed, there may be a transaxle electronic system malfunction. You should contact your authorized Mazda dealer as soon as possible or damage to the transaxle could occur.
Page 135: Manual Transaxle Operation (If Equipped)
Do not rock the vehicle if the engine is not at normal operating temperature or damage to the transmission may occur. Do not rock the vehicle for more than a minute or damage to the transmission and tires may occur, or the engine may overheat. MANUAL TRANSAXLE OPERATION (IF EQUIPPED) Using the clutch Vehicles equipped with a manual transaxle have a starter interrupt...
Page 136 Driving 4. Without depressing the accelerator pedal, turn the ignition to position 4 (START), release the ignition as soon as the engine starts. 5. Let the engine idle for a few seconds. 6. Release the brake pedal, then slowly release the clutch pedal while pressing down slowly on the accelerator pedal.
Page 137 Put the gearshift lever into the neutral position and wait at least three seconds before shifting into R (Reverse). NOTE: You can shift into R (Reverse) only by moving the gearshift lever from left of 3 (Third) and 4 (Fourth) gears before you shift into R (Reverse).
Page 138 Driving 3. Shift into 1 (First). 4. Turn the ignition to position 1 (LOCK) to shut the engine off and remove the ignition key. WARNING: Do not park your vehicle in Neutral, it may move unexpectedly and injure someone. Use 1 (First) gear and set the parking brake fully.
Page 139 4x4 system indicator lights The 4x4 mode indicator light illuminates only under the following conditions. If the indicator light illuminates when driving in the 4x4 AUTO mode, contact your Mazda dealer as soon as possible. Driving LOCK LOCK...
Page 140 Driving The indicator light illuminates when the 4x4 ON mode is engaged. Shifting between 4x4 Auto and ON modes Press the four-wheel drive control to apply power to both axles. When you activate the control, the indicator light will illuminate in the instrument cluster.
Page 141 pavement only after reducing your speed. Do not turn the steering wheel too sharply while returning to the road surface. It may be safer to stay on the apron or shoulder of the road and slow down gradually before returning to the pavement. You may loose control if you do not slow down or if you turn the steering wheel too sharply or abruptly.
Page 142 WARNING: If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly. See your authorized Mazda dealership. Do not rock the vehicle if the engine is not at normal operating temperature or damage to the transaxle may occur.
Page 143 Sand When driving over sand, try to keep all four wheels on the most solid area of the trail. Avoid reducing the tire pressures but shift to a lower gear and drive steadily through the terrain. Apply the accelerator slowly and avoid spinning the wheels.
Page 144 Mazda Motor Corporation joins the U.S. Forest Service and the Bureau of Land Management in encouraging you to help preserve our national forest and other public and private lands by “treading lightly.”...
Page 145 Descend a hill in the same gear you would use to climb up the hill to avoid excessive brake application and brake overheating. Do not descend in neutral; instead, disengage overdrive or manually shift to a lower gear. When descending a steep hill, avoid sudden hard braking as you could lose control.
Page 146 Tires, Replacement Requirements Do not use a size and type of tire and wheel other than that originally provided by Mazda Motor Corporation because it can affect the safety and performance of your vehicle, which could lead to loss of vehicle control or rollover and serious injury.
Page 147: Driving Through Water
The suspension and steering systems on your vehicle have been designed and tested to provide predictable performance whether loaded or empty and durable load carrying capability. For this reason, Mazda Motor Corporation strongly recommends that you do not make modifications...
Page 148: Vehicle Loading
Driving and if the ignition system gets wet, your engine may stall. Water may also enter your engine’s air intake and severely damage your engine. If driving through deep or standing water is unavoidable, proceed very slowly. Never drive through water that is higher than the bottom of the hubs (for trucks) or the bottom of the wheel rims (for cars).
Page 149 GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Label located on the driver’s door or door pillar. The total load on each axle must never exceed its GAWR.
Page 150 Driving WARNING: Exceeding the Safety Certification Label axle weight rating limits could result in substandard vehicle handling, performance, engine, transmission and/or structural damage, serious damage to the vehicle, loss of control and personal injury. GCW (Gross Combined Weight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer.
Page 151: Trailer Towing
WARNING: Do not use replacement tires with lower load carrying capacities than the originals because they may lower the vehicle’s GVWR and GAWR limitations. Replacement tires with a higher limit than the originals do not increase the GVWR and GAWR limitations. WARNING: Exceeding any vehicle weight rating limitation could result in serious damage to the vehicle and/or personal injury.
Page 152 Driving Trailer towing puts additional loads on your vehicle’s engine, transaxle, axle, brakes, tires, and suspension. For your safety and to maximize vehicle performance, be sure to use the proper equipment while towing. Follow these guidelines to ensure safe towing procedure: Be sure to locate all the warnings supplied by the trailer rental or sales company and study the unique requirements of each trailer you intend to tow.
Page 153 Preparing to tow Use the proper equipment for towing a trailer and make sure it is properly attached to your vehicle. See your authorized Mazda dealer. Driving Trailer Weight Maximum Range - kg (lbs.)
Page 154 Trailer lamps are required on most towed vehicles. Make sure all running lights, brake lights, turn signals and hazard lights are working. See your authorized Mazda dealer for proper instructions and equipment for hooking up trailer lamps. Driving while you tow When towing a trailer: Turn off the speed control.
Page 155 Anticipate stops and brake gradually. Do not exceed the GCWR rating or transmission damage may occur. Servicing after towing If you tow a trailer for long distances, your vehicle will require more frequent service intervals. Refer to the “Scheduled Maintenance” section for more information.
Page 156: Recreational Towing
Driving RECREATIONAL TOWING An example of “recreational towing” is towing your vehicle behind a motorhome. If your vehicle is automatic transmission equipped, with a 4x2 (front-wheel drive only) configured powertrain, “recreational towing” is permitted by trailering the vehicle with its front wheels on a dolly. This protects the transmission’s internal mechanical components from potential lack of lubrication damage.
Page 157: Roadside Emergencies
Roadside Emergencies HAZARD FLASHER CONTROL The hazard flasher is located on the instrument panel by the radio. The hazard flashers will operate when the ignition is off. Push in the flasher control and all front and rear direction signals will flash.
Page 158: Fuses And Relays
Roadside Emergencies FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within the fuse. Check the appropriate fuses before replacing any electrical components. Note: Always replace a fuse with one that has the specified amperage rating.
Page 159 To remove a fuse use the fuse puller tool provided on the fuse panel cover. The fuses are coded as follows: Fuse/Relay Fuse Amp Location Rating Roadside Emergencies Passenger Compartment Fuse Panel Description Canister vent control solenoid Blower relay (coil), Pressure switch to PCM Rear wiper motor, Rear washer motor, Rear wiper relay (coil)
Page 160 Roadside Emergencies Fuse/Relay Fuse Amp Location Rating — Passenger Compartment Fuse Panel Description ABS unit (EVAC & FILL), ASC unit, Restraints Control Module (RCM), ASC main SW to ASC unit, Clock spring switch Flasher unit, Reversing lamps, Park Aid Module (PAM) Passive Anti-theft Transceiver (PATS), RCM, EEC fuse Cluster, Shift lock relay (coil),...
Page 161 Fuse/Relay Fuse Amp Location Rating — Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads. WARNING: Always disconnect the battery before servicing high current fuses.
Page 162 Roadside Emergencies WARNING: To reduce risk of electrical shock, always replace the cover to the Power Distribution Box before reconnecting the battery or refilling fluid reservoirs. If the battery has been disconnected and reconnected, refer to the Battery section of the Maintenance and specifications chapter. (ABS) MAIN 120A...
Page 163 Fuse/Relay Fuse Amp Location Rating FUEL 20A* DIODE — DIODE — H/L RELAY — MICRO HTD SEATS 30A** MAIN 120A 15A* (DRL) 15A* 15A*(DRL2) (DRL2) (HLEV) 10A(HLEV) PWR 1 15A* 20A* 15A* (ABS) 25A* PWR 2 15A* IG MAIN 40A** 40A** BTN 1 40A**...
Page 164: Overheating
Roadside Emergencies Fuse/Relay Fuse Amp Location Rating MAIN FAN 40A** (2.0 L) 50A(3.0 L) R DEF 30A** ADD FAN 40A**(2.0 L) 50A(3.0 L) EEC MAIN ISO — FUEL PUMP ISO — MAIN FAN ISO — ADD FAN ISO — DEF RELAY ISO —...
Page 165: Temporary Spare Tire Information
If you find a leak or other damage, or if coolant is still leaking, stop the engine and call an Authorized Mazda dealer. See Adding coolant in the Maintenance and specifications section. If you find no problems, the engine is cool and no leaks are obvious, carefully add coolant as required.
Page 166 Roadside Emergencies WARNING: If you use the temporary spare tire continuously or do not follow these precautions, the tire could fail, causing you to lose control of the vehicle, possibly injuring yourself or others. When driving with the temporary spare tire do not: use more than one temporary spare tire at a time exceed 80 km/h (50 mph) or drive further than 3,200 km (2,000 miles) total under any circumstances...
Page 167 WARNING: Changing a tire is dangerous if not done properly. The vehicle can slip off the jack and seriously injure you or someone. Be sure to follow the directions for changing a tire, and never get under a vehicle that is supported only by a jack. 1.
Page 168 Roadside Emergencies 5. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground. Before placing the jack under the vehicle, NOTE the jack locations: Front jacking notches are located under the front suspension arm.
Page 169 6. Position the jack according to the following guides and turn the jack handle clockwise until the tire is a maximum of 25 mm (1 inch) off the ground. Never use the differentials as a jacking point. It is too easy for the vehicle to tilt or fall and you can be injured.
Page 170 Roadside Emergencies 10. Remove the jack and fully tighten the lug nuts in the order shown. NOTE: To stow the full size flat tire in the cargo floor, the long spare tire rod in the tool bag needs to be installed.
Page 171: Jump Starting
M12 x 1.5 113-153 * Torque specifications are for nut and bolt threads free of dirt and rust. Use only Mazda recommended replacement fasteners. WARNING: When a wheel is installed, always remove any corrosion, dirt or foreign materials present on the mounting surfaces of the wheel or the surface of the front disc brake hub and rotor that contacts the wheel.
Page 172 Roadside Emergencies Preparing your vehicle When the battery is disconnected or a new battery is installed, the transmission must relearn its shift strategy. As a result, the transmission may have firm and/or soft shifts. This operation is considered normal and will not affect function or durability of the transmission.
Page 173 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery. 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery. Roadside Emergencies...
Page 174 Roadside Emergencies 4. Make the final connection of the negative (-) cable to an exposed metal part of the disabled vehicle’s engine, away from the battery and the fuel injection system. NOTE: Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. WARNING: Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped.
Page 175 Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2.
Page 176 Roadside Emergencies 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
Page 177: Wrecker Towing
It is recommended that your vehicle be towed with a wheel lift and dollies or flatbed equipment. Do not tow with a slingbelt. Mazda has not approved a slingbelt towing procedure. If your vehicle is to be towed from the rear using wheel lift equipment, it is recommended that the front wheels (drive wheels) be placed on a dolly to prevent damage to the transaxle.
Page 178 Roadside Emergencies In case of a roadside emergency with a disabled vehicle (without access to wheel dollies, car hauling trailer or flatbed transport vehicle) your vehicle (regardless of powertrain configuration) can be flat towed (all wheels on the ground) under the following conditions: Place the transmission in N (Neutral).
Page 179: Customer Assistance
Mazda vehicle in top condition. If you have any questions or recommendations for improvement regarding the service of your Mazda vehicle or servicing by Mazda Dealer personnel, we recommend that you take the following steps: STEP 1: Contact Your Mazda Dealer Discuss the matter with an Authorized Mazda Dealer.
Page 180: Customer Assistance (Canada)
Customer Assistance If you live outside the U.S.A., please contact your nearest Mazda Distributor. CUSTOMER ASSISTANCE (CANADA) Your complete and permanent satisfaction is our business. We are here to serve you. All Authorized Mazda Dealers have the knowledge and the tools to keep your Mazda vehicle in top condition.
Page 181 Your complete satisfaction is the goal of Mazda Canada Inc. and our dealers. Mazda’s participation in CAMVAP makes a valuable contribution to our achieving that goal.
Page 182: Regional Offices
British Columbia & Yukon Territories Alberta & Northwest Territories Saskatchewan Manitoba Ontario Atlantic Canada Quebec REGIONAL OFFICES Regional Offices Mazda Canada Inc. Western Region 8171 Ackroyd Road Suite 2000 Richmond, B.C. V6X 3K1 (604) 303–5670 Mazda Canada Inc. Central/Atlantic Region 305 Milner Avenue Suite 400 Scarborough, Ontario.
Page 183: Customer Assistance (Puerto Rico)
Authorized Mazda Dealers have the knowledge and the tools to keep your Mazda vehicle in top condition. If you have any questions or recommendations for improvement regarding the service of your Mazda vehicle or servicing by Mazda Dealer personnel, we recommend that you take the following steps: STEP 1 Discuss the matter with an Authorized Mazda Dealer.
Page 184: Puerto Rico
Scarborough, Ontario M1B 3V4 Canada TEL: 1 (800) 263–4680 (in Canada) (416) 609–9909 (outside Canada) PUERTO RICO Plaza Motors Corp. (Mazda de Puerto Rico) P.O. Box 362722, San Juan, Puerto Rico 00936–2722 TEL: (787) 788–9300 GUAM (d.b.a. Triple J. Enterprises, Inc.) P.O.
Page 185: Add-On Non-Genuine Parts And Accessories
TEL: (684) 699–1854 ADD-ON NON-GENUINE PARTS AND ACCESSORIES Non-genuine parts and accessories for Mazda vehicles can be found in stores. These may fit your vehicle, but they are not approved by the manufacturer for use with Mazda vehicles. When you install non-genuine parts or accessories, they could affect your vehicle’s performance or...
Page 186: Outside The United States
NOT take your Mazda outside the United States. However, in the event that you are moving to Canada permanently, Mazda vehicles built for use in the United States could be eligible for exportation to Canada with specific vehicle modifications to comply with the Canadian Motor Vehicle Safety requirements.
Page 187: Reporting Safety Defects
However NHTSA cannot become involved in individual problems between you, your dealer, or your Mazda importer/distributor). To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1 (800) 424–9393 (or 366–0123 in Washington, D.C.
Page 188: Service Publications
Customer Assistance If you live outside of the U.S.A., please contact the nearest Mazda Distributor. (See the Mazda Importers/Distributors section of this manual). SERVICE PUBLICATIONS Factory-authorized Mazda service publications are available for owners who wish to do some of their own maintenance and repair.
Page 189: Reporting Safety Defects (U.s. Only)
However, NHTSA cannot become involved in individual problems between you, your dealer or Mazda Corporation. To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1–800–424–9393 (202–366–0123 in the Washington D.C.
Page 190: Cleaning
Cleaning WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutral Ph shampoo, such as an approved shampoo available from your Mazda dealer. Never use strong household detergents or soap, such as dish washing or laundry liquid. These products can discolor and spot painted surfaces.
Page 191: Paint Chips
Never spray the engine or other engine components with water. Water will damage the engine or other engine components. Spray Engine Shampoo and Degreaser, available at your authorized Mazda dealer, on all parts that require cleaning and pressure rinse clean. Cover the highlighted areas to prevent water damage when cleaning the engine.
Page 192: Plastic (Non-Painted) Exterior Parts
For routine cleaning, use One Step Wash and Wax Concentrate, available at your authorized Mazda dealer. If tar or grease spots are present, use Extra Strength Tar and Road Oil Removal, available at your authorized Mazda dealer.
Page 193: Windows And Wiper Blades
The windshield or rear window may be cleaned with a non-abrasive cleaner such as Ultra Clear Spray Glass Cleaner, available from your authorized Mazda dealer. Do not use abrasives, as they may cause scratches. Do not use fuel, kerosene, or paint thinner to clean any parts.
Page 194: Leather Seats (If Equipped)
Remove light stains and soil with Extra Strength Upholstery Cleaner, available at your authorized Mazda dealer. If grease or tar is present on the material, spot-clean the area first with Spot and Stain Remover, available at your authorized Mazda dealer. Never saturate the seat covers with cleaning solution.
Page 195 Cleaning MAZDA CAR CARE PRODUCTS Your Mazda dealer has many quality products available to clean your vehicle and protect its finishes. These quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle. Each product is made from high quality materials that meet or exceed rigid specifications.
Page 196: Maintenance And Specifications
This could lead to vehicle damage or an accident and injuries. For expert advice and quality service, consult an Authorized Mazda Dealer. The owner should retain evidence that proper maintenance has been performed as prescribed.
Page 197: Ignition System
Maintenance and Specifications SCHEDULE 1 I: Inspect and repair, clean, adjust, or replace if necessary (Oil-permeated air filter cannot be cleaned using the air-blow method) R: Replace L: Lubricate Maintenance Interval (Number of months or km (miles), Months Maintenance Item x 1000 Km (x 1000 Miles) (7.5) (15) (22.5) (30) (37.5) (45) (52.5) (60) (67.5) (75) (82.5) (90) ENGINE...
Page 198 *1 According to state and federal regulations, failure to perform maintenance on these items will not void your emissions warranties. However, Mazda recommends that all maintenance services be performed at the recommended time or mileage (kilometrage) period to ensure long-term reliability.
Page 199 Maintenance and Specifications SCHEDULE 2 I: Inspect and repair, clean, adjust, or replace if necessary (Oil-permeated air filter cannot be cleaned using the air-blow method) R: Replace L: Lubricate Maintenance Interval (Number of months or km (miles), Months Maintenance Item x 1000 Km (x 1000 Miles) (5) (10) (15) (20) (25) (30) (35) (40) (45) (50) (55) (60) ENGINE...
Page 200: Electrical System
*1 According to state and federal regulations, failure to perform maintenance on these items will not void your emissions warranties. However, Mazda recommends that all maintenance services be performed whichever comes first) Replace at first 160,000 km (100,000 miles) or 60 months;...
Page 201: Owner Maintenance Schedule
The owner or a qualified service technician should make these vehicle inspections at the indicated intervals to ensure safe and dependable operation. Bring any problem to the attention of an Authorized Mazda Dealer or qualified service technician as soon as possible. When Refueling...
Page 202: Precautions When Servicing Your Vehicle
Maintenance and Specifications PRECAUTIONS WHEN SERVICING YOUR VEHICLE WARNING: A hot engine is dangerous. If the engine has been running, parts of the engine compartment can become very hot. You could be burned. Don’t inspect the coolant system or add coolant when the engine is hot.
Page 203: Opening The Hood
Maintenance and Specifications OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom of the instrument panel. 2. At the front of the vehicle, lift up on the auxiliary latch handle located in the center between the hood and the grille. 3.
Page 204: Engine Compartment
Maintenance and Specifications IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 2.0L DOHC I4 Zetec engine 1. Power steering fluid reservoir 2. Engine coolant reservoir 3. Brake/Clutch fluid reservoir 4. Air filter assembly 5. Power distribution box 6. Battery 7. Engine oil filler cap 8.
Page 205 Maintenance and Specifications 3.0L DOHC V6 Duratec engine 1. Power steering fluid reservoir 2. Engine coolant reservoir 3. Automatic transmission fluid dipstick 4. Brake fluid reservoir 5. Air filter assembly 6. Power distribution box 7. Battery 8. Engine oil dipstick 9.
Page 206: Windshield Washer Fluid
Add fluid to fill the reservoir if the level is low. In very cold weather, do not fill the reservoir completely. Only use a washer fluid that meets Mazda specifications. Refer to Refill capacities in this chapter. WARNING: If you operate your vehicle in temperatures below 4.5°...
Page 207 Maintenance and Specifications 3. Set the parking brake and ensure the gearshift is securely latched in P (Park) (automatic transmissions) or 1 (First) (manual transmissions). 4. Open the hood. Protect yourself from engine heat. 5. Locate and carefully remove the engine oil level indicator (dipstick). 2.0L DOHC I4 Zetec engine 3.0L DOHC V6 Duratec engine FULL...
Page 208 Maintenance and Specifications 6. Wipe the indicator clean. Insert the indicator fully, then remove it again. If the oil level is between the MIN-MAX or ADD-FULL marks, the oil level is acceptable. DO NOT ADD OIL. If the oil level is below the MIN or ADD mark, add enough oil to raise the level within the MIN–MAX or ADD-FULL range.
Page 209 If a replacement oil filter is used that does not meet Mazda material and design specifications, start-up engine noises or knock may be experienced. It is recommended you use the appropriate Genuine Mazda oil filter (or another brand meeting Mazda specifications) for your engine application.
Page 210: Battery
Maintenance and Specifications BATTERY Your vehicle is equipped with a Mazda maintenance-free battery which normally does not require additional water during its life of service. However, for severe usage or in high temperature climates, check the battery electrolyte level. Refer to the service maintenance section for the service interval schedules.
Page 211 Maintenance and Specifications WARNING: When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery. Lift the battery with a battery carrier or with your hands on opposite corners.
Page 212: Engine Coolant
Maintenance and Specifications transmission may shift firmly. This operation is considered normal and will not affect function or durability of the transmission. Over time the adaptive learning process will fully update transmission operation to its optimum shift feel. If the battery has been disconnected or a new battery has been installed, the clock and the preset radio stations must be reset once the battery is reconnected.
Page 213 Maintenance and Specifications When the engine is cold, check the level of the engine coolant in the reservoir. The engine coolant should be at the “cold fill level” or within the “cold fill range” as listed on the engine coolant reservoir (depending upon application).
Page 214 Maintenance and Specifications The cooling system in your vehicle is filled with yellow-colored Mazda Premium Engine Coolant meeting Mazda Specifications. To maintain the integrity of the coolant and the cooling system and maintain the warranty on the cooling system: Add Mazda Premium Engine Coolant.
Page 215 Not all coolant recycling processes produce coolant which meets Mazda recommend coolants. Use of a recycled engine coolant which does not meet the Mazda recommended coolant, may harm engine and cooling system components. Always dispose of used automotive fluids in a responsible manner.
Page 216 Maintenance and Specifications Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, refer to Refill capacities in this chapter. Fill your engine coolant reservoir as outlined in Adding engine coolant in this chapter. Severe climates If you drive in extremely cold climates (less than –36°...
Page 217: What You Should Know About Automotive Fuels
Maintenance and Specifications WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions WARNING: Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire. WARNING: The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap.
Page 218 Maintenance and Specifications WARNING: Automotive fuels can be harmful or fatal if swallowed. Fuel such as gasoline is highly toxic and if swallowed can cause death or permanent injury. If fuel is swallowed, call a physician immediately, even if no symptoms are immediately apparent.
Page 219 Maintenance and Specifications WARNING: When refueling always shut the engine off and never allow sparks or open flames near the filler neck. Never smoke while refueling. Fuel vapor is extremely hazardous under certain conditions. Care should be taken to avoid inhaling excess fumes.
Page 220 Ask your fuel supplier about gasolines that meet the World-wide Fuel Charter. Cleaner air Mazda endorses the use of reformulated “cleaner-burning” gasolines to improve air quality. Running out of fuel Avoid running out of fuel because this situation may have an adverse affect on powertrain components.
Page 221 Fuel Filter For fuel filter replacement, see your authorized Mazda dealership. Refer to the service maintenance section for the appropriate intervals for changing the fuel filter.
Page 222: Essentials Of Good Fuel Economy
Maintenance and Specifications ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Your best source of information about actual fuel economy is you, the driver. You must gather information as accurately and consistently as possible. Fuel expense, frequency of fillups or fuel gauge readings are NOT accurate as a measure of fuel economy.
Page 223 Maintenance and Specifications 2. Each time you fill the tank, record the amount of fuel added (in liters or gallons). 3. After at least three to five tank fill-ups, fill the fuel tank and record the current odometer reading. 4. Subtract your initial odometer reading from the current odometer reading.
Page 224 Maintenance and Specifications Warming up a vehicle on cold mornings is not required and may reduce fuel economy. Resting your foot on the brake pedal while driving may reduce fuel economy. Combine errands and minimize stop-and-go driving. Maintenance Keep tires properly inflated and use only recommended size. Operating a vehicle with the wheels out of alignment will reduce fuel economy.
Page 225: Emission Control System
If other than Mazda authorized parts are used for maintenance replacements or for service of components affecting emission control, such non-Mazda parts should be equivalent to genuine Mazda parts in performance and durability. WARNING: Do not park, idle, or drive your vehicle in dry grass or other dry ground cover.
Page 226 Maintenance and Specifications Do not make any unauthorized changes to your vehicle or engine. By law, vehicle owners and anyone who manufactures, repairs, services, sells, leases, trades vehicles, or supervises a fleet of vehicles are not permitted to intentionally remove an emission control device or prevent it from working.
Page 227: Checking And Adding Power Steering Fluid
Maintenance and Specifications CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid. Refer to the service maintenance section for the service interval schedules. If adding fluid is necessary, use only MERCON ATF. 1. Start the engine and let it run until it reaches normal operating temperature (the engine coolant temperature gauge indicator will be near the center of the normal area between H and C).
Page 228: Transmission Fluid
If the fluid levels are outside of the normal operating range, the performance of your brake/clutch (if equipped) system could be compromised, seek service from an authorized Mazda dealer immediately. TRANSMISSION FLUID Checking automatic transmission fluid Refer to your scheduled maintenance section for scheduled intervals for fluid checks and changes.
Page 229 Maintenance and Specifications Low fluid level Do not drive the vehicle if the fluid level is at the bottom of the dipstick and the outside temperatures are above 10°C (50°F). Correct fluid level The transmission fluid should be checked at normal operating temperatures 66°C-77°C (150°F-170°F) on a level surface.
Page 230: Clutch Fluid (Manual Transaxle)
4. Add enough fluid through the filler opening so that the fluid level is at the bottom of the opening. 5. Install and tighten the fill plug securely. Use only fluid that meets Mazda specifications. Refer to the Refill capacities in this chapter. CLUTCH FLUID (MANUAL TRANSAXLE)
Page 231: Air Filter(S)
Refer to the service maintenance section for the appropriate intervals for changing the air filter element. When changing the air filter element, only use a Genuine Mazda air filter element. WARNING: Don’t drive without an air filter. This could result in excessive engine wear.
Page 232: Information About Uniform Tire Quality Grading
10 to 12 inches or limited production tires as defined in Title 49 Code of Federal Regulations Part 575.104(c)(2). U.S. Department of Transportation-Tire quality grades: The U.S. Department of Transportation requires Mazda to give you the following information about tire grades exactly as the government has written it. Treadwear...
Page 233 Maintenance and Specifications Temperature A B C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
Page 234: Information Contained On The Tire Sidewall
Maintenance and Specifications PSI: Pounds per square inch, a standard unit of air pressure. B-pillar: The structural member at the side of the vehicle behind the front door. Bead area of the tire: Area of the tire next to the rim. Sidewall of the tire: Area between the bead area and the tread.
Page 235 Maintenance and Specifications 4. R: Indicates a “radial” type tire. 5. 15: Indicates the wheel or rim diameter in inches. If you change your wheel size, you will have to purchase new tires to match the new wheel diameter. 6. 95: Indicates the tire’s load index. It is an index that relates to how much weight a tire can carry.
Page 236 Maintenance and Specifications four numbers represent the week and year the tire was built. For example, the numbers 317 mean the 31st week of 1997. After 2000 the numbers go to four digits. For example, 2501 means the 25th week of 2001. The numbers in between are marketing codes used at the manufacturer’s discretion.
Page 237 Maintenance and Specifications Note: You may not find this information on all tires because it is not required by federal law. The tire suppliers may have additional markings, notes or warnings such as standard load, radial tubeless, etc. Additional information contained on the tire sidewall for “LT” type tires “LT”...
Page 238: Tire Care
You are strongly urged to buy a reliable tire pressure gauge, as automatic service station gauges may be inaccurate. Mazda recommends the use of a digital or dial type tire pressure gauge rather that a stick type tire pressure gauge.
Page 239 Maintenance and Specifications Use the recommended cold inflation pressure for optimum tire performance and wear. Under-inflation or over-inflation may cause uneven treadwear patterns. NOTE: If you are driving the vehicle at its maximum weight load, make sure the tire inflation pressure is correct for the weight load on the tires. WARNING: Under-inflation is the most common cause of tire failures and may result in severe tire cracking, tread separation or blowout , with unexpected loss of vehicle control and...
Page 240 If your vehicle seems to pull to one side, vibrate or shake when you’re driving, the wheels may be out of alignment. Have a qualified technician at a Mazda dealer check the wheel alignment periodically.
Page 241 Maintenance and Specifications Front Wheel Drive (FWD) vehicles (front tires at top of diagram) Rear Wheel Drive (RWD) vehicles/Four Wheel Drive (4WD) vehicles (front tires at top of diagram)
Page 242 Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask a qualified technician at a Mazda dealership to check for and correct any wheel misalignment, tire imbalance or mechanical problem involved before tire rotation.
Page 243: Using Snow Tires And Traction Devices
Maintenance and Specifications Safety practices Driving habits have a great deal to do with your tire mileage and safety. Observe posted speed limits Avoid fast starts, stops and turns Avoid potholes and objects on the road Do not run over curbs or hit the tire against a curb when parking If you vehicle is stuck in snow, mud, sand, etc., do not rapidly spin the tires;...
Page 244: Refill Capacities
Maintenance and Specifications Follow these guidelines when using snow tires and traction devices: SAE class “S” cables should be used on front axle for P235/70R16 tires. With P215/70R16 tires, SAE class “S” cables can be used on both the front and rear wheels. Do not use tire chains on aluminum wheels.
Page 245 API service fluid GL-4, SAE 75W-90 MERCON ATF Transfer Case SAE 75W-140 Synthetic Lubricant API service GL-5, SAE 80W-90 Engine coolant Mazda yellow-colored Premium Engine Coolant Rear axle API service lubricant GL-5, SAE 80W-90 Premium Rear Axle Lubricant Windshield washer fluid Ensure the correct automatic transmission fluid is used.
Page 246: Wheel And Tire Sizes
Coolant (orange in color). Refer to Adding engine coolant in this chapter. Fill to 6 mm to 14 mm (1/4 inch to 9/16 inch) below bottom of fill hole. For further information on your lubrication specifications, see your authorized Mazda dealer. WHEEL AND TIRE SIZES Vehicle Wheel...
Page 247: Vehicle Dimensions
Maintenance and Specifications VEHICLE DIMENSIONS Dimensions (1) Vehicle height/ Maximum height* (2) Front track / rear (3)Overall width (body) (4) Wheelbase (5)Overall length * Denotes a 4x4 vehicle with optional 16” tires 4 Door mm (in.) 1,681 (66.2)/1,744 (68.7)* 1,550 (61.0)/1,530 (60.2) 1,783 (70.2) 2,620 (103.1) 4,394 (173.0)
Page 248: Identifying Your Vehicle
Maintenance and Specifications IDENTIFYING YOUR VEHICLE Certification label The National Highway Traffic Safety Administration Regulations require that a Certification Label be affixed to a vehicle and prescribe where the Certification Label may be located. The Certification Label is located on the front door latch pillar on the driver’s side.
Page 249 Maintenance and Specifications Vehicle identification number (VIN) The vehicle identification number is attached to a metal tag and is located on the driver side XXXXXXXXXXXXXXXXX instrument panel. (Please note that in the graphic XXXX is representative of your vehicle identification number.) Engine number The engine number (the last eight numbers of the vehicle identification number) is stamped on the engine block, transmission, frame and...
Page 250: Accessories
Accessories Accessories CELL PHONES Use of cell phones and other devices by driver: WARNING: Use of any electrical devices such as cell phones, computers, portable radios, vehicle navigation or other devices by the driver while the vehicle is moving is dangerous. Dialing a number on a cell phone while driving also ties-up the driver’s hands.
Page 251: Index
Index ABS (see Brakes) ...126 Accessory delay ...62 Air bag supplemental restraint system ...100–101, 105 and child safety seats ...102 description ...101, 105 disposal ...105, 109 driver air bag ...103, 108 indicator light ...104, 109 operation ...103, 108 passenger air bag ...103, 108 side air bag ...105 Air cleaner filter ...231 Air conditioning...
Page 252 Index Cleaning your vehicle engine compartment ...191 instrument panel ...193 interior ...194 interior trim ...193 Mazda car care products ...195 plastic parts ...192 washing ...190 waxing ...190 wheels ...191 wiper blades ...193 Climate control (see Air conditioning or Heating) ...44 Clock ...26, 39...
Page 253 driving off road ...140 indicator light ...139 preparing to drive your vehicle ...129 Fuel ...217 calculating fuel economy ...222 cap ...220 capacity ...244 choosing the right fuel ...219 comparisons with EPA fuel economy estimates ...224 detergent in fuel ...220 filling your vehicle with fuel ...217, 220, 222 filter, specifications ...221 fuel filler door release ...66...
Page 254 Index Keys positions of the ignition ...121 Lamps bulb replacement specifications chart ...51 cargo lamps ...49 daytime running light ...48 fog lamps ...48 headlamps ...48 headlamps, flash to pass ...49 instrument panel, dimming ...49 interior lamps ...50–51 replacing bulbs ...51–52, 54–55 Lane change indicator (see Turn signal) ...50 Liftgate ...68...
Page 255 Radio reception ...42–43 Rear window defroster ...47 Relays ...158 Remote entry system arming and disarming the anti-theft system ...73 illuminated entry ...74 locking/unlocking doors ...70 replacing the batteries ...73 Roof rack ...69 Safety Belt Maintenance ...99 Safety belts (see Safety restraints) ...90–95 Safety defects, reporting ...189 Safety restraints ...90–95 extension assembly ...96...
Page 256 Index fluid, refill capacities ...244 Turn signal ...50 Vehicle dimensions ...247 Vehicle Identification Number (VIN) ...249 Vehicle loading ...148 Ventilating your vehicle ...125 Warning lights (see Lights) ...10 Washer fluid ...206 Water, Driving through ...147 Windows power ...61 rear wiper/washer ...57 Windshield washer fluid and wipers checking and adding fluid ...206...

This manual is also suitable for:

Tribute om 2004 2004

Mazda 2004 Tribute Owner's Manual

Introduction

Instrument Cluster

Entertainment Systems

Climate Controls

Lights

Driver Controls

Locks and Security

Seating and Safety Restraints

Driving

Roadside Emergencies

Customer Assistance

Cleaning

Maintenance and Specifications

Accessories

Index

Quick Links

Table of Contents

Need help?

Questions and answers

Related Manuals for Mazda 2004 Tribute

Summary of Contents for Mazda 2004 Tribute

This manual is also suitable for:

Table of Contents