Renaming Snapshots; Nulling" The Faders And Panpots; Direct Recall - Tascam TM-D1000 Operation Manual

10 - Snapshots

10.3Renaming snapshots

1
Press the ESCAPE/RECALL
current snapshot name and number is shown
on the top of the display, and the word
RECALL
? is shown on the bottom.
2
Push the
DATA ENTRY
RENAME
tom line reads
S - 0 0 1 K o t o Q u a r t e t
3
Turn the
DATA ENTRY
shot that you want to rename is shown on the
top line of the display.
4
Confirm this with the
5
Rename the snapshot, following the proce-
dures described above, and press
when you are finished.
10.4"Nulling" the faders and
panpots
The term "nulling" the faders and panpots refers to
the way in which the faders and panpots are adjusted
so that their physical positions correspond to the
positions which have been saved in a snapshot mem-
ory or adjusted through external MIDI control.
When a snapshot memory is recalled, it is almost cer-
tain that the physical control settings will differ, and
to make adjustments using the snapshot as a starting
point, it may be necessary to adjust the faders and
panpots accordingly.
Operating Tip
When the physical controls are used to
change the settings from those memorized in
the recalled snapshot, an asterisk appears by
the number of the snapshot on the display:
S N A P S H O T * 0 1 2
B r a n d e n b u r g
To return the controls to the snapshot values:
27
TASCAM TM-D1000 Operations Manual
key until the
knob so that the bot-
:
Ã
R E N A M E ?
knob until the snap-
ENTER key.
ENTER
5
1
Press and hold down the
press the ENTER key:
É É É ∏ ∏ ∑ ∑ É É É É É
É û Â Â Â É É û û û û
The numbers printed around the display (white
on black) show which controls and channels cor-
respond to the on-screen symbols.
The top line of the display shows the positions of
the panpots of the sixteen input channels, as well
as the positions of the level controls of the
EFFECT RETURN and AUX RETURN
controls.
The bottom line of the display shows the position
of the sixteen input channel faders, as well as the
four GROUP/AUX faders and the L-R stereo
faders.
2
The symbols indicate the direction in which
the fader should be moved (
or the rotary control should be turned (
∑
clockwise or counterclockwise). When the
physical control matches the electronic "vir-
tual" control, the symbol will change to a
symbol.
3
If you want to see numerical values for the
channel whose controls you are adjusting,
press the CH SEL key for that channel:
C h : 3 P a n
F a d e r
The physical control values are given in square
brackets. The pan controls can be set from L50
to R50. The center position is indicated by
CTR. Fader values may be set from
100.
To exit the "nulling" mode, enter any of the snapshot
or effect recall or store screens, the location memory
screens, or any of the option menus.

10.5DIRECT RECALL

Direct recall allows you to recall the first 16 user
snapshots, using the
ESCAPE/RECALL
CH SEL keys. The CH SEL
ESCAPE/RECALL key recalls snapshot 001, etc.
The first (initial setting) snapshot 000 cannot be
recalled in this way.
key, and
SHIFT
É É É É ∏ ∑
û Â Â É É É É û û Â
û Â
up or down)
∏
É
L 4 0 [ L 5 0 ]
2 8 [ 3 1 ]
0
to
key with the
key of channel 1 with the