Tascam TM-D1000 Operational Manaual

Initializing TM-D1000 internal data
Hold and press the PARAM SEL and ENTER
press ENTER after selecting All , Snapshot
Setting the word clock
Option System Master Clock Select
tion" on page 16).
Selecting record or mixdown mode
Option MODE MODE select
page 11).
Selecting Buss Function (group/aux allocations)
Option MODE BUSS Function select
on page 11).
Assigning channels to busses
Press the channels's CH SEL key, and then the appropriate
ing channels to busses" on page 18).
Bypassing the group buss system
Press the channel's CH SEL key, and then the
is not assigned to a group buss (see "Using the DIRECT OUTs" on page 19).
Monitoring input channels and tape tracks
Assign the input channels and tape tracks to the stereo L-R buss (see "Monitoring, etc." on
page 21).
Panning channels between output busses
Use the controls above each channel fader.
PAN
Making EQ settings
Press the key until the
PARAM SEL EQ
key. Make sure the key by the
SEL EQ CH ASSIGN
settings using the data editing knobs (see "Equalization" on page 18).
Making stereo linked pairs of channels
Press and hold down the CH SEL key of an odd-numbered channel, and press the
key of the next even-numbered channel (you can also press and hold any even-numbered
key and press odd-numbered key directly before it)—see "Linking channels for simulta-
neous parameter adjustment" on page 20.
Selecting the way in which internal effect units are used
Option Effect Effect Pattern
to match your requirements (see "Selecting effect patterns" on page 24).
Selecting and assigning the AUX and EFFECT RETURN
controls
Option Setup Aux Rtn Input/Assign
the routing of the aux and effect returns.
keys while powering on the TMD-1000, and
or Effect (see page 10).
(see "Word synchroniza-
(see "Choosing REC or MIX mode" on
(see "Buss configurations"
CH ASSIGN key(s) (see "Rout-
DIRECT OUT key, making sure the channel
indicator lights green, and then the channel's
keys is lit, and make the appropriate
CH SEL
— choose an effect pattern which
—choose the source and
Assigning the channels which use dynamic processors
Option Effect
knob to toggle the dynamics on and off, and turn it to move the cursor (see "Assigning
channel dynamics" on page 19).
Setting the dynamic processor parameters
Press the PARAM SEL
CH SEL key of one of the channels using dynamic processors, and use the data editing
knobs to set the processor parameters (see "Assigning channel dynamics" on page 19).
Setting AUX send levels
Press the PARAM SEL
knobs to set the levels (see "Setting aux send levels" on page 24).
Selecting the effect to use
Press the PARAM SEL
DATA ENTRY knob to select the effect type (see "Selecting the effect to use" on page 24).
Editing the effect parameters
After selecting the effect as described above, use the data editing knobs to set the parame-
ters.
Recalling a snapshot
Press the
ESCAPE/RECALL
shot and press
ENTER
Storing a snapshot
Press and hold the
SHIFT
memory, and press
Setting the MMC ID of the TM-D1000
Option MIDI
CH
29).
Controlling an external device though MMC
Press and hold down the
labels below the keys)—see "MIDI Machine control" on page 29.
Selecting the MTC type for location operations
Option MIDI
Storing and locating to location memories
Use the MEMO key (see "Locations" on page 30).
Setting MIDI channels to control the TM-D1000 (Program
Change)
Option MIDI
"Setting Program Change receive channels" on page 32).
Ch Dynamics Insert —push the
key until the EFFECT/DYNAMICS indicator lights green, press the
key until the AUX indicator lights green, and use the data editing
key until the EFFECT/DYNAMICS key lights green, and use the
key until the display shows RECALL?
(see "Recalling snapshots" on page 26).
key and press the
STORE (ESCAPE/RECALL
(see "Storing a snapshot" on page 26).
ENTER
MMC Device ID (see "Setting up the device IDs" on page
key while pressing the MMC control keys (MMC blue
SHIFT
MTC Type (see "Selecting the MTC type" on page 30).
MIDI Ch Select for the Mixer, Effects, Dynamics (see
DATA ENTRY
. Choose the snap-
) key. Choose a