APPLICATIONS
DIMENSIONAL DRAWINGS AND INSTALLATION DATA - -
NEW CONSTRUCTION (CONT.)
Whether you are designing a new structure or
replacing packaged terminal air conditioning units in
WALL SLEEVE MOUNTING DIMENSIONS FOR STANDARD AND ACCESSORY GRILLES
an existing building, Gree GA Series will meet your
needs.
•
Hotels and motels
•
Nursing homes and assisted living care
centers
•
Offices
•
Apartments
•
Single- -family dwellings
•
Home conversions and residential add- -ons
NEW CONSTRUCTION
Standard Polymer Non- -Insulated Wall Sleeve
Standard Polymer Insulated Wall Sleeve
The Gree GA series Packaged Terminal Air
Conditioning (PTAC) unit is designed to meet the
needs of the architect, engineer, and contractor. For
unit installation, Gree's expert support network will
assist in all applicable aspects of the construction
project, from preparing a budget to start-up.
ADVANTAGES FOR NEW
CONSTRUCTION
Design Flexibility for the Architect/Engineer
•
Whisper- -quiet performance, indoors and out
•
No bulky duct system
•
No separate equipment room
•
No water towers or additional cooling
equipment
•
No complex match- -up of different HVAC
components
•
Less sensitivity to building orientation (sun,
wind, shade)
•
Optional architectural grille to permit custom
exterior appearance
Initial Cost Savings for the Building Owner
•
No expensive component HVAC system
purchase
•
No
equipment
engineering staff
•
Two- -part delivery to minimize on- -site
damage
STAMPED OUTDOOR GRILLE
•
Weather- -protected wall sleeve that goes in
Stamped grille thickness 0.75" (9.4)
place during construction; chassis that slides
NOTE: Dimensions in ( ) are in millimeters
in place after construction
•
No seasonal changeover required for cooling
or heating - - units are self- -contained comfort
systems
42"
(1067 mm)
16"
(406 mm)
14-7/8"
(378 mm)
A07633
MAIN STUD
JACK STUD
CRIPPLE
FLOOR
SUB-FLOOR
Framing and Minimum Wall Sleeve Opening
5/8" MIN.
(15.9)
SIDE
room
or
maintenance
1/2" (12.7) MINIMUM
Wall Sleeve Mounting (All Models)
Lower Operating Costs and Reliable Comfort
for The Occupant
•
Heat pump models offer substantial savings
over models with conventional electric
resistance heaters
•
Individual units allow tenants to choose the
degree of comfort and operating economy.
•
Rapid servicing reduces downtime: complete
chassis can be replaced in minutes without
disrupting other occupants.
•
Each unit operates independently of other
units in the building. No dependency by
Amounts in ( ) = mm
building on central HVAC system.
Standard and Extended Metal Insulated Wall
RETROFIT/REPLACEMENT
If you are replacing a unit in an existing wall sleeve,
your options include:
•
JACK STUDS
Replace the existing wall sleeve with the
HEADER - 4" X 4" (101.6 X 101.6) OR
the polymer wall sleeve. See accessory sleeve
(2) 2" X 4" (50.8 X 101.6)
section for selecting the correct sleeve for
your application.
16 1/4"
NOTE: in most cases, when replacing the
(412.8)
42 1/8"
wall sleeve, the exterior grille must also be
(1070.0)
replaced.
•
Use an existing sleeve and exterior grille. The
Gree GA series PTAC will fit into:
The following major competitors' wall
—
sleeves/grilles: Carrier, GE, Amana,
Trane, Friedrich and Bryant, and NO
MEASUREMENTS IN ( ) = mm
A07382
accessory retrofit kit is required.
— Friedrich T series and ZoneAire wall
sleeves, with a required wall sleeve
extension (see accessory Friedrich
Retrofit Wall Sleeve Adapter).
5/8" MIN.
(15.9)
SIDE
1/2" (12.7) MINIMUM
ARCHITECTURAL GRILLE
STANDARD MOUNT
ALUMINUM OR PLASTIC
Architectural grille thickness 1.25" (32)
26
4
42 in
(1067)
16 in
(406)
Available in:
14-3/4 in. (375),
18 in. (457),
24 in. (610),
26 in. (660),
28 in. (711)
Sleeve
A07383A
A07381