FIELD- -INSTALLED ACCESSORIES (CONT.)
APPLICATIONS
OUTDOOR GRILLES
Whether you are designing a new structure or
replacing packaged terminal air conditioning units in
Gree recommends only the use of Gree-supplied
an existing building, Gree GA Series will meet your
grilles for use with the GA series units. However, the
needs.
architectural designs of a building may dictate the use
of special or oversized grilles and/or louvers. Special
•
Hotels and motels
louvers or any special architectural treatment of the
•
Nursing homes and assisted living care
building facade that may restrict free circulation
centers
of condenser airflow should be referred to Gree
•
Offices
Corporation for evaluation and approval.
•
Apartments
•
Aluminum Architectural
Single- -family dwellings
•
Outdoor Grilles (Louvered)
Home conversions and residential add- -ons
Part No.: GRILLE- -ALU- -CLEAR
NEW CONSTRUCTION
Part No.: GRILLE- -ALU- -WHITE
The Gree GA series Packaged Terminal Air
Part No.: GRILLE- -ALU- -BEIGE
Conditioning (PTAC) unit is designed to meet the
Part No.: GRILLE- -ALU- -ALPIN
needs of the architect, engineer, and contractor. For
wall sleeve)
unit installation, Gree's expert support network will
Part No.: GRILLE- -ALU- -BRONZ
assist in all applicable aspects of the construction
Part No.: GRILLE- -ALU- -MBRNZ
project, from preparing a budget to start-up.
Part No.: GRILLE- -ALU- -BROWN
ADVANTAGES FOR NEW
CONSTRUCTION
This premium line of decorative outdoor grilles will
Design Flexibility for the Architect/Engineer
enhance the appearance of any building. The grilles
are made of strong, durable, extruded, anodized
•
Whisper- -quiet performance, indoors and out
aluminum and are designed to be mounted easily from
•
No bulky duct system
inside the room. These elegant grilles, available in
•
No separate equipment room
many standard colors, have baked enamel finishes
•
No water towers or additional cooling
resin, for a superior finish that
containing 50% Kynar
®
equipment
will withstand the most extreme conditions.
•
No complex match- -up of different HVAC
components
•
Less sensitivity to building orientation (sun,
wind, shade)
•
Optional architectural grille to permit custom
exterior appearance
Initial Cost Savings for the Building Owner
•
No expensive component HVAC system
purchase
•
No
equipment
engineering staff
•
Two- -part delivery to minimize on- -site
damage
•
Weather- -protected wall sleeve that goes in
place during construction; chassis that slides
in place after construction
•
No seasonal changeover required for cooling
or heating - - units are self- -contained comfort
systems
(anodized aluminum)
(color matches
room
or
maintenance
Lower Operating Costs and Reliable Comfort
Polymeric Architectural Outdoor Grilles
for The Occupant
(Louvered)
•
Heat pump models offer substantial savings
Part No.: GRILLE- -PLA- -BEIGE
over models with conventional electric
Part No.: GRILLE- -PLA- -ALPIN
resistance heaters
(color matches Gree's polymer wall sleeve)
•
Individual units allow tenants to choose the
This value line of polymeric architectural outdoor
degree of comfort and operating economy.
grilles will blend attractively with most building
•
Rapid servicing reduces downtime: complete
exteriors. Mounted easily from inside the room, the
chassis can be replaced in minutes without
one- -piece, molded grille is designed for protection,
disrupting other occupants.
enhanced appearance, and superior weather-resistance.
•
Each unit operates independently of other
The grille is made of durable polymer and has a
units in the building. No dependency by
colorfast, lightly textured finish that blends well with
building on central HVAC system.
most exterior finishes.
RETROFIT/REPLACEMENT
If you are replacing a unit in an existing wall sleeve,
your options include:
•
Replace the existing wall sleeve with the
the polymer wall sleeve. See accessory sleeve
section for selecting the correct sleeve for
your application.
NOTE: in most cases, when replacing the
wall sleeve, the exterior grille must also be
replaced.
Architectural Grille in
•
Use an existing sleeve and exterior grille. The
Aluminum or Polymeric
Gree GA series PTAC will fit into:
The following major competitors' wall
—
sleeves/grilles: Carrier, GE, Amana,
Standard Outdoor Aluminum Grille
Trane, Friedrich and Bryant, and NO
Part No.: GRILLE- -ALU- -STAMP
accessory retrofit kit is required.
This cost- -effective, one- -piece standard grille is made
— Friedrich T series and ZoneAire wall
from durable anodized aluminum. The grille is
sleeves, with a required wall sleeve
lightweight, has a clear finish, and is easy to install
extension (see accessory Friedrich
from inside the room.
Retrofit Wall Sleeve Adapter).
Standard Grille
18
4