Power Cord For 265V Units - Gree GA Series Product Data

APPLICATIONS
WALL THERMOSTAT INTERFACE
The standard wall thermostat interface provides a
Whether you are designing a new structure or
simple to install thermostat connection. The unit has
replacing packaged terminal air conditioning units in
a removable terminal connector to make field wiring
an existing building, Gree GA Series will meet your
easy. See more info on wall thermostat connections
needs.
in the Dimensional Drawings and Installation Data
•
Section. Hotels and motels
Notes: •
Nursing homes and assisted living care
centers
— Thermostat wire is field supplied and
•
Offices
recommended wire size is 18 to 20 gage
•
solid thermostat wire.
Apartments
•
— Wire should never be routed through the Single- -family dwellings
•
wall sleeve.
Home conversions and residential add- -ons
— It is recommended to include extra wires
NEW CONSTRUCTION
in case a wire breaks or is cut during
installation.
The Gree GA series Packaged Terminal Air
— The thermostat is ordered separately and
Conditioning (PTAC) unit is designed to meet the
a Gree PTAC approved thermostat is
needs of the architect, engineer, and contractor. For
recommended, see the accessory chart in
unit installation, Gree's expert support network will
the back.
assist in all applicable aspects of the construction
project, from preparing a budget to start-up.
EM (ENERGY MANAGEMENT)
INTERFACE ADVANTAGES FOR NEW
CONSTRUCTION
The EM interface is standard and provides a simple to
Design Flexibility for the Architect/Engineer
install, Energy Management connection. The unit has
•
a removable terminal connector to make field wiring
Whisper- -quiet performance, indoors and out
easy. When 24VAC is supplied to the input (the EM •
No bulky duct system
connection), the unit will turn off. Once the 24VAC is
•
No separate equipment room
removed (becomes 0 volts), the unit will turn back
•
No water towers or additional cooling
on.
equipment
Note: For more info, see the section in the back,
•
No complex match- -up of different HVAC
Typical Wiring Schematic
components
Management Interface.
•
Less sensitivity to building orientation (sun,
wind, shade)
•
Optional architectural grille to permit custom

POWER CORD FOR 265V UNITS

exterior appearance
Initial Cost Savings for the Building Owner
The 265v power cord extends 15- -in. (381 mm) from
bottom of front panel and, per UL and National •
No expensive component HVAC system
Electric Codes (NEC), must plug into an electrical
purchase
subbase.
•
No equipment
Note: Accessory power cord and electrical
engineering staff
•
subbase sold separately. (See Accessory section
Two- -part delivery to minimize on- -site
in back of this document.)
damage
•
Weather- -protected wall sleeve that goes in
place during construction; chassis that slides
in place after construction
•
No seasonal changeover required for cooling
or heating - - units are self- -contained comfort
systems
For Energy
room or maintenance
Lower Operating Costs and Reliable Comfort
for The Occupant
•
Heat pump models offer substantial savings
over models with conventional electric
resistance heaters
•
Individual units allow tenants to choose the
degree of comfort and operating economy.
•
Rapid servicing reduces downtime: complete
chassis can be replaced in minutes without
disrupting other occupants.
•
Each unit operates independently of other
units in the building. No dependency by
Terminal Connector Removal and Replacement
building on central HVAC system.
RETROFIT/REPLACEMENT
If you are replacing a unit in an existing wall sleeve,
your options include:
•
Replace the existing wall sleeve with the
the polymer wall sleeve. See accessory sleeve
section for selecting the correct sleeve for
your application.
NOTE: in most cases, when replacing the
wall sleeve, the exterior grille must also be
replaced.
•
Use an existing sleeve and exterior grille. The
Gree GA series PTAC will fit into:
The following major competitors' wall
—
sleeves/grilles: Carrier, GE, Amana,
Trane, Friedrich and Bryant, and NO
Energy Management
accessory retrofit kit is required.
Terminal Connections
— Friedrich T series and ZoneAire wall
sleeves, with a required wall sleeve
Wall Thermostat and Energy Management
extension (see accessory Friedrich
Interface
Retrofit Wall Sleeve Adapter).
265V Power Cord
10
4
R W Y O Gh Gl C
Wall Thermostat
Terminal Connections
A07634
A07635
A07073