Champaign, Il; Kit Inspection - GREAT PLANES Giant U-Can-Do 3D Instruction Manual

Before starting to build, use the Kit Contents list to take an inventory of this kit to make sure it is complete and inspect the parts
to make sure they are of acceptable quality. If any parts are missing or are not of acceptable quality, or if you need assistance
with assembly, contact Great Planes Product Support. When reporting defective or missing parts, use the part names exactly
as they are written in the Kit Contents list on this page.
3
4
6
5
15
(1) Prop Nut Bag (prop nut, spinner, SHCS
and hex wrench)
(8) Heavy Duty Control Horns
(2) Nylon Wing Bolt
(4) Nylon Anti-Rotation Dowels
(1) Tail Wheel Assembly (1-1/4" wheel, 6"
springs, leaf spring, Tail wheel wire, 4 set
screws, steering arm and 3 wheel collars)
(1) Fuel Tank and Hardware
(1) 1/4" x 5/8" [6 x 16mm] Canopy Dowel
(1) Rx and Battery Tray
(1) 3/16" x 3/4" x 4-3/8" [4.8 x 19 x 112mm]
Tank Retainer Stick
(2) Velcro ® Strips (both A and B sides)
(2) Tail Gear Springs (use to steer the tail wheel)
(2) Large Black Control Horn Backplate
(for elevators)
(2) Decal Sheet
(8) 4-40 Threaded Steel Clevis (for aileron,
flap, rudder and elevator controls)
(8) 4-40 Solder-On Clevis (for aileron, flap,
rudder and elevator controls)

KIT INSPECTION

Great Planes Product Support:
3002 N. Apollo Drive, Suite 1
Telephone: (217) 398-8970, ext. 5
E-mail: airsupport@greatplanes.com
2
1
7
10
8
11
9
14
16
Kit Contents (Not Photographed)
(2) 3-16 x 2" [50mm] Axles
(1) Brass Screw-Lock Pushrod Connector
Body (for throttle)
(6) 4-40 Blind Nut (for canopy mounting)
(10) 8-32 Blind Nuts (for stab, main gear and
engine mount)
(2) 5/16-24 Nuts (for axles)
(2) 1/4-20 Blind Nuts
(8) 4-40 Lock Nuts (for clevises)
(4) 4-40 Lock Nuts (for rudder control horns)
(1) 2-56 Nylon Clevis
(1) Nylon Retainer (for throttle)
(2) CA Hinge Strip
(1) 36" [915mm] Gray Pushrod Tube
(installed in the fuse for the antenna)
(1) 12" [305mm] Gray Pushrod Tube
(for throttle)
(17) Silicone Clevis Retainers
(16) 4 x 1/2" [13mm] Screws (for aileron and
flap control horns)
(4) 6-32 Set Screws
(2) #4 x 5/8" [16mm] Screws (for tail gear)

Champaign, IL 61822

Fax: (217) 398-7721
Parts Layout
12
13
5
1. Fuselage
2. Canopy
3. Cowl
4. Fuel Tank
5. Spinner
6. Engine Mount
7. Main Landing Gear (2)
8. Wheels (2)
9. Wheel Pants (2)
10. Wing Tube
11. Horizontal Stabilizer & Elevator
12. Tail Gear Assembly
13. Vertical Fin & Rudder
14. Wing Panels (L&R)
15. Ailerons (L&R)
16. Flaps (L&R)
15
(1) 4-40 x 1/4" [6mm] SHCS (for throttle)
(6) #2 x 1/2" [13mm] screws (for cowl)
(4) 8-32 x 3/4" [19mm] SHCS (for main gear)
(4) 4-40 x 1" [25mm] SHCS (for rudder
control horns)
(10) 4-40 x 3/4" [19mm] SHCS (for elevators
and canopy mounting)
(4) 4-40 x 1/2" [13mm] SHCS (for wheel pants)
(2) 8-32 x 1-1/4" [32mm] SHCS (for stab)
(8) 8-32 x 1" [25mm] SHCS (for engine mount
to the firewall and engine to mount)
(4) 3/16" [4.8mm] Wheel Collars
(1) 2-56 x 17" [430mm] Pushrod
(7) 4-40 x 12" [305mm] Pushrod
(6) #2 Flat Washers (for cowl)
(12) #8 Lock Washers (for engine, engine
mount, landing gear and stab)
(14) #8 Flat Washers (for engine, engine
mount, landing gear and stab)
(6) #4 Flat Washers (for canopy and
wheel pants)
Kit Contents