Table of Contents
Advertisement
Quick Links
Kichler
®
Lighting
7711 East Pleasant Valley Road
P.O. Box 318010
Cleveland, Ohio 44131-8010
Customer Service
866.558.5706
8:30 AM to 5:00 PM EST,
Monday - Friday
Designed to coordinate with a popular Kichler Lighting collection.
Includes our new
CoolTouch
Control System
TM
Looks permanent, but goes wherever you go!
U.S. Patent Pending
Instruction Manual
Chicago
TM
®
™
A Kichler
Décor
ceiling fan
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Kichler Lighting Chicago
Summary of Contents for Kichler Lighting Chicago
- Page 1 Chicago ® ™ A Kichler Décor ceiling fan Designed to coordinate with a popular Kichler Lighting collection. Includes our new CoolTouch Control System Looks permanent, but goes wherever you go! U.S. Patent Pending Kichler ® Lighting 7711 East Pleasant Valley Road P.O.
-
Page 2: Safety Rules
1. SAFETY RULES 1. To reduce the risk of electric shock, insure 8. Avoid placing objects in the path of the electricity has been turned off at the circuit blades. breaker or fuse box before cleaning and maintenace, attempting Installation. 9. -
Page 3: Tools And Materials Required
Chicago 2. TOOLS AND MATERIALS REQUIRED Philips screw driver Slot screw driver 11 mm wrench Step ladder Wire cutters 3. PACKAGE CONTENTS Unpack your fan and check the contents. You should have the following items: Fan blades (5) Mounting bracket (1) -
Page 4: Mounting Options
4. MOUNTING OPTIONS If there isn't an existing UL ( CUL for Canadian Installation) listed mounting box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers. Outlet box Secure the outlet box directly to the building structure. -
Page 5: Hanging The Fan
Chicago 5. HANGING THE FAN REMEMBER to turn off the power. Follow the steps below to hang your fan properly: Screw Step 1. Remove the fan motor and housing shipping block assembly from the protective plastic bag and take the lower styrofoam packing pad out of the carton. - Page 6 Step 6. Slip the coupling cover, canopy Downrod cover and canopy onto the downrod. Rein- Canopy stall hanger ball into the downrod and make Coupling cover sure the cross pin is in place and set screw Canopy cover on hanger ball is tight. Secure the coupling cover is resting on the top of ceiling fan.
-
Page 7: Installation Of Safety Support
Chicago 6. INSTALLATION OF SAFETY SUPPORT Flat Washer Wood Screw Support Brace ( For Canadian Installation ONLY ) Spring Washer Outlet Box A safety support cable is provided to help prevent Ceiling the ceiling fan from failing, please install it as follows. - Page 8 Step 3. Remote Receiver to Outlet Box Electri- Outlex box cal Connections: Connect the black White (neutral) Black (hot) (hot) wire from the ceiling to the black wire marked "AC in L" from the receiver. Connect Green or bare the white(neutral) wire from the ceiling to the Black("AC"...
-
Page 9: Attaching The Fan Blades
Chicago Screw 9. ATTACHING THE FAN BLADES Metal washer Fiber washer Blade Step 1 Attach the blade to the blade bracket using the screws, washers and fiber washers as shown in Figure 16. Start screw into bracket. Repeat for the two remaining screws. -
Page 10: Installing The Switch Housing
11. INSTALLING THE SWITCH HOUSING NOTE: Before continuing, make sure the power is disconnected by turning off the circuit breaker of removing the fuse at the circuit box. Step 1. Loosen the 3 screws on the switch house mounting plate. Step 2. - Page 11 / or light fixture, reinstalling lamps totaling less Metal washer than 190 watts and then turning the power back on. Manual nut Decorative plate YOUR NEW KICHLER CEILING FAN IS NOW READY TO USE. REMEMEBER TO RESTORE Finial Fig. 23 ALL POWER.
- Page 12 14. OPERATING INSTRUCTIONS Restore power to ceiling fan and test for proper operation. , and buttons: These three buttons are used to set the fan speed as follows: = low speed = medium speed = high speed button: This button turns the fan off. The "...
-
Page 13: Installing The Cooltouch™ Control System Wall Plate
Chicago 15. INSTALLING THE CoolTouch™ Ou t l et b o x Sw i t c h CONTROL SYSTEM WALL PLATE Wal l p l at e To install the coolTouch control system wall plate, you can select the following locations to fulfill your wall plate installation. -
Page 14: Troubleshooting
17. TROUBLESHOOTING Problem Solution Fan will not start. 1. Check circuit fuses or breakers. 2. Check line wire connections to the fan and switch wire connections in the switch housing. CAUTION: Make sure main power is off. 3. Check to make sure the dip switches from the transmitter and receiver are set to the same frequency.
Need help?
Do you have a question about the Chicago and is the answer not in the manual?
Questions and answers