Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control. Protect others in the work area from debris such as chips and sparks. Provide barriers or shields as needed. SKU 91935 For technical questions, please call 1-800-444-3353 Page 2...
Remove adjusting keys or wrenches before turning the power tool on. A wrench or a key that is left attached to a rotating part of the power tool may result in personal injury. SKU 91935 For technical questions, please call 1-800-444-3353 Page 3...
Page 4
“Inspection, Maintenance, And Cleaning” section of this manual. Use of unauthorized parts or failure to follow maintenance instructions may create a risk of electric shock or injury. SKU 91935 For technical questions, please call 1-800-444-3353 Page 4...
When the Saw Blade is pinched or bound tightly by the kerf closing down, the Saw Blade stalls and the Motor reaction drives the tool rapidly toward the operator. If the Saw Blade SKU 91935 For technical questions, please call 1-800-444-3353 Page 5...
Page 6
Saw Blade to cut without being forced. When turning off the Saw, allow the Saw Blade to spin down and stop on its own. Do not press against the Saw Blade to stop it. SKU 91935 For technical questions, please call 1-800-444-3353 Page 6...
Page 7
WARNING! People with pacemakers should consult their physician(s) before using this product. Operation of electrical equipment in close proximity to a heart pacemaker could cause interference or failure of the pacemaker. SKU 91935 For technical questions, please call 1-800-444-3353 Page 7...
Your tool must be plugged into an appropriate outlet, properly installed and grounded in accordance with all codes and ordinances. The plug and outlet should look like those in the following illustration. (See Figure A.) FIGURE A SKU 91935 For technical questions, please call 1-800-444-3353 Page 8...
Canadian Standard Association, and the National Electric Code. (See Figure B.) Double insulated tools may be used in either of the 120 volt outlets shown in the following illustration. (See Figure B.) FIGURE B SKU 91935 For technical questions, please call 1-800-444-3353 Page 9...
FEET FEET FEET FEET FEET 0-2.0 2.1-3.4 3.5-5.0 5.1-7.0 7.1-12.0 12.1-16.0 16.1-20.0 *Based on limiting the line voltage drop to five volts at 150% of the rated amperes. FIGURE C SKU 91935 For technical questions, please call 1-800-444-3353 Page 10...
Page 11
Pin Knob (35). Raise and hold the Blade Case (86) of the Miter Saw fully upward. Turn the Lock Pin Knob 90 degrees. Then, insert the Lock Pin (38) into the deep slot in its locked position. (See Figure F, next page.) SKU 91935 For technical questions, please call 1-800-444-3353 Page 11...
Page 12
(See Figures F and G.) BLADE CASE (86) BLADE CASE ARROW SAW BLADE (95) (TEETH POINTING DOWN) SAW BLADE ARROW FIGURE E LOCK PIN KNOB (35) SAFETY COVER (147) “LOCKED UP” POSITION FIGURE F SKU 91935 For technical questions, please call 1-800-444-3353 Page 12...
Page 13
CENTER COVER (142) COVER (147) SPINDLE LOCK (130) FIGURE I FIGURE H Unscrew and remove the Spindle Bolt/Washer (92) . Then, remove the Outer Flange (94). (See Figure J, next page.) SKU 91935 For technical questions, please call 1-800-444-3353 Page 13...
Page 14
Knob 90 degrees. Then, insert the Knob into the shallow slot in its unlocked position. NEVER use the Knob in any cutting operation. SAW BLADE SPINDLE BOLT (95) &WASHER (92) OUTER FLANGE (94) FIGURE K SKU 91935 For technical questions, please call 1-800-444-3353 Page 14...
Page 16
Button or Switch Lever are not operating properly. (See Figure N, next page.) Depress the Safety Button (124) with your thumb, and squeeze the Power Switch (122) which will start the Miter Saw. Then, release the Safety Button. (See Figure N.) SKU 91935 For technical questions, please call 1-800-444-3353 Page 16...
Cord (116) of the Miter Saw is unplugged from its electrical outlet. The depth of cut may be adjusted to a maximum of 2-3/4” at 90°, and 1-1/4” at 45°. SKU 91935 For technical questions, please call 1-800-444-3353 Page 17...
Page 18
Scale located on the Base (16). Then, release pressure on the Lock Lever to lock the Miter Saw in place. (See Figure P.) SKU 91935 For technical questions, please call 1-800-444-3353 Page 18...
(21), Baffle Plate (20), cutting depth, and miter angle and/or bevel angle. Raise the Saw Blade (95) up to allow positioning of the workpiece. Check to make sure the Safety Button (124) and the Power Switch (122) are operating properly. SKU 91935 For technical questions, please call 1-800-444-3353 Page 19...
If abnormal noise or vibration occurs, have the problem corrected before further use. Do not use damaged equipment. Never work with a dull saw blade. SKU 91935 For technical questions, please call 1-800-444-3353 Page 20...
RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. SKU 91935 For technical questions, please call 1-800-444-3353 Page 21...
Pan Head Screw Bushing Screw Brush Holder Cap Screw Brush Holder NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 91935 For technical questions, please call 1-800-444-3353 Page 22...
Page 23
Rivet Compressor Spring Wrench ---------- --------------------------- ------ Dust Bag (Not Shown) NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 91935 For technical questions, please call 1-800-444-3353 Page 23...
ASSEMBLY DIAGRAM NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. REV 04/05 SKU 91935 For technical questions, please call 1-800-444-3353 Page 24...
Page 25
ASSEMBLY DIAGRAM - CONTINUED NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 91935 For technical questions, please call 1-800-444-3353 Page 25...