Page 1
7” PORTABLE WET TILE SAW Model 91511 ASSEMBLY AND OPERATING INSTRUCTIONS Diamond Blade not included; sold separately. Distributed Exclusively by Harbor Freight Tools 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at http://www.harborfreight.com TO PREVENT SERIOUS INjURY, READ AND UNDERSTAND ALL WARNINGS AND INSTRUCTIONS BEFORE USE.
Keep this manual and invoice in a safe and dry place for future reference. GENERAL SAFETY RULES WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS Failure to follow all instructions listed in the following pages may result in electric shock, fire, and/or serious injury. SAVE THESE INSTRUCTIONS SKU 91511 PAGE 2 REV 07j; 09e...
TOOL USE AND CARE Do not force the tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed. SKU 91511 PAGE 3...
Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. If the tools should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user. SKU 91511 PAGE 4...
Page 5
Tools marked with “Grounding Required” have a three wire cord and three prong grounding plug. The plug must be connected to a properly grounded outlet. If the tool should electrically malfunction or break down, grounding provides a low SKU 91511 PAGE 5...
For example, a 14 gauge cord can carry a higher current than a 16 gauge cord. (See Figure B.) When using more than one extension cord to make up the total length, make sure each cord contains at least the minimum wire size required. (See Figure B.) SKU 91511 PAGE 6...
Page 7
* Based on limiting the line voltage drop to five volts at TABLE A 150% of the rated amperes. FIGURE B SYMBOLOGY Double Insulated Canadian Standards Association Underwriters Laboratories, Inc. Volts Alternating Current Amperes No Load Revolutions xxxx/min. FIGURE C Per Minute (RPM) SKU 91511 PAGE 7...
Blade’s washers and nut were specially designed for your Saw, for optimum performance and safety of operation. To avoid accidental injury, always wear heavy duty work gloves and long sleeved work shirt when changing a Saw Blade. SKU 91511 PAGE 8 Rev 07j; 09e...
Page 9
There are certain applications for which this product was designed. It will do the job better and more safely at the rate for which it was intended. Do not modify this product, and do not use this product for a purpose for which it was not intended. SKU 91511 PAGE 9...
(See Figure D.) Once the Blade Lock Nut (27) is removed, remove the Outer Washer (28). (See Figure D.) While wearing heavy duty work gloves to avoid accidental cuts, remove the old SKU 91511 PAGE 10...
Page 11
Guard Support Screw (5). (See Figure D.) Secure the Blade Guard (2) to the top portion of the Guard Support (4), using one Wing Nut Screw (1) and one Wing Nut (3). (See Figure D.) SKU 91511 PAGE 11...
Check Blade Guard for proper upward/downward movement before each use. Do not operate the Wet Tile Saw if the Blade Guard does not move freely. Never clamp or tie the Blade Guard into the upward position. SKU 91511 PAGE 12...
Page 13
(See Figure G.) To Perform Angle Cutting: Make sure the Power Switch (21) is in its “OFF” position. Then, plug the Power Cord (17) into the nearest 120 volt, grounded, electrical outlet. (See Figure H, page 15.) SKU 91511 PAGE 13...
Page 14
Make sure the Power Switch (21) is in its “OFF” position. Then, plug the Power Cord (17) into the nearest 120 volt, grounded, electrical outlet. (See Figure I, next page.) Loosen the Lock Knob on the Miter Guide (24). Then select the degree of cut SKU 91511 PAGE 14...
Page 15
Saw Blade (6) to come to a complete stop on its own. Then remove the workpiece, and unplug the Power Cord (17) from its electrical outlet. (See Figure I.) WORKPIECE (NOT INCLUDED) MITER GUIDE (24) POWER SWITCH (21) FIGURE I SKU 91511 PAGE 15...
UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. SKU 91511 PAGE 16...
Circuit breaker Cover motor Screw Wrench motor bottom base Screw power Cord NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKu 91511 page 17 SKU 91511 PAGE 17...
This warranty gives you specific legal rights and you may also have other rights which vary from state to state. 3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353 SKU 91511 PAGE 18 Rev 09e...