Zone Setup - Russound CAV6.6-S2 System Instruction Manual

INSTALLER
INSTALLATION MENU
Numeric IR (cont'd)
ii. MACRO ID – Enter the macro ID number. Menu advances to SUFFIX CMD (step 9)
e. All Other Selections: Procedure advances to DEVICE CODE (step 7)
7. DEVICE CODE (f) – Source component code for IR control.
8. KEY FUNCTION (f) – Select a function (Disc, etc.).
9. SUFFIX CMD (f) – Tells the system whether a command will be issued after the
selection of the numerical value (e.g., 1, 2 Enter). If "no," proce-
dure advances to SAVE CHANGES (step 13)
10. COMMAND TYPE (f) – Select the type of source command (e.g., CD, TV, etc.).
a. Selected: Learned IR Choose Learned IR if the pre-programmed IR code library does
not support the source component.
i. LEARNED SRC (f) – Select the learned source bank to be assigned to the source
component. Procedure advances to KEY FUNCTION (step 12)
b. Selected: Unassigned The numeric IR Suffix command is cleared. Procedure advances
to SOURCE NUM (step 1)
c. Selected: Default Default selects the same device type and device code previously
setup in BASIC SETUP. Procedure advances to KEY FUNCTION
(step 12)
d. Selected: Macro: (To build macros, see Macro Editor page 57)
i. MACRO - Macro loads a series of commands which are processed when
activated.
ii. MACRO ID – Enter the macro ID number. Menu advances to SAVE CHANGES
(step 13)
e. All Other Selections: Procedure advances to DEVICE CODE (step 11)
11. DEVICE CODE (f) – Source component code for IR control.
12. KEY FUNCTION (f) – Select a function (Enter, Play, etc.).
13. SAVE CHANGES? (f) – Select "yes" to save the changes.
SRC SEL CMD (p)
This procedure permits a command to be sent to the source component when the source component
is initially selected. See Source Setup Menu on Page 48 and Source Select Command & # Of
Sources - Flow Chart on page 63
1. SOURCE NUM (f) – Select the source number this command will be configured for.
52
Source Select Command (cont'd)
2. COMMAND TYPE (f) – Select the type of source command (e.g., CD, TV, etc.).
a. Selected: Learned IR Choose Learned IR if the pre-programmed IR code library does
not support the source component.
i. LEARNED SRC (f) – Select the learned source bank to be assigned to the source
component. Procedure advances to KEY FUNCTION (step 4)
b. Selected: Unassigned The source select command is cleared. Procedure advances to
SAVE CHANGES (step 5)
c. Selected: Default Default selects the same device type and device code previously
setup in BASIC SETUP. Procedure advances to KEY FUNCTION
(step 4)
d. Selected: Macro: (To build macros, see Macro Editor page 57)
i. MACRO - Macro loads a series of commands which are processed when
activated.
ii. MACRO ID – Enter the macro ID number. Menu advances to SAVE CHANGES
(step 5)
e. All Other Selections: Procedure advances to DEVICE CODE (step 3)
3. DEVICE CODE (f) – Source component code for IR control.
4. KEY FUNCTION (f) – Select a function (Play, Enter, etc.).
5. SAVE CHANGES? (f) – Select "yes" to save the changes.
# OF SOURCES (f)
At this field it is necessary to enter the number of sources used in the CAV6.6 system (1 to 6). This
limits the sources displayed on the keypad in the normal running mode when the source button is
pressed, but also limits source selections in the configuration menus. See Source Setup Menu on
Page 48 and Source Select Command & # Of Sources - Flow Chart on page 63
ZONE SETUP (m)
NOTE: This procedure should be performed using the keypad installed in the zone to be configured.
See Installation Menu on Page 48 and Zone Setup - Flow Chart on page 64
Zone Setup allows the installer to adjust properties of the UNO Keypad controlled CAV6.6 zone. This
series of menus allows the system's zones to be configured for these properties:
ZON VOL TRIM SYSON ENABLE PARTY ENABLE
PAGE VOLUME
INSTALLER
INSTALLATION MENU
MASTER ENABL PAGE ENABLE
53