Ernitec Erna Protocol - Siemens Solaris CCDS1415-ST Configuration Manual

Operation
Recall Preset
Store Preset
Run Pattern
Enter OSD Menu Mode
Navigate OSD Menu Mode

12.5.2 Ernitec ERNA protocol

Operation
Pan / Tilt /Zoom / Focus
Iris
AutoIris On
AutoFocus On
AutoFocus Off
Night Mode
Day Mode
One-Touch White Balance
Recall Preset
Start Preset Sequence
Save Preset
Insert Preset into Stack
Delete Preset from Stack
Clear Stack
Sequence Dwell Time
Enter OSD Menu Mode
Navigate OSD Menu Mode
64
Siemens Building Technologies
Fire Safety & Security Products
User action
[n] [PRESET]
[n] hold [PRESET]
[PATTERN]
[9] [5] [PRESET] or [2]
[PRESET] [2] [PRESET] within
2 seconds.
Joystick for
Up/Down/Left/Right.[3]
[PRESET] for Set.
* The presets used to access the OSD are programmable via the XTU.
NOTE
RS485 connection; 2400 baud, no parity, 8 data bits, 1 stop bit.
Camera addressing is 0-254 for cameras 1-255. Also responds to broadcast address 255.
Tested using Ernitec Keyboard 1503M.
User action
Joystick for Pan/Tilt/Zoom,[FN] / [FF]
for Focus
[OPEN] / [CLOSE]
[AUTO] [OPEN] or [AUTO] [CLOSE]
[AUTO] then either [FN] or [FF]
[FN] or [FF]
[4] [AUX ON]
[4] [AUX OFF]
[IC]
[n] [PRESET]
[PRESET SEQUENCE]
[n] [ESC] [PRESET]
[n] [SHIFT]+[INS]
[n][SHIFT]+[DEL]
[ESC] [AUX OFF]
[n] [TIME]
[9] [5] [PRESET] or[2] [PRESET] [2]
[PRESET] within 2 seconds
Joystick for Up/Down/Left/Right.[3]
[PRESET] for Set.
* The presets used to access the OSD are programmable via the XTU.
** It is recommended that the OSD is used to setup a Tour.
Notes
is not set to KEYBOARD.
Range 1-89.Preset 95* or Preset 2* twice within 2 seconds functions
as the OSD Mode 'MENU' command. When in OSD mode Preset 1
switches the joystick between cursor and camera control. When in
OSD cursor mode Preset 3 operates as SET.
Range 1-89.
Recall Preset 95* or Recall Preset 2* twice within 2 seconds
functions as the OSD Mode 'MENU' command.
When in OSD mode Recall Preset 1 switches the joystick between
cursor and camera control. When in OSD cursor mode Recall
Preset 3 operates as SET
Notes
When in OSD cursor mode Pan / Tilt operate as cursor right / left /
up / down (but see also Recall Preset 1 below).
Only operates when exposure priority is set to KEYBOARD.
Overridden automatically on a manual iris operation.
Manual control overrides autofocus.
Activates Auxiliary 4 function. Switches camera to night mode
(colour/mono version only).
Deactivates Auxiliary 4 function. Switches camera to day mode
(colour/mono version only).
If one-touch white balance is enabled in OSD and exposure priority
is not set to KEYBOARD.
Range 1-99. Preset 95* or Preset 2* twice within 2 seconds
functions as the OSD Mode 'MENU' command. When in OSD mode
Preset 1 switches the joystick between cursor and camera control.
When in OSD cursor mode Preset 3 operates as SET.
Starts Tour 1.
Range 1-99.
Appends specified preset to end of current tour if possible**. Speed
= 100%, Dwell = currently selected dwell.
Deletes the last occurrence of the specified preset from the tour** (if
present) and moves the presets above it down by one position.
Leaves any other occurrences of the same preset in the tour intact.
Clears the tour**.
Sets the dwell time used by the next Insert Preset into Stack
command*.
Recall Preset 95* or Recall Preset 2* twice within 2 seconds
functions as the OSD Mode 'MENU' command.
When in OSD mode Recall Preset 1 switches the joystick between
cursor and camera control. When in OSD cursor mode Recall
Preset 3 operates as SET.
08.2006