Vcl Protocol; Videmech Universal Protocol - Siemens Solaris CCDS1415-ST Configuration Manual

12.5.3 VCL protocol

Operation
Pan / Tilt /Zoom / Focus
Iris
AutoIris On
AutoFocus On
AutoFocus Off
Day Mode / Night Mode
One-Touch White Balance
Recall Preset
Start Preset Tour
Save Preset
Enter OSD Menu Mode
Navigate OSD Menu Mode

12.5.4 Videmech Universal protocol

Operation
Pan / Tilt / Zoom / Focus
Iris
AutoFocus On
AutoFocus Off
Night Mode
Day Mode
One-Touch White Balance
Siemens Building Technologies
Fire Safety & Security Products
NOTE
RS485 connection; 9600 baud, no parity, 8 data bits, 2 stop bits.
Camera addressing is 0-127 for cameras 1-128.
Tested using Honeywell HKJMSTP-00 keyboard and HMAX081-00 matrix.
User action
Joystick for Pan/Tilt/Zoom,[FN] / [FF]
for Focus
[IRIS+] / [IRIS -]
[AUTOIRIS]
[FOCUS AUTO]
[FN] or [FF]
[AUX]
[IRIS -]
[n] [PRESET] or use one of [PRESET
1], [PRESET 2], [PRESET 3],
[PRESET 4]
[1] [AUTOPAN]
hold [PRESET], press [n], release
[PRESET]
[9] [5] [PRESET] or [PRESET 2]
[PRESET 2] within 2 seconds
Joystick for Up/Down/Left/Right.
[PRESET 3] for Set.
* The presets used to access the OSD are programmable via the XTU.
NOTE
RS485 connection; 9600 baud, odd parity, 8 data bits, 1 stop bit.
Camera addressing is 1-254 for cameras 1-254. Also responds to broadcast address 255.
Tested using Videmech Vertex keyboard.
User action
Joystick for Pan/Tilt, [ZI] / [ZO] for
Zoom, [FN] / [FF] for Focus
[IO] / [IC]
[AUX 1] on
[AUX 1] off
[LAMPS] on
[LAMPS] off
[IC]
Notes
When in OSD cursor mode Pan / Tilt operate as cursor right / left /
up / down (but see also Recall Preset 1 below).
Only operates when exposure priority is set to KEYBOARD.
Overridden automatically on a manual iris operation.
Manual control overrides autofocus.
Toggle action. Switches camera between day and night modes
(colour/mono version only). It is not possible to indicate the current
state on the keyboard.
If one-touch white balance is enabled in OSD and exposure priority
is not set to KEYBOARD.
Range 1-99.Preset 95* or Preset 2* twice within 2 seconds functions
as the OSD Mode 'MENU' command. When in OSD mode Preset 1
switches the joystick between cursor and camera control. When in
OSD cursor mode Preset 3 operates as SET.
Starts Tour 1.
Range 1-99.
Recall Preset 95* or Recall Preset 2* twice within 2 seconds
functions as the OSD Mode 'MENU' command.
When in OSD mode Recall Preset 1 switches the joystick between
cursor and camera control. When in OSD cursor mode Recall
Preset 3 operates as SET.
Notes
When in OSD cursor mode Pan / Tilt operate as cursor right / left /
up / down (but see also Recall Preset 1 below).
Only operates when exposure priority is set to KEYBOARD.
Lamps on switches camera to night mode (colour/mono version
only).
Lamps off switches camera to day mode (colour/mono version only).
If one-touch white balance is enabled in OSD and exposure priority
is not set to KEYBOARD.
65
08.2006