Pacific energy PACIFIC FP30 Installation And Operating Instructions Manual
Zero clearance wood fireplace
Hide thumbs
Also See for PACIFIC FP30:
- Installation and operating instructions manual (32 pages) ,
- Installation and operating instructions manual (48 pages) ,
- Installation and operating instructions manual (28 pages)
Table of Contents
Advertisement
Quick Links
IMPORTANT:
THESE INSTRUCTIONS ARE TO
REMAIN WITH THE HOMEOWNER.
PLEASE SAVE THESE INSTRUCTIONS.
SAFETY NOTICE
If this stove is not properly installed, a
house fi re may result. For your safety,
follow the installation instructions. Contact
local building or fire officials about
restrictions and installation inspection
requirements in your area.
TESTED and LISTED to CAN/ULC
S610-M87 AND UL 127
Meets the Environmental Protection
Agency's July 1990 Particulate Emission
Standards
190913-28
INSTALLATION
AND OPERATING
INSTRUCTIONS
MODEL: PACIFIC FP30
ZERO CLEARANCE WOOD
FIREPLACE
PACIFIC FP30
SERIAL #
5055.5152
Advertisement
Table of Contents
Related Manuals for Pacific energy PACIFIC FP30
Summary of Contents for Pacific energy PACIFIC FP30
-
Page 1: Safety Notice
TESTED and LISTED to CAN/ULC S610-M87 AND UL 127 Meets the Environmental Protection Agency's July 1990 Particulate Emission Standards MODEL: PACIFIC FP30 ZERO CLEARANCE WOOD FIREPLACE 190913-28 PACIFIC FP30 5055.5152... -
Page 2: Table Of Contents
Appendix A ................. 24 may result in property damage, bodily Troubleshooting ................... 24 injury, or even death. Understanding & Operating Your Pacifi c Energy Stove ......25 Replacement Parts ................26 Label Location ..................27 Label ....................27 PACIFIC FP30 190913-28... -
Page 3: Safety And Maintenance
(see Floor Protector section on page 18 for Floor Protec- Periodically inspect seals and replace if necessary. tion dimensions) 7. DOOR GLASS - Replacement glass can be obtained from your dealer. Use 11 3/8" x 21 5/8" x 5 mm ceramic glass only. PACIFIC FP30 190913-28... -
Page 4: Maintenance Checks
- Replace if the baffle has permanent warping greater than this or has cracking or breakage. - Please contact your Dealer if you experience any of the damage listed above. Continuing to operate your stove with broken parts may accelerate damage to other parts and may void your warranty PACIFIC FP30 190913-28... -
Page 5: Creosote
In the event of a Chimney Fire 1. Prepare to evacuate to ensure everyone's safety. Have a well understood plan of action for evacuation. Have a place outside where everyone is to meet. 2. Close air inlet on stove. PACIFIC FP30 190913-28... -
Page 6: Operation
3. Use wood of different shape, diameter and length (up to Your PACIFIC ENERGY heater is designed for maximum 20"). Load your wood endwise and try to place the logs overall efficiency at a moderate fi ring rate. Over fi ring is so that the air can fl ow between them. -
Page 7: Over Firing
It is also recommended that the blower be wired to a wall switch or dimmer switch for manual control. If the blower should ever need to be replaced, power to the blower can be shut off at the switch during replacement. PACIFIC FP30 190913-28... -
Page 8: Blower Replacement
8. Reverse the process to re-install blower. FIG. #1 FIG. #4 BOLTS WINGNUTS FIG. #5 Electrical Rating : 115 V, 60 Hz, 1.1A NUTS Thermo Blower Switch TERMINAL BLOCK MALE/FEMALE 110VAC SWITCHED CONNECTION 110VAC COMMON GROUND USE ONLY COPPER CONDUCTORS 120412 5050.7434 PACIFIC FP30 190913-28... -
Page 9: Firebrick Installation
(230 mm x 115 mm x 32 mm) 5096.99 9” X 3 1/2” X 1 1/4” (102 mm x 115 mm x 32 mm) 3245.501 7 1/4” X 4 1/2” X 1 1/4” (184 mm x 115 mm x 32 mm) 245.001 PACIFIC FP30 190913-28... -
Page 10: Fireplace Installation
Penetrate the highest part of the roof. • Be installed as far as possible from roof offsets, trees or any other obstructions that may cause wind turbulence or back drafts in the chimney. • The least amount of offsets (elbows) possible. PACIFIC FP30 190913-28... -
Page 11: Clearances
45 degree cut facing to wards the rear of the unit as shown in Fig. #6 Dimensions 29 1/2" FIG. #7 FP30 25" 30 3/4" 45" 28 1/8" 21 7/8" 11 1/4" 44" PACIFIC FP30 190913-28... -
Page 12: Minimum Framing Dimensions
Minimum Framing Dimensions FIG. #8 NOTE: THE FRAMING DIMENSIONS AROUND THE FIREPLACE INCLUDE THE INNER DRYWALL BOARD. " " " 6 3/8" " " " " " " PACIFIC FP30 190913-28... -
Page 13: Framing Kit Assembly
Using the screws provided (1), attach the framing kit legs(4) to the bottom stud (2). • Next, attach each center support(3) to the bottom stud(2) and then attach the top stud(2) to the center supports(3). FIG. #9 PACIFIC FP30 190913-28... -
Page 14: Minimum Clearances To Combustibles
Minimum Clearances to Combustibles FIG. #10 PACIFIC FP30 190913-28... - Page 15 Non-combustible fl oor protector * 4" diameter combustion outside air inlet. One on either side of unit. The combustion air inlets can be rotated to draw air from the rear of the unit if desired. PACIFIC FP30 190913-28...
-
Page 16: Listed Chimney And Chimney Connector
Cover the insulation with drywall panels need to install an Anchor Plate spacer. Part #FP30.7757) around the fi replace. It is not required to install a chase outlet but doing so can provide extra heat into the room. PACIFIC FP30 190913-28... -
Page 17: Offsets
Maximum chimney height supported by fireplace. 25’ (7.62m) Minimum depth of non-combustible hearth extension: from the front of the 18” (457mm) fireplace. Minimum width of floor protection from side of door opening(in U.S.A.) and from side of unit(in Canada). PACIFIC FP30 190913-28... -
Page 18: Combustion Air
If blockage occurs, fl ue gases may enter living space. A typical outside air connection is shown in Fig. #14. PACIFIC FP30 190913-28... -
Page 19: Floor Protector
Electrical Rating : 115 V, 60 Hz, 1.1A Minimum Overall Depth - 19 1/8" Thermo Blower Switch TERMINAL BLOCK MALE/FEMALE 110VAC SWITCHED CONNECTION 110VAC COMMON GROUND 19 1/8" 8" [203mm] 8" [203mm] [486mm] 120412 5050.7434 18" [457mm] Non-combustible fl oor protector 38 1/2" [978mm] PACIFIC FP30 190913-28... -
Page 20: Remote Heat Duct Installation
1. Using a pair of tin snips, cut away the square section block- ing the heat duct openings and cut out insulation(Fig.#19). 2. Attach the heat duct adapter/s with the screws provided in the FP30.GVKIT (Fig. #19). PACIFIC FP30 190913-28... - Page 21 3/4” thick(Max. 4"), connect additional room air to the 6" Gravity Vent air inlet on the left side of the fi replace casing using the adapter provided(Fig. #22). FLOOR FIG. #22 FIG. #20 WALL OUTLET 11 1/4” 9 3/4” PACIFIC FP30 190913-28...
-
Page 22: Facing And Air Inlet
Tape and mud the joints as per the board manufacturers recommendations. FIG. #24 NON-COMBUSTIBLE CEMENT BOARD 29” REQUIRED DECORATIVE NON-COMBUSTIBLE FACING MAXIMUM 4” THICK 30in2 (194cm2) CHASE AIR INLET 1 1/2” 60.00 ALTERNATE LOCATION FOR CHASE AIR INLET PACIFIC FP30 190913-28... -
Page 23: Mantel Clearances
THIS POINT ELECTRICAL WIRING OR GAS PLUMBING IN THIS AREA. MANTEL CLEARANCE CHART MANTEL CLEARANCE A-CANADA 42”(NO GRAVITY VENT) NON-COMBUSTIBLE 16 1/2” CEMENT BOARD A-CANADA 34"(GRAVITY VENT) -NON-COMBUSTIBLE DECORATIVE FACING A-U.S.A. 34" MANTEL DEPTH 2" TO 12" PACIFIC FP30 190913-28... -
Page 24: Troubleshooting
1. Combustion air supply blocked - Check outside air supply for obstruction - Check that room air cover is removed 2. Draft too low - Chimney plugged or restricted, inspect and clean - Chimney oversized or otherwise unsuitable, consult Dealer PACIFIC FP30 190913-28... -
Page 25: Understanding & Operating Your Pacifi C Energy Stove
1 -Boost Air 4 -Secondary Combustion Zone 2 -Main Combustion Air 5 -Radiant Heat 3 -Air Wash System 6 -Convected Heat PACIFIC FP30 190913-28... -
Page 26: Replacement Parts
*19 ..Gravity Vent Adapter ....... FP30.9128 *20 ..Anchor plate spacer ....... FP30.7757 All parts may be ordered from your nearest Pacifi c Energy NOT SHOWN dealer. Contact Pacifi c Energy for the location of the dealer nearest you. PACIFIC FP30 190913-28... -
Page 27: Label Location
• BLOWER ELECTRICAL RATING 115V, 60HZ, 1.0AMP • REPLACE GLASS ONLY WITH 5mm CERAMIC GLASS. • DO NOT USE OR INSTALL COMPONENTS OR PRODUCTS NOT SPECIFIED IN PACIFIC ENERGY INSTALLATION INSTRUCTIONS. DO NOT USE A FIREPLACE INSERT OR OTHER PRODUCTS NOT SPECIFIED FOR USE WITH THIS PRODUCT. - Page 28 PACIFIC ENERGY FIREPLACE PRODUCTS LTD. 2975 Allenby Rd., Duncan, B.C. V9L 6V8 Phone: 250-748-1184 Web site: http://www.pacifi cenergy.net Printed in Canada...