Pacific energy FP16 Installation And Operating Instructions Manual
  1. Manuals
  2. Brands
  3. Pacific energy Manuals
  4. Indoor Fireplace
  5. FP16
  6. Installation and operating instructions manual

Pacific energy FP16 Installation And Operating Instructions Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

IMPORTANT:
THESE INSTRUCTIONS ARE TO
REMAIN WITH THE HOMEOWNER.
PLEASE SAVE THESE INSTRUCTIONS.

SAFETY NOTICE

If this fi replace is not properly installed, a
house fi re may result. For your safety, follow
the installation instructions. Contact local
building or fi re officials about restrictions
and installation inspection requirements in
your area.
TESTED and LISTED to CAN/ULC
S610-M87 AND UL 127
Meets the Environmental Protection
Agency's May 2015 Particulate Emission
Standards
©PACIFIC ENERGY FIREPLACE
040515-28
PRODUCTS LTD. - 2014
INSTALLATION
AND OPERATING
INSTRUCTIONS
MODEL: FP16 & FP16AR
ZERO CLEARANCE WOOD
FIREPLACE
FP16
SERIAL #
5055.5155

Advertisement

Table of Contents
loading

Related Manuals for Pacific energy FP16

Summary of Contents for Pacific energy FP16

  • Page 1: Safety Notice

    AND OPERATING INSTRUCTIONS TESTED and LISTED to CAN/ULC S610-M87 AND UL 127 Meets the Environmental Protection Agency's May 2015 Particulate Emission Standards MODEL: FP16 & FP16AR ZERO CLEARANCE WOOD FIREPLACE ©PACIFIC ENERGY FIREPLACE 040515-28 FP16 5055.5155 PRODUCTS LTD. - 2014...

  • Page 2: Table Of Contents

    PLEASE SAVE THESE INSTRUCTIONS This manual describes the installation and operation of the Pacifi c Energy, FP16 wood heater. This heater meets the 2015 U.S. Environmental Protection Agency's crib wood emission limits for wood heaters sold after May 15, 2015. Un- der specifi c test conditions this heater has been shown to deliver heat at rates ranging from 10,800 to 24,600 Btu/hr.

  • Page 3: Safety And Maintenance

    (see Floor Protector section on page 19 for Floor Protection 6. DOOR GLASS - Replacement glass can be obtained from dimensions) your dealer. Use 16-1/2”(419mm) x 10-1/2”(267mm) x 5 mm ceramic glass only. FP16 040515-28 ©PACIFIC ENERGY FIREPLACE PRODUCTS LTD.

  • Page 4: Maintenance Checks

    - Please contact your Dealer if you experience any of the damage listed above. Continuing to operate your fi replace with broken parts may accelerate damage to other parts and may void your warranty ©PACIFIC ENERGY FIREPLACE FP16 040515-28 PRODUCTS LTD.

  • Page 5: Chimney Smoke And Creosote Formation

    It is damp if it turns black and lights within three minutes. If it sizzles, hisses and blackens without igniting in fi ve minutes it is soaked and should not be burnt. FP16 040515-28 ©PACIFIC ENERGY FIREPLACE PRODUCTS LTD.

  • Page 6: Operation

    This heater is not designed for open door burning. Your PACIFIC ENERGY heater is designed for maximum If unit is operated with the door open, gases and fl ame overall efficiency at a moderate fi ring rate. Over fi ring is may be drawn out of the fi replace opening creating risks hazardous and a waste of fuel.

  • Page 7: Restarting After Extended Or Overnight Burns

    Whenever ashes get 3(76mm) to 4(102mm) inches deep in your fi rebox, remove excess ashes. Leave an ash bed approximately 1" (25 mm) deep on the fi rebox bottom to help maintain a hot charcoal bed. FP16 040515-28 ©PACIFIC ENERGY FIREPLACE PRODUCTS LTD.

  • Page 8: Baffle Removal

    Inspect airbox for debris. If debris is present, carefully use a vacum to suck debris through the hole in the fi rebox bottom. 3. Replace the cover plate and the bricks. ©PACIFIC ENERGY FIREPLACE FP16 040515-28 PRODUCTS LTD.

  • Page 9: Glass Cleaning

    5. Remove the three screws securing the blower to the To wall mounting bracket and replace the blower. Fig. #3 switch/control 6. Reverse all previous steps to reinstall the new blower. G (ground) L1 (hot) L2 (neutral) Junction FP16 040515-28 ©PACIFIC ENERGY FIREPLACE PRODUCTS LTD.

  • Page 10: Firebrick Installation Instructions

    - Next, install the side fi rebricks, 3 each side. - Lastly, place 4 fi rebricks on the bottom of the heater. ITEM SIZE PART NUMBER 9” X 4 1/2” X 1 1/4” (230 mm x 115 mm x 32 mm) 5096.99 ©PACIFIC ENERGY FIREPLACE FP16 040515-28 PRODUCTS LTD.

  • Page 11: Crate Removal

    72"(1.83m) measured from the base of the appliance to the ceiling is required. The FP16 fi replace may not be installed in a factory built fi replace unless tested with the fi replace. Wind direction and magnitude can play a factor in the chimney performance.

  • Page 12: Dimensions

    18 5/8" 39" [991mm] 28 1/2" 4 1/2" 38" Minimum Clearances to Combustibles FIG. #6 " 21" 133mm 533mm 2" ” 14" 51mm 543mm 356mm " 765mm 2" 51mm STANDOFFS NOT SHOWN 2" 51mm ©PACIFIC ENERGY FIREPLACE FP16 040515-28 PRODUCTS LTD.

  • Page 13: Minimum Framing Dimensions

    DIMENSIONS WILL NEED TO BE ADJUSTED ACCORDINGLY 42" TO ACCEPT DRYWALL IF 1.07m USED INSIDE ENCLOSURE. " 1.45m " 546mm 2" 51mm " " 1.45m 42" 772mm 1.07m 81" 2.06m " 1.41m 42" 1.07m FP16 040515-28 ©PACIFIC ENERGY FIREPLACE PRODUCTS LTD.

  • Page 14: Framing Kit Assembly

    Using the screws provided (1), attach the framing kit legs(4) to the bottom stud (2). • Next, attach each center support(3) to the bottom stud(2) and then attach the top stud(2) to the center supports(3). FIG. #9 ©PACIFIC ENERGY FIREPLACE FP16 040515-28 PRODUCTS LTD.
  • Page 15 Non-combustible fl oor protector * 4"(102mm) diameter combustion outside air inlet. One on either side of unit. Also one in rear and on bottom of base plate if desired. FP16 040515-28 ©PACIFIC ENERGY FIREPLACE PRODUCTS LTD.

  • Page 16: Chase/Enclosure

    MANUFACTURER'S FIREPLACE ANCHOR PLATE. NOTE: Check local codes concerning installation requirements and restrictions in your area. NOTE: The FP16 must be installed so the outlet of the chimney system is a minimum 15ft(4.6m) in height as measured from the base of the unit.

  • Page 17: Offsets

    NOTE: IT IS REQUIRED THAT ALL CHIMNEY SYSTEM CONNECTIONS BE SECURED WITH (3)-#8 X ½"(12 MM) The chimney for the FP16 can be installed with a maximum METAL SCREWS. of four 45° elbows(in Canada) and four 30° elbows(in FIG. #10 U.S.A.) as shown in Fig.

  • Page 18: Combustion Air

    If blockage occurs, WARNING: THE COMBUSTION AIR INLET fl ue gases may enter living space. MUST BE AT LEAST 5ft(1.5m) BELOW CHIM- NEY FLUE AND MUST NEVER TERMINATE IN ATTIC SPACES. ©PACIFIC ENERGY FIREPLACE FP16 040515-28 PRODUCTS LTD.

  • Page 19: Framing

    The wood framing must be installed as shown below with no wood framing directly in front of the chimney. The front facing area of the FP16 must be covered with The cement board must cover from the fl oor to the ceiling non-combustible cement board prior to applying any non- and the full width of the unit(42"(1.07m)).

  • Page 20: Ember Protection

    Floor Blower Wiring 18" [457mm] 8" [203mm] 8" [203mm] The FP16 blowers must be connected to 120 VAC house hold electrical system. Non-combustible fl oor protector It is recommended to also connect the circuit to a wall switch or fan speed controller.(not supplied) 49 1/2"...

  • Page 21: Mantel Clearances

    7"(178mm) 48"(1.22m) 8"(203mm) 48 1/2"(1.23m) 9"(229mm) 49"(1.25m) 10"(254mm) 49 1/2"(1.26m) 11"(279mm) 50"(1.27m) 12"(305mm) 50 1/2"(1.28m) Combustible Mantle (A) 12"(305mm) (A)4"(102mm) 6'(1.83m) Floor to ceiling Minimum (B) 50 1/2" 1.28m (B) 46 1/2" 1.18m FP16 040515-28 ©PACIFIC ENERGY FIREPLACE PRODUCTS LTD.

  • Page 22: Troubleshooting

    - Chimney plugged or restricted, inspect and clean - Chimney oversized or otherwise unsuitable, consult Dealer 3. Baffle not installed correctly - check to see that the baffle is properly installed over the air tube and locking pin is installed ©PACIFIC ENERGY FIREPLACE FP16 040515-28 PRODUCTS LTD.

  • Page 23: Understanding & Operating Your Pacifi C Energy Fireplace

    1 -Boost Air 4 -Secondary Combustion Zone 2 -Main Combustion Air 5 -Radiant Heat 3 -Air Wash System 6 -Convected Heat FP16 040515-28 ©PACIFIC ENERGY FIREPLACE PRODUCTS LTD.

  • Page 24: Replacement Parts

    ITEM DESCRIPTION PART NO. 1.... Quadrant ............7953 13 ..Front Trim Plate, Black ......FP16 .F T M B K A 2.... Blower Assembly, LHS ......NE16.7844 Front Trim Plate, Stainless Steel ......FP16.FTSSA ....Blower only, LHS ........5024.701 14 ..Firebrick Set ........NE16.INSBRIC 3....

  • Page 25: Warranty Information

    Pacifi c Energy is not responsible for installation, operational or environmental conditions beyond our control. (The company may, at its discretion, discharge all obligations by refunding the wholesale price of the defective part.) For Warranty claims, please contact your nearest Pacifi c Energy dealer. FP16 040515-28 ©PACIFIC ENERGY FIREPLACE PRODUCTS LTD.
  • Page 26 ©PACIFIC ENERGY FIREPLACE FP16 040515-28 PRODUCTS LTD.

  • Page 27: Label Location

    • BLOWER ELECTRICAL RATING 115V, 60HZ, 1.1AMP • REPLACE GLASS ONLY WITH 5mm CERAMIC GLASS. • DO NOT USE OR INSTALL COMPONENTS OR PRODUCTS NOT SPECIFIED IN PACIFIC ENERGY INSTALLATION INSTRUCTIONS. DO NOT USE A FIREPLACE INSERT OR OTHER PRODUCTS NOT SPECIFIED FOR USE WITH THIS PRODUCT. • THIS FIREPLACE HAS NOT BEEN TESTED WITH AN UNVENTED GAS LOG SET.
  • Page 28 PACIFIC ENERGY FIREPLACE PRODUCTS LTD. 2975 Allenby Rd., Duncan, B.C. V9L 6V8 For technical support, please contact your retailer. Web site: http://www.pacifi cenergy.net Printed in Canada...

This manual is also suitable for:

Fp16ar

Table of Contents